Question about Toyota Yaris

Open Question

Toyota Yaris 1999 Replacement Headlight/headlamp Japanese or French? Electrical Connecter

Hey, I need to replace the headlights for my Toyota Yaris 1999, but have found that the car was either produced in Japan or French, and each have different electrical connectors within the headlights, I have found replacement headlights with triangle connectors, but no way of knowing what connector was used with which build. i.e. did japan or france use triangle electrical connectors and what did the other use?

Posted by on

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

No low beam head lights on 1999buick regal


Do you know how to do basic automotive electrical testing ?

Headlamps Inoperative - Low Beams

Disconnect the headlamp switch.
Turn the headlamp dimmer switch to the LOW position.
Using a test light, frontprobe between the headlamp switch harness connector terminal D to ground.
Does the test light illuminate? YES - NO ?

2
Using a test light, probe between the headlamp switch harness connector terminal D to ground.
Does the test light illuminate?
--
YES - Go to Step 3
NO - Go to Step 4
3
Replace the headlamp switch. Refer to Headlamp Switch Replacement .
Has the repair been made?
--
Go to Headlight System Check
--
4
Repair a poor connection or an open in circuit 1750 between the headlamp switch and the harness connector terminal A and G201.
Has the repair been made?
--
Go to Headlight System Check
--
5
Reconnect the headlamp switch.
Using a test light, backprobe between connector C201 terminal A3 and ground.
Does the test light illuminate?
--
Go to Step 6
Go to Step 7
6
Repair a poor connection or an open in circuit 10 between the harness connector C201 terminal A3 and S221.
Has the repair been made?
--
Go to Headlight System Check
--
7
Using a test light, backprobe between connector C201 terminal A2 and ground.
Does the test light illuminate?
--
Go to Step 8
Go to Step 9
8
Replace the headlamp dimmer switch. Refer to Multifunction Turn Signal Lever Replacement - On Vehicle .
Has the repair been made?
--
Go to Headlight System Check
--
9
Using a test light, backprobe between the underhood accessory wiring junction block harness connector C2 terminal F10 to ground.
Does the test light illuminate?
--
Go to Step 11
Go to Step 10
10
Replace the underhood accessory wiring junction block. Refer to Accessory Wiring Junction Block Replacement .
Has the repair been made?
--
Go to Headlight System Check
--
11
Repair a poor connection or an open in circuit 1201 between the underhood accessory wiring junction block harness connector C2 terminal F10 and connector C201 terminal A2.
Has the repair been made?
--
Go to Headlight

Feb 18, 2017 | 1999 Buick Regal

1 Answer

How to replace headlights on 1989 toyota camry


1989 Toyota Camry

A little personal tip - if you get fingermarks on a halogen headlamp, you can wipe them off with rubbing alcohol (isopropyl alcohol) or, if you want to do what mechanics do, keep a number of 2X2 alcohol wipes in your automotive toolbox just to wipe off halogen headlight bulbs.

HEADLAMP REMOVAL & INSTALLATION

Sealed Beam Headlamps

See Figures 2 and 3

Before making a headlight replacement, make sure that the headlight switch is in the off position.

1. Loosen the screws, release the clips and remove the headlight door. To release the clips, insert a flat blade screwdriver into the jaws of the clip and pry on the jaws.

2. Remove the beam unit retaining ring screws and remove the beam unit.

Fig. 2: Headlamp door clip removal

3. Compress the lock releases and disconnect the wire connector from the headlight. If the connector is tight, wiggle it while holding in the lock releases and pulling out.

Fig. 3: Do not remove the adjusting screws when removing the head lamp sealed bulb

Never try to loosen the aim adjusting screws. If the screws are loosened, the headlights will have to be re-aimed by a qualified technician.

4. When installing, use only a sealed beam unit with the same part number and wattage.

Composite Headlamps

See Figures 4, 5 and 6

Fig. 4: Headlight bulbs are inside the sockets located in the engine compartment

Fig. 5: Detach the wiring from the back of the headlamp bulb

This procedure only applies to replaceable halogen headlight bulbs (such as Nos. 9004 and 9005); it does not pertain to sealed beam units.

1. Open the vehicle's hood and secure it in an upright position.

Fig. 6: Twist and pull the bulb out, but do not touch the bulb if it is still good

2. Unfasten the locking ring which secures the bulb and socket assembly, then withdraw the assembly rearward.

3. If necessary, gently pry the socket's retaining clip over the projection on the bulb (use care not to break the clip.) Pull the bulb from the socket.

To install:

4. Before installing a light bulb into the socket, ensure that all electrical contact surfaces are free of corrosion or dirt.

5. Line up the replacement headlight bulb with the socket. Firmly push the bulb onto the socket until the spring clip latches over the bulb's projection.

