Question about Cars & Trucks

Open Question

Daewoo forklift how to pull codes ,check engine light on

Runs,has no power,check enging light on,need to know how to pull codes and beable to read them

Posted by on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 186 Answers

SOURCE: Check Engine Light - Tcode P2106

big problem with egr intake passage plugging up need to remove upper intake check passage

Posted on Jul 10, 2008

  • 255 Answers

SOURCE: Check eng , light stays on, goes off, then back on,, lower fuel milage

Hi,If your car have more than 50 k miles ,try oxigen sensor...

Posted on Aug 17, 2008

  • 32 Answers

SOURCE: eng light comes on and code 1887

The code P1887 is an indication of a malfunction with the TCC release switch.
The Torque Converter Clutch (TCC) release switch is part of the Automatic Transmission Fluid Pressure Manual Valve Position Switch (TFP Val. Position Sw.). The TFP Val. Position Sw. is mounted to the transmission valve body. The switch is normally-closed. The switch signals the Powertrain Control Module (PCM) that the TCC is released. This is accomplished by Torque Converter release fluid pressure acting on the switch contact, thus opening the switch. When the voltage is high on the circuit, the Powertrain Control Module recognizes that the TCC is no longer engaged.
When the PCM determines that the TCC release switch is open (indicating that the TCC is not applied) and the TCC slip speed indicates that the TCC is applied, then DTC P1887 sets.

Posted on Oct 11, 2008

  • 1114 Answers

SOURCE: check engine light "reduced enging power" message?

hook it up to OBD 2 scan retrieve fault code and go from that point!

Posted on Dec 24, 2008

  • 25 Answers

SOURCE: need to pull and reed trouble codes for a 1989 honda

there is a jumper wire on the passenger side kick panel, short this wire with a paper clip and turn your ignition to run, the CEL check engine light will flash the number of the trouble code,
long flashes = 10's
short flashes = 1's
so a code read like this
L<L<L<S<S<S<S<S
would be 35
there will be short pauses between flashes and a long pause between separate codes,
hope this helps

Posted on Feb 17, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

I have a Daewoo lanos 2000 mod just over 110000 on the clock and it shudders then the check eng light comes on the shudder is quiet big


replace the timing belt at 60,000 intervals
getting close for its next change

what work has been done for its 110,000 km service

23e769bf-7f14-4277-907e-78d4b2a30d10.jpg

Nov 30, 2016 | Daewoo Cars & Trucks

1 Answer

I have a Daewoo look down to the 2001 I put a new alternator in it and throttle position sensor and it still drains my battery and I lose power would it be the starter and solenoid


It is likely neither the starter nor solenoid. Detecting what is draining power is a pain, start with pulling all the fuses, and see if it's still draining your power.
If so, then it's something that's powered without a fuse (unlikely)
If not, then put fuses in one at a time until the drain is back. Now you know which circuit has the problem. Investigate that.

Loosing power is a totally different issue. You get a "check engine" light? Get the code read.

Jan 16, 2016 | Daewoo Cars & Trucks

1 Answer

Have check eng lite on and no code on scaner, van will start runs terrible. can turn key to on and have fire at dist. without starting and can turn key off and there is still fire at dist. cap have...


if the check engine light is on then there is a code its too old to read with a ob2 scan gun how are you pulling code if the lights on then there is a code

Dec 26, 2010 | 1998 Nissan Quest

1 Answer

Check eng light comes on and then loss of eng power


The check engine light/service engine soon (yellow light) comes only when the computer control unit (called the PCM) senses a fault in the electronic controls of the engine and/or the emission system u will seldom feel the car engine run any different, there are about 200 possible faults that turn the light on, to know what has developed a problem you must have the system tested, this is called an OBD2 fault code test, Kragen and Autozone parts stores do this testing for free.

Sep 25, 2010 | 1999 Ford F350 Regular Cab

2 Answers

1997 Jeep Grand Cherokee 6cyl eng . Runs good, Check Eng light came on and stays on. What do I need to fix and how to reset light if nothing major is happening. Thank you !


go to auto zone or pretty much any car parts place and ask them to read your code they can tell you what it is and reset it for you

Sep 08, 2010 | Jeep Cherokee Cars & Trucks

1 Answer

I have a 2006 trailblazer engine light on when started runs for about 3 sec. then cuts off.


First of all, what cuts out, the "check engine" light, or the engine itself? If its the ck eng light it sounds like an intermittin problem that in most cases cannot be resolved with a code scanner. Have you disconnected the battery to reset that light? If not, then do so (usually the ground cable) for about 10 min., then re-connect the cable and your ck eng. light will be off. ck eng. lights generally have to be constantly on in order to pull codes from the PCM. If there is a problem then the light will come back on.

Mar 31, 2010 | 2005 Chevrolet TrailBlazer

2 Answers

The engine check warning light has just come up on the dashboard of my '02 Lanos - the car seems to be running fine. Got no cash 'till pay-day, can I still use the car 'till I can get it checked out in 10...


yes if the car is running fine.It is probably an emission problem.Take it to the shop to get codes read.Most do it for free.it only takes 10 minutes.this will tell you what is wrong.

Feb 07, 2010 | 2002 Daewoo Lanos

2 Answers

'check engine' comes on


the 1st step to resolve a check eng light is to have the computer control system tested for the trouble/malfunction code that is stored when ever the ck eng lt is turned by the computer on, there are over 200 such trouble codes so guessing is not really an option, have the memory read for the code and post the code back here on fixya.

Jul 24, 2009 | 2007 Maserati Cambiocorsa Coupe

1 Answer

Temp sensor needs to be replaced


this does not mean the sensor is defective, it most likely means the engine thermostat is stuck open and the engine is not running hot enough to satisfy the computers preset temp requirements for minimum eng operating temp.

Apr 08, 2009 | 2002 Daewoo Lanos

1 Answer

Need to pull and reed trouble codes for a 1989 honda


there is a jumper wire on the passenger side kick panel, short this wire with a paper clip and turn your ignition to run, the CEL check engine light will flash the number of the trouble code,
long flashes = 10's
short flashes = 1's
so a code read like this
L<L<L<S<S<S<S<S
would be 35
there will be short pauses between flashes and a long pause between separate codes,
hope this helps

Feb 09, 2009 | 1989 Honda Civic

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

191 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

75005 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...