Question about 2000 Buick Park Avenue

1 Answer

How do I replace a thermostat in a 2000 buick park ave

Replace thermostat

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Greenhorn:

    A rookie expert who has answered 20 questions on their first day.

    Cheetah:

    An expert who has answered 20 or more questions within one hour.

  • Expert
  • 81 Answers

Drain radiator remove hose remove two bolt on thermostat houseing clean place new thermostat in copper side with spring down in hole revers steps

Posted on Jan 21, 2013

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 1596 Answers

SOURCE: power door lock switch replacement




Remove or Disconnect

Door handle trim plate.

  1. .Install or Connect

  2. Electrical connector and door lock cable.
  3. Trim panel by engaging hooks on backside of panel.
  4. Push pin fastener in defroster duct.
  5. Screw from behind lamp assembly.
  6. Courtesy lamp assembly.
  7. Two screws in arm rest.
  8. Arm rest cover plate.
  9. Door handle trim plate.
There May Be A Need to Drill Out RIVETS that Hold Motor in place,. Just Replace with>>MACHINED SCREWS & BOLT'S




Remove or Disconnect

  1. Trim panel. See: Doors, Hood and Trunk\Doors
  2. Four tabs retaining switch.
  3. Electrical connector.
Install or Connect

  1. Electrical connector.
  2. Snap switch into trim panel.
  3. Trim panel.

Posted on Mar 14, 2009

c17hydro
  • 2984 Answers

SOURCE: try to locate body control module on a 94 buick park ave

BCM --The Body Control Module is located on the right side of the vehicle and positioned under the instrument panel. In order to gain access to the module, it will be necessary to first remove the trim panel.

Posted on Jun 23, 2009

sawdust46694
  • 398 Answers

SOURCE: How do you replace the serpentine belt on a 2000

there is a pic under the hood that showes the corect way to run the belt. over and under diferant pulleys. figure out the corect way it goes and use a breaker bar to pull the tenchenor so you can slide the belt on, then let go slow and your done. the soring holds the pulley at the exact right tension. you can do this it's not that hard... good luck
saw

Posted on Jul 09, 2009

carlsbiz
  • 1124 Answers

SOURCE: replace 2000 buick park ave serpentine belt

Firt - study & write down (draw) the belt path,,
and be sure about it..

Then - put a wrench on the nut in the center of the tension pully.. Move the tension pully to loosen the belt.. Pull belt off..

Repeat to put new one on..

Should be pretty easy..

Posted on Jul 09, 2009

Mustgo
  • 2359 Answers

SOURCE: how do I replace cv boot on a buick park ave

The boot you need to replace is call OUTER CV BOOT.

The quickest way to inspect is to drive it in low speed (UNDER 10 mph) tight left and right turns.

If you hear clicking sound then the CV shaft is bad.

It's also depending on how long the CV boot been crack.

===
If you decide to go ahead on the job then please observe safety and use jack stands to fully support the front end.

Remove wheel,cotter pin,retainer cap and larger axle nut.

Make alignments markings on the strut tower and steering mount so your front end will able to put back to alignment.

You will need an able body to do the following.

Remove the large lower strut bolts and swing the strut off the CV.

DO NOT ROCK THE CAR!!!

Clean off the outer CV.

Install boot,grease and the two bands.

Line up the strut and steering yoke marks

repack bearings,lock nut,cap,cotter pin,wheel.


Drive the car in low speed for 1 miles with tight turns.

Do a quick inspection to make sure the CV boot is sitting perfectly on the CV.

















Posted on Nov 16, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Bought 2000 buick park ave. ultra & do not know how to adj drivers seat up or down.


should have buttons on your armrest or down on the side of the seat by the drivers door if not check in front of the seat

Nov 24, 2013 | 1993 Buick Park Avenue

1 Answer

Tcc solenoid replacement 2000 buick park ave.


Not easily at all
Have to drop one side of sub frame to remove
trans side cover I believe

Jul 28, 2013 | Cars & Trucks

1 Answer

Thermostat for park ave


Click here to see,this is the same 3.8 engine as yours,just not listed under Buick.

Jan 17, 2013 | 2000 Buick Park Avenue

1 Answer

How to change the thermostat on 2000 buick park ave ultra


The thermostat is located under the cover that the upper radiator hose connects to on the engine, let engine cool and remove plastic cover over engine and then remove the 2 bolts that hold the thermostat cover down, replace the thermostat exactly as the old one came out, refill the system with the bleeder valve open on the top of the cover over the thermostat until coolant comes out as you fill, this bleeds our out.

Nov 05, 2012 | 2000 Buick Park Avenue

1 Answer

How to replace a fuel pump on a 2000 buick park ave


It's not easy but heres a guide Hope it can help you.


http://autorepair.about.com/od/fixityourself/ss/fuel_pump_repl.htm

Jun 30, 2010 | 2000 Buick Park Avenue

2 Answers

Replace 2000 buick park ave serpentine belt


Firt - study & write down (draw) the belt path,,
and be sure about it..

Then - put a wrench on the nut in the center of the tension pully.. Move the tension pully to loosen the belt.. Pull belt off..

Repeat to put new one on..

Should be pretty easy..

Jul 09, 2009 | 2000 Buick Park Avenue

1 Answer

No heat or temp gauge read out


Follow top radiator hose back to engine were hose clamps on is called goose neck under that is were thermostat is.

Mar 13, 2009 | 1993 Buick Park Avenue

Not finding what you are looking for?
2000 Buick Park Avenue Logo

181 people viewed this question

Ask a Question

Usually answered in minutes!

Top Buick Experts

yadayada
yadayada

Level 3 Expert

75822 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8202 Answers

Are you a Buick Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...