WARNING
Do not touch the glass bulb with your fingers. Oil from your fingers can severely shorten the life of the bulb. If necessary, wipe off any dirt or oil from the bulb with rubbing alcohol before completing installation.

6. To ensure that the replacement bulb functions properly, activate the applicable switch to illuminate the bulb which was just replaced. (If this is a combination low and high beam bulb, be sure to check both intensities.) If the replacement light bulb does not illuminate, either it too is faulty or there is a problem in the bulb circuit or switch. Correct if necessary.

7. Position the headlight bulb and secure it with the locking ring.

8. Close the vehicle's hood.

Fig. 1 - various automotive lamps

10_4_2011_8_32_12_pm.jpg

Fig.2 - Headlamp Door Clip Removal

10_4_2011_8_32_40_pm.jpg

Fig. 3: Do not remove the adjusting screws when removing the head lamp sealed bulb


10_4_2011_8_33_24_pm.jpg

Fig. 4: Headlight bulbs are inside the sockets located in the engine compartment


10_4_2011_8_33_51_pm.jpg

Fig. 5: Detach the wiring from the back of the headlamp bulb


10_4_2011_8_34_22_pm.jpg

Fig. 6: Twist and pull the bulb out, but do not touch the bulb if it is still good.

10_4_2011_8_34_49_pm.jpg

Oct 03, 2011 | 1989 Toyota Camry

1 Answer

How to replace toyota matrix front headlight bulb


Hi,

Replacing a headlight on a Toyota Matrix is a simple process that only requires the use of a screwdriver and a replacement bulb. The Matrix uses 9006 bulbs for the low beams and 9005 bulbs for the high beams. Headlight bulbs can be purchased at auto parts stores.
Replacing Low Beam Bulb
  1. Turn off the engine of the Matrix and open the hood
  2. Rotate the bulb base in the headlamp assembly counterclockwise to remove the low beam bulb. Unplug the electrical connector. If the connector is too tight, wiggle it slightly to help remove it.
  3. Install a new bulb into the connector and place it into the assembly. Rotate it clockwise to lock it into place. Close the hood.
Replacing High Beam Bulb
  1. Turn off the engine of the Matrix and open the hood. If replacing the left-hand headlight, remove the air cleaner duct by removing the securing clip with a screwdriver and pulling the duct out of the vehicle.
  2. Turn the bulb base counterclockwise to remove it. Unplug the electrical connector.
  3. Install a new bulb into the connector and place the bulb into the assembly. Rotate it clockwise to lock it into place. Reattach the air cleaner duct if replacing the left-hand headlight. Close the hood
I hope this helps.

Best regards.

Oct 29, 2010 | 2005 Toyota Matrix

1 Answer

How to take off headlight unit off toyta yaris 1.3 5 door hatchback 2001 to replace headlights


good day, heres some steps. open the hood. remove the headlight terminal, take the boot off, there a pin lock u can find remove it then remove the bulb. note: please dont touch the headlight bulf itself, you can try holding on to the metal casing. hope this helps, have a nice day

Feb 08, 2010 | 2007 Toyota Yaris

1 Answer

Headlight replacement on a 1991 pontiac grand am


Sealed Beam Type
  1. Disconnect the negative battery cable.
  2. Unfasten the headlight bezel attaching screws, then remove the bezel.
8ed2813.gif
Remove the headlight bezel

To avoid turning the vertical or horizontal aiming screws, refer to the illustration before removing the headlight retainer.
  1. Unfasten the headlight retainer attaching screws, then remove the retainer.
e11bb51.gif
Remove the headlight trim screws then...

67522f3.gif
... pull the trim off while holding the bulb

4. Pull the headlight out, then carefully detach the electrical connector.

8d80048.gif
Pull the bulb out far enough to disconnect the wiring


To install:
  1. Attach the electrical connector to the new headlamp.
  2. Place the headlamp into the socket.
  3. Install the retainer, then tighten the attaching screws.
  4. Connect the negative battery cable, then turn the headlight switch on, to be sure the headlights are operating.
  5. Install the headlight bezel and secure using the attaching screws.

Jan 18, 2010 | 1991 Pontiac Grand Am

1 Answer

1999 toyota sienna replacement the headlight set


Ask the dealer about the lens. That is where 98% come from

Sep 29, 2009 | 1999 Toyota Sienna

2 Answers

How do i remove headlight assembly on 99 camry?


This video will show you how to remove them on your vehicle.">

Apr 19, 2009 | 1999 Toyota Camry

2 Answers

Headlight bulb replacement 1999 f150 p/u


Is it that complicated? I heard that all you need to do is pull up on some clips and then pull the headlights out.

Jan 29, 2009 | 1999 Ford F150 Regular Cab

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

70 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toyota Experts

yadayada
yadayada

Level 3 Expert

75797 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8140 Answers

Are you a Toyota Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...