Question about 1992 Chevrolet S-10

1 Answer

Can not get trouble codes buy jumping terminals according to manu

Check engine lite stays on tried jumping terminals and nothing happens lite does not flash
92 s10 4.3liter 4wd

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 3 Answers

Use code scanner. if not connecting follow wires connected to dtl to find where broken

Posted on Jan 31, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

My 2002 Ford Taurus only clicks when I turn the key. The battery is charged , lights and horn all work well. Thief light blinks.


Your security system is a starter disable type system. You can usually jump the starter motor, for testing, to see if it will crank the engine, even if it will crank that doesn't mean it will start, probably won't if security system is involved.
There are safety issues with jumping the starter, you have to be sure tranny is in park or neutral and parking brake is set. Safety is your responsibility.
Unplug starter relay, use jumper wire on load side of relay between two terminals, the load side is that line with arrow head, one of those terminals is hot all the time.

You can try different key, nothing on key ring except that one key. Check for applicable trouble codes. To check codes yourself, at the least, you need an obd2 code reader that will read manufacturer specific codes as well as p0 codes.

26324029-z0wyzb1eiqut4sudbcxfr354-2-0.jpg

Oct 23, 2016 | 2002 Ford Taurus

1 Answer

Battery dead...cannot get the cargo hatch open without power.


If you jump started and nothing happened then you have a poor connection or your jump leads were too small. You need welding cable size leads and heavy clamp to get the current to a dead car. Leads the size of straw won't do it. Get it connected properly and retry. Try connecting to the starter terminal, then open the trunk, then try from the battery end. A good home mech should be able to work it out.

Nov 03, 2015 | Cars & Trucks

1 Answer

My 95 honda accord won't go past 50 mph


your vehicle is running in "safe mode" or in "limp mode"

do you know how to use a paper clip to jump the 2 terminals and access the honda's OBD1 trouble codes?


Check Engine Light Codes



eric used a piece of wire, but you can use a paper clip

Apr 13, 2015 | 1995 Honda Accord

1 Answer

What terminals on a 2001 toyota tacoma 2.7 liter engine do I jump to access trouble codes?


OBDII will require a code reader. There are no terminals that can be jumped on the ALDL to get trouble codes.

Feb 19, 2015 | 2001 Toyota Tacoma

1 Answer

ABS light comes on... but no noticble degradation in operation etc.


Most likely a wheel speed sensor, hopefully... The only thing that will change when the ABS light is on is that the ABS will not function as long as the indicator is on. I hope this info helps.

When the airbag system is in functioning condition, the airbag warning light will remain on for about 7 seconds and go out when the ignition switch is set to ON .

If there is any malfunction, the airbag warning light will either stay on or off continuously. In such cases, perform on-board diagnostic in accordance with the specified procedure to determine trouble codes.


  1. Turn ignition switch ON (with engine OFF ).
85091723



  1. Connect DIAG. terminal to No.2 terminal of diagnosis connector located inside lower cover.
  2. Check in accordance with the trouble code indicated by the AIRBAG warning light, and record the trouble codes.
  3. Turn the ignition switch "OFF " and remove the DIAG. terminal from No.2 terminal of diagnosis connector.
85091724


HOW TO READ TROUBLE CODES
The ABS lamp flashes a code corresponding to the faulty parts.

The long segment (1.2 secs on) indicates a "ten", and the short segment (0.3 secs on) indicates a "one".





NOTE: This is the only information provided by the manufacturer for clearing diagnostic trouble codes.

97511505


CLEAR MEMORY
After eliminating problem as per trouble code, clear memory as follows:

Make sure ignition switch is ON (and engine off). Connect one DIAG. terminal (1) on diagnosis connector (2) terminal No.1.

where warning light is flashing, connect the other DIAG. terminal (3) on terminal No. 2 for at least three seconds . After memory is cleared, normal warning light flashing rate resumes. (Warning light flashes every 0.6 seconds (ON-OFF operation.) Memory cannot be cleared if any problem exists.

After clear memory and then DIAG. terminals (1) and (3), extract from diagnosis connector (2)

Jul 27, 2011 | 1999 Subaru Legacy

2 Answers

2006 honda accord wont start. nothing happens when i turn it on, just a click. radio, lights and door chime work.vehicle will not jump start


First make sure the shift lever is properly in the park position. Hondas tend to have little problem in that area after a few years.
Second make sure battery terminals are clean and secure. Next you should try jumping the battery. A low battery may produce enough electricity to run the radio, lights, chimes etc but not enough to crank engine.

Apr 10, 2011 | 2006 Honda Accord

2 Answers

2001 PT Cruiser turn key to start nothing, no power, lites etc... I jump start it and it starts right up. turn off and try to re start, nothing. jump started again fired right up, while running tested...


common car for starter problems hit the starter with a hammer while someone trys to start it if this works it is ure starter, if not the stater and neutral safety switch needs tested

Oct 14, 2010 | 2001 Chrysler PT Cruiser

1 Answer

How do i check my engine trouble codes on a 1994 COROLLA


take it to advanced auto parts. they will hook a computer up to your car for free and tell you the codes. you dont need to be jumping anything

Apr 20, 2010 | 1994 Toyota Corolla

2 Answers

91 accord when turn key to start NOTHING HAPPENS,has new battery,lites come on, checked fuses under hood, NO CLICK SOUND . PLEASE HELP 48 AND DISABLED NEED TRANSPORTION


It could be the neutral safety switch,or the ignition switch,if it is a manual transmission,then it could be the clutch safety switch,on the clutch pedal.

Mar 16, 2010 | 1991 Honda Accord

1 Answer

Check engine and d4 lights on


d4 is flashing as a trouble code for the automatic transmission... i would say without research that it is a code for a transmission solenoid. maybe while washing the car some water got in and caused a short...these solenoids are usually weatherproof....you could try disconnscting the battery for 30 secs..to clear the trouble code and then start the car. remember you may lose your preset info!

Oct 17, 2008 | 1992 Honda Accord

Not finding what you are looking for?
1992 Chevrolet S-10 Logo

Related Topics:

93 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

70387 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22041 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6880 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...