Question about 1994 Toyota 4Runner
Posted by Anonymous on
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
Here's a link to this great service
Posted on Jan 02, 2017
check with your local Toyota dealer in the parts department and make sure you give them the liter of both engines and they can give you the correct answer and you can also try autozone.com to see if they have your car listed for diagrams pictures and step by step instructions if your car is not listed then try your local library they have all the car manuals and even copy them for you
Posted on Mar 12, 2009
1. Look up along the lower radiator hose. It will plug into a metal
tube on the engine side. Follow the metal tube. It goes to a housing.
The housing is kind of buried in the driver's side of the engine. There
are 2 smaller coolant tubes plugged in above it. You do not need to
touch those, although it looks at first glance like you do.
2. Disconnect lower radiator hose at the metal tube.
3. Disconnect fan switches 1 and 2. These are on elecrtical harnesses going to this housing.
4. Disconnect a sensor on the front of the engine, just above the lower hose. I believe this is the knock sensor, but I'm not sure.
5. Now for the fun part. There are 3 bolts holding this housing on. You can see one at the top. There are 2 others underneath it, such that the bolts form a triangle pattern. You will have to get the bottom 2 out by feel (blind). They are 10mm.
6. Also, if you look to the front of the housing, you will note another 10mm bolt on the front holding down a black plastic leg. This is a wiring harness duct. Remove that bolt. Trace back along the duct. There is one more bolt on the driver's side retaining the duct. There is also one on the back of the engine at the firewall / driver's side. Remove these 2 as well.
7. There is a 12mm bolt holding the metal tube from that housing to the driver's side. Remove that bolt.
8. Gently pry the plastic wiring duct toward driver's side, and back toward firewall. You have just enough to get it off of the stud on the thermostat housing.
9. Now you can pull the housing. It will not come all the way out. It will come loose enough to give you just enough clearance to remove the thermostat (barely). Once you remove the thermostat, you have to pass it downward and toward the firewall to fumble it out.
By the way, you will notice that the metal tube is kind of wiggly in the thermostat housiung. This is normal.
10. Pass the new thermostat in the same way you got the old one out. Make sure when you plug it in that it has an air bleed poppet, and that this poppet is facing up.
11. Reassemble by reversing removal. Getting the nuts / bolts back in blind is... fun...
I don't know the torque spec. You can get a torqure wrench in there barely if you get creative with extensions, knuckles, etc. I wouldn't go abouve 8-10 ft-lb.
Posted on May 01, 2009
its on the driver sidde of the engine. You will see the radiator hose running to the thermostat housing. You must remove the radiator hose and thermostat housing to see it. also make sure your radiator caps seals aren't leaking, especially the one on the top passenger side of the engine!!
Posted on May 10, 2010
Tips for a great answer:
Oct 21, 2014 | 1994 Toyota 4Runner
May 23, 2014 | 1994 Toyota 4Runner
Mar 03, 2012 | 1994 Toyota 4Runner
Oct 16, 2010 | 1994 Toyota 4Runner
Jun 11, 2010 | 1994 Toyota 4Runner
Mar 29, 2010 | 1994 Toyota 4Runner
Jul 31, 2009 | 1994 Toyota 4Runner
May 03, 2009 | 1994 Toyota 4Runner
Jan 16, 2009 | 1995 Toyota 4Runner
370 people viewed this question
Usually answered in minutes!
Step 2: Please assign your manual to a product: