Question about 2002 Ford Explorer

1 Answer

Replaced fuel pump and truck won't start

Posted by on

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

  • Contributor
  • 46 Answers

There is a fuel pump module electrical piece associated with powering up the pump. Most generally they are located on the frame just behind spare tire. when looking from the rear of the vehicle. Sometimes these corrode and cause the symptoms to be the same as bad fuel pump. Hope this helps.

Posted on Jan 16, 2013

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get 2 Free calls (no credit card required) and instant help on almost anything you can think of (from cars to computers, appliances, handyman, and even pets).
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
kephart_robe
  • 31 Answers

SOURCE: 1991 F150 5.0L, The fuel pump relay clicking

check your relay and your fuel filter should be replaced every 30,000 miles

Posted on Mar 18, 2010

Testimonial: "Thank you for your help! Truck decided to run good today!"

  • 65 Answers

SOURCE: front right side hit . replaced concerter and

The new 2010 Fusion has what Ford calls, "one touch" start. If you turn the key to the start position and let go, the starter continues to turn. The ECM takes over the starting process and monitors the number of times the crankshaft rotates as it adds fuel and ignition for the engine to start. On 2010 Fusion's built before August 2009, there is a problem with the starting process. On occasion, the starter will turn the engine, but the engine will not start. The starter will not time out and the only way to stop the starter is to turn the key to the "off" position. TSB 09-19-1 is supposed to take care of the issue by replacing the ground cable with one that has a capacitor in it. Fusion owners with the no-start/intermittent start issue can go to their dealers with the TSB. I have tried to write down some simple tips that may help you to find out why your car won't start. These tips may also prevent you from being overcharged by dishonest mechanics - you will often be charged more at a garage if you look unfamiliar with the car mechanical aspects.
It's frustrating when your car won't start - this happened at least once to most of the drivers. I had situations when my car won't start many times. But no need to panic. The process that goes on since the moment you took the keys out of your pocket to the point where the engine is running is a fairly simple one and it involves few steps.


The engine computer uses the signals from the crankshaft and camshaft position sensors to know which cylinder is in the compression cycle. If either of the sensors is bad, the car won't start. Similarly, if the timing belt, chain or gears are broken, the camshaft won't turn and the engine won't start

The fuel pump starts running, building up the fuel pressure in the fuel injector rail. The engine computer alternatively opens electronic fuel injectors that spray short bursts of gasoline vapors into the intake manifold (or in case of the direct injection, straight into the cylinders). If the fuel pump is bad, the car won't start.



.








.


























Posted on May 17, 2011

oberkiuler
  • 51 Answers

SOURCE: my ford expedition won't start i change the fuel

If it a diesel then you must be aware that when changing a filter and pump they must be full of fuel, otherwise it won't **** the fuel into the engine.

Posted on Jul 11, 2011

  • 5370 Answers

SOURCE: Car will turn over but won't start. Through the

No noise from fuel pump when you turn over the car .First thing get voltage at fuel pump relay checked, is there 12 volt to the relay.If no, then problem is again the relay.--------- To reconfirm the problem, try other test, that is remove the relay and by pass the relay terminals with a jumper wire .Then with 12 volt external battery give power to fuel pump connector and see, if the fuel pump starts, then its clear that fuel pump relay is faulty.----------- Also other problem can be fuel pump inertia switch.If the inertia switch is faulty then also fuel pump will not start.-------- The fuel pump relay on a 1995 Ford Explorer is in the power distribution
box, in the engine compartment, driver's side near the firewall.----------
The fuel pump inertia switch is in the right front passenger area
it is below the dash but above the carpet in the right hand corner.--------
Its a push button type inertia switch.
--------
Fuel Pump Activation
When ignition switch is turned to START position, PCM operates fuel pump relay to provide fuel for starting engine. PCM senses engine speed and shuts off fuel pump by opening ground circuit to fuel pump relay when engine stops or engine speed drops to less than 120 RPM. When ignition switch is in ON position, EEC power relay is energized (contacts closed). Power is provided to fuel pump relay and timer in PCM. Fuel pump receives power through fuel pump relay contacts.
Inertia Fuel Shutoff (IFS) Switch
All models use an electrical interrupt switch in fuel system. During a collision or vehicle rollover, electrical contacts within inertia switch open, shutting off fuel supply to electric fuel pump. Fuel supply is interrupted even when engine is running.
A reset button is located on switch assembly. If electrical circuit trips, vehicle will not restart until switch is reset. Fuel system should be inspected before resetting switch.
IFS switch is located under instrument panel, near right side of transmission hump.
----------- If the fuel pump relay, the inertia switch and fuel pump all checked ok, and fuel pump is working with direct 12 volt source to fuel pump.Then problem relates to computer.The computer (power control module, PCM) is faulty and has to be replaced.--------- This will help.Thanks.Helpmech.

Posted on Jul 17, 2011

Testimonial: "Thanks. That was the best answer yