Question about Ford E-150

Open Question

Need 1990 e-150 door latch mechanism diagram - E-150 Ford Cars & Trucks

Posted by on

Ad

4 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get to try the service completely Free afterwhich it costs $6 per call and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
ganyapr
  • 33 Answers

SOURCE: I need information on how

Removal

  1. Disconnect battery ground cable (14301).
  1. Remove front door trim panel (23942) and watershield from front door (20124).
  1. Mark the location of the bolt retaining front door glass run front retainer (21572). Remove the bolt.
  1. Check all rod connections against the appropriate illustration. Correct any disconnected or loose connections and check operation before replacing parts.
  1. Remove power door lock actuator (218A42).
  1. Disconnect the rods from the front door latch (21812). The front door latch remote control link (21940) and the latch-to-lock cylinder rod cannot be removed at this time because of the rod's end configuration. Remove wiring from clip on front door latch shield.
  1. Remove front door latch control cylinder rod (22134) from the door lock cylinder (21985).
  1. Remove front door latch remote control and link (21818).
  1. Remove the front door latch retaining screws. Disconnect the door open warning lamp switch (14018) if so equipped. Remove the front door latch from the front door.
  1. NOTE: Do not damage anti-theft shield.
    Remove anti-theft shield from the front door latch.
  1. Remove front door latch remote control link, front door latch control cylinder rods and door open warning lamp switches from front door latch where applicable.
Installation
  1. Follow removal procedure in reverse order.
  1. Tighten front door latch retaining screws 4-8 Nm (36-70 lb-in).


    ganyapr_5.gif


Item Description 1 Front Door Latch Control Cylinder Rod 2 Front Door Latch Remote Control Link 3 Bushing 4 Door Latch Shield 5 Power Door Lock Actuator 6 Front Door Latch Control Cylinder Rod 7 Front Door Latch 8 Latch (1 Req'd) 9 Screws (2 Req'd)

Posted on Feb 13, 2011

Ad
jaysonemanme
  • 500 Answers

SOURCE: Need detailed diagram of 1998 latch mechanism to remove connections from it

there is no diagram... the latch is also a non-servicable latch, so if your problems in the latch- it needs a latch. i would look more closely at the outside door handle itself as i have seen a few of them break on the E series vans.you may be able to get detailed instructions thru autozone.com or @ autozone. hope this helps and good luck

Posted on May 29, 2009

  • 330 Answers

SOURCE: The passenger door latch will

hello there
what model and a year of your Porsche do you have?
proporsche@yahoo.com

proporsche

Posted on May 30, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

My fuel door wont open. is there a bypass switch or something


Is it electric or mechanical?

Some use a cable and latch while others use an electromagnetic mechanism.

If it is electric. It may be easy to find the problem, switch or fuse or at least you could, with a wiring diagram, apply power to the circuit bypassing the switch.

If it is mechanical, the cable may not be getting pulled with the lever and pulling it with a pair of pliars may open it. Be careful not to link the cable when you grip it. If it just needs lubrication at the door or latch, operate the release and have someone pry it open gently when the switch or cable is activated, then lubricate the latch.

Nov 27, 2016 | Cars & Trucks

1 Answer

Need a diagram of a 2000 ford expidtion door


there should only be three rods at door latch one to door handle that has plastic locking clip one the goes from key cylinder to latch under locking clip and if power locks one to power lock actuator.

Aug 16, 2014 | Cars & Trucks

1 Answer

Toyota rav4 back door latch problem


Well, it could be something as simple as the latch mechanism needs to be lubricated. Spray some lub spray, wd 40, etc into the mechanism and work the latch a bit. Maybe that will work. You nver know!

Mar 30, 2014 | 2008 Toyota RAV4

2 Answers

Back hatch wont open jeep cherokee 01


the switch in the back door will get seized with age. When this happens the latch assembly will stay stuck halfway open and closed allowing you to close the door. when the door locks the latch will jam. and now will not be able to open until the latch is freed up and unseized again. you will have to access the latch by going through the inside and popping the panel away from the door. then using a screw driver force the latch to the fully closed position. then unlock door and open. Lubricate the old latch till it moves freely. then it should work properly for you.. good luck

Oct 27, 2011 | 2001 Jeep Cherokee

1 Answer

I need information on how to replace (or service) the door latch mechanism on my merc. I have realigned the door (and realigned the striker rod) and it will still not close. The latching system does not...


