Question about 2006 Land Rover LR3

Open Question

Resetting check brake pads light on 2006 land rover lr3

Posted by Anonymous on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 11 Answers

SOURCE: i do not know how to check transmition oil in my

There is no dipstick for the LR3. A scantool diagnostic piece needs to be used with a laptop to access the transmission computer. The temperature must be between 100 and 110 degrees F. there is a small plug on the right side of the transmission that has to be unscrewed and when you reach 100 degrees the fluid shoud be pouring out. If it needs more is will have to be pumped in. Dexron six works well.

Posted on Jun 23, 2009

  • 333 Answers

SOURCE: How do I change Rear Breaks on 2006 LR3 Land

Brake Pads

Service Repair No - 70.40.03


Removal

  1. WARNING: Brake pads must be renewed in axle sets only, otherwise braking efficiency may be impaired. WARNING: If the brake pad wear warning light has been activated, the pad wear sensor must be replaced. CAUTION:To avoid accidental operation of the Electric Parking Brake (EPB) andpossible damage to the EPB actuator, remove Fusible link 8, located inthe engine compartment fuse box before commencing work. WARNING: Do not work on or under a vehicle supported only by a jack. Always support the vehicle on safety stands. Raise and support the vehicle.
  2. Remove the wheel and tire.
  3. CAUTION: The brake pad wear indicator sensor is easilydamaged. Do not use a lever to remove the sensor. Use fingers only. RHside only: Disconnect the brake pad wear indicator sensor.
  4. Remove the brake caliper lower bolt.
  5. Remove the brake pads.
Installation

WARNING: Do not use compressed air to clean brake components. Dust from friction materials can be harmful if inhaled.

Clean the caliper housing and anchor plate using brake cleaning fluid.
  1. Inspect the caliper piston and slide pin seals for damage.
  2. Position a bleed jar containing a small quantity of approved brake fluid. Connect the bleed tube to the bleed screw and loosen the screw.
  3. Press the piston into the caliper housing.
    • Tighten the bleed screw to 14 Nm (10 ft. lbs.) .
  1. Disconnect the bleed tube and remove the jar.
  2. Install the brake pads.
    • Install the 2 clips.
  1. Rotate the brake caliper downwards.
    • Tighten the bolt to 35 Nm (26 ft. lbs.) .
  1. Connect the brake pad wear indicator sensor.
  2. Repeat the above procedure for the other side.
  3. Install the wheels and tires.
    • Tighten the wheel nuts to 140 Nm (103 ft. lbs.) .
  1. Depress the brake pedal several times, check the fluid level in the brake fluid reservoir and top up with brake fluid if necessary.

Posted on Sep 10, 2009

  • 10865 Answers

SOURCE: how to program a fob for land rover lr3 2005

This link may be of help to you

http://www.keylessride.com/keyfob.asp

Posted on Oct 18, 2009

  • 1 Answer

SOURCE: abs light on in land rover

I have spent way too much money trying to get the 3 amigos to go out...ABS light, TC light and downhill descent. I have decided to try and ID the wires that go to those particular dash lights and cut them. I am tired of this ****. Landrover told me three different things that may cause this issue and told me to start with the least expensive one first! Go to hell, Landrover. I will NEVER buy another Landrover product. Which wires can I cut?

Posted on Oct 20, 2009

ZJLimited
  • 17970 Answers

SOURCE: How to reset the oil service meter-2005 Land Rover LR3

Service light reset – Land Rover PDF File

I hope helps with this (remember rated this help).

Posted on Dec 16, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Brake light


Possibly wrong bulb? Check you havent replaced a single contact bulb with a double contact one. Otherwise check earth to cluster,

Nov 16, 2013 | 2006 Land Rover LR3

1 Answer

My rear brake light is not working but the bulb is new


The replacement lamp could be defective or installed backwards.

Nov 16, 2013 | 2006 Land Rover LR3

1 Answer

How to reset the maintenance meter for 2005 land rover lr3


some of these cars have a plug near the trip meter reset that is pressed with a long narrow object like a thin Philips screwdriver or a knitting needle.

Mar 02, 2012 | 2005 Land Rover LR3

1 Answer

I have a 2006 lr3 i just changed the rotors and pads on the fronts and backs but brake pad warning on the dash wont go away


Did you replace the wear sensors. If the sensors were activated(the light went on) before you changed the pads then the sensor must be replaced

Mar 07, 2011 | 2006 Land Rover LR3

1 Answer

The engine ship came on?land rover LR3 / 2006


That little ship means you are low on coolant, check the overflow bottle for the antifreeze.

Nov 04, 2010 | 2006 Land Rover LR3

1 Answer

My aux inport won't work on 2006 Land Rover LR3. Would this be something effected by a bad fuse?


No. Radio works off single fuse. Some aux ports have to be enabled by mode/source setting. Check your radio manual on how to turn on aux port.

Aug 23, 2010 | 2006 Land Rover LR3

1 Answer

Change a fog light for a 2006 LR3


There is a circular cover surrounding the fog light assembly that simply pops off. Behind that cover there are three maybe four torx style screw that need to be removed, then simply just disconnect the electrical connector to the fog light assembly.

Oct 14, 2009 | 2006 Land Rover LR3

Not finding what you are looking for?
2006 Land Rover LR3 Logo

Related Topics:

103 people viewed this question

Ask a Question

Usually answered in minutes!

Top Land Rover Experts

Colin Stickland
Colin Stickland

Level 3 Expert

22133 Answers

yadayada
yadayada

Level 3 Expert

75807 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8172 Answers

Are you a Land Rover Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...