Question about 2001 Mitsubishi Diamante

1 Answer

2001 diamante abs light on

Hello I've reading different stories about the abs systems of different cars but can't seem to find anything regarding my car...does any one know if the sensor is magnetic? and if so and clean could that fix the problem..also if the wheel that the sensor get's the signal from if it is dirty could that cause the problem? also it seems that the connection to disconnect and check the ohms is really difficult to get to...any help will be greatly appreciated..thanks

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Genius:

    An expert who has answered 1,000 questions.

  • Mitsubishi Master
  • 1,207 Answers

Do you take a car obd2 code scanner to have a check? you can know the real problem form it.

Posted on Jan 17, 2013

Ad

3 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad
  • 1026 Answers

SOURCE: 2001 Mitsubishi Diamante

ya need keys get from radio shack r mitisbishi
they insert in to slots or holes on radio to remove

Posted on Apr 05, 2010

  • 10 Answers

SOURCE: Mighty Max Brake Lights, Stereo & Clock all stopped working at the same time. Any suggestions?

you may have a bad ground, or a short in one of the wires. pull out the stereo.

Posted on Aug 19, 2012

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Is it possiable for abs senser to shut down transmission on 1997mustang?


ABS is a different systems & module, than the transmission
controls

So not really-- but you may have an issue with the abs, if you
have fault codes in the system & some driveability sympthoms
that seem like there is a trans & other problems

Nov 05, 2014 | 1997 Ford Mustang Cobra

2 Answers

ABS, TracOff, and Service Vehicle lights stay on after starting


Its possible you damaged one of the wheel sensors or the wiring when you were working on the starter. Or not.
The ABS and traction control uses components from both systems, so if one system fails both are disabled.
I would check that wheel sensor and see if it is working. You may need a professional scanner to check it out, and to erase the codes once the problem is fixed.

Jul 05, 2013 | 2001 Pontiac Grand Am SE

1 Answer

Stabilitrak and ABS lights come on but car is running fine


Nope, but take it in. Brake problems are nothing to fool with They'll probabl tell you it's the ABS ECU. Not a cheap item.. However, it only affects the ABS system, not the brakes itself.

Jan 16, 2013 | 2008 Pontiac Torrent

1 Answer

Lexus es300 acceleration problem, dangerous speeds


Sorry Danielle but your vehicle does not have electronic throttle control . Your best bet take it to a qualified repair shop that knows your vehicle better then you .

May 13, 2017 | Lexus ES 300 Cars & Trucks

1 Answer

Mazda Tribute v6 2002 5-8 seconds to start


sounds like a problem with the ignitionkey comuting with body control module verifying that it is the right key for the car. if you have another key and see if it does the same. reprogramming of keys may help. Prados have been known to have a similar prob.

Nov 17, 2012 | 2002 Mazda Tribute

1 Answer

My abs light and the skid light is staying on


Hi K, Seems the wheel speed sensors are dirty or damaged due to where you've been driving. The remedy is to have diagnostic scan carried out, from which the defective unit or units will be identified and the appropriate action recommended. Regards John

Aug 30, 2012 | 2007 Lincoln MKX

1 Answer

I've changed all my brake parts awhile back but now I'm getting a warning lights for my ABS system on my 2005 X3. Not clear why the light is on, and the dealer is no help.


  • ABS is Antilock Braking System. Basically it prevents your wheels from locking up and skidding out of control when you stomp on the brakes. On older vehicles you would pump the brakes with your feet manually but with ABS this happens automatically.


  • ABS while part of the braking system is not something that would be addressed during a brake job. The ABS sensor are inside the hub. You would need to remove the wheel to access this.


  • If your ABS light is going on then you either have a failure in the power feed to your ABS sensor or the ABS an sensor is failing. Your BMW should have an ABS sensor on every hub. On occasion a brake light being out can cause an ABS light to come on the dash but this is a rare occasion.


  • To test your ABS sensor you remover the wheel and in the top of the HUB (bearings) you will see the sensor and connector. Remove the connector and check for resistance with a multi meter.


  • I'm concerned the dealership could not help. With that light on the should be able to hook a scanner up the the vehicle and see what exactly is wrong and where. You may want to consult a different dealership. You can test things just as easily.


  • Hope this helps and thank you for using FixYa.


Regards, Tony

Jun 22, 2011 | BMW X3 Series Cars & Trucks

1 Answer

My Lincoln Navigator has been to 4 diff shops, please help


to me this sounds more like a wheel speed sensor than anything to do with the actual brakes itself, my brother had a similar problem with his 03 F150. i replaced the wheel speed sensors and the problem seemed to disapate.

Jul 13, 2009 | 1998 Lincoln Navigator

1 Answer

ABS Brakes come on when stopping all the time. Is there a sensor?


The ABS system always is engaged when the brakes are applied. If you are talking about the ABS light coming on then it is a little bit of a different story. If the light has come on at all there will always be a code stored. I would take it to a shop that has a scan tool to read ABS lights and ask them what the computer is saying. This is the only true way to get this problem fixed.

Jun 10, 2009 | 2002 GMC Yukon XL

Not finding what you are looking for?
2001 Mitsubishi Diamante Logo

87 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mitsubishi Experts

yadayada
yadayada

Level 3 Expert

80339 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8841 Answers

Are you a Mitsubishi Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...