Removal
  1. Disconnect battery ground cable (14301).
  1. Remove front door trim panel (23942) and watershield from front door (20124).
  1. Mark the location of the bolt retaining front door glass run front retainer (21572). Remove the bolt.
  1. Check all rod connections against the appropriate illustration. Correct any disconnected or loose connections and check operation before replacing parts.
  1. Remove power door lock actuator (218A42).
  1. Disconnect the rods from the front door latch (21812). The front door latch remote control link (21940) and the latch-to-lock cylinder rod cannot be removed at this time because of the rod's end configuration. Remove wiring from clip on front door latch shield.
  1. Remove front door latch control cylinder rod (22134) from the door lock cylinder (21985).
  1. Remove front door latch remote control and link (21818).
  1. Remove the front door latch retaining screws. Disconnect the door open warning lamp switch (14018) if so equipped. Remove the front door latch from the front door.
  1. NOTE: Do not damage anti-theft shield.
    Remove anti-theft shield from the front door latch.
  1. Remove front door latch remote control link, front door latch control cylinder rods and door open warning lamp switches from front door latch where applicable.
Installation
  1. Follow removal procedure in reverse order.
  1. Tighten front door latch retaining screws 4-8 Nm (36-70 lb-in).


    ganyapr_5.gif


Item Description 1 Front Door Latch Control Cylinder Rod 2 Front Door Latch Remote Control Link 3 Bushing 4 Door Latch Shield 5 Power Door Lock Actuator 6 Front Door Latch Control Cylinder Rod 7 Front Door Latch 8 Latch (1 Req'd) 9 Screws (2 Req'd)

Feb 13, 2011 | 1997 Mercury Cougar XR7

1 Answer

How does the door linkage work i.e a diagram


There are plastic connectors that attach to the rod and attach to the latch. The rod usually hooks into the inside latch, the rod may be held to the door by some clips. Then the rod connects to the latch with a plastic retainer clip.

Mar 13, 2010 | 1993 Honda Civic 4 Door

2 Answers

Electrical issues


Sounds like one of the door switches is broken. On your model, it could be a small plunger by the front of each door jamb, or the latch itself. Check them all for visible damage first, then test each on for function.

Oct 06, 2009 | 2004 Ford Explorer

1 Answer

Need detailed diagram of 1998 latch mechanism to remove connections from it


there is no diagram... the latch is also a non-servicable latch, so if your problems in the latch- it needs a latch. i would look more closely at the outside door handle itself as i have seen a few of them break on the E series vans.you may be able to get detailed instructions thru autozone.com or @ autozone. hope this helps and good luck

May 28, 2009 | 2003 Ford E150

2 Answers

Door Ajar light and dinger, interior lights stay on, looking for a fuse diagram.


It drove me nuts too. Fortunately, the solution is both cheap and simple. There is a latch mechanism in each side of the tailgate which gets all filled with dirt and slime.The latch jaws start to stick and dont move far enough to close the door ajar switch inside the tailgate Spray each latch generously with WD40, wipe the mechanisms off with a rag, close the tailgate, open the tailgate and repeat the cleaning several times. As soon as you get everything freed up, the switch will be able to report that the tailgate is closed and the problems will be gone. If you want, afterwards you can spray a little lithium grease on the latches to keep things running smooth. You may need to use a screwdriver to completely pry open the jaws in conjunction with opening the tailgate handle to get them to open fully while you are washing and wiping them off. Now's a real good time to lubricate all the door hinges and latches including the sliding door. May as well put some oil on the hood hinges and hood latch too.It's not impossible to keep Fords on the road....just tricky......very tricky.

Apr 16, 2009 | 1998 Ford Windstar

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

485 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

76649 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

fordexpert

Level 3 Expert

5537 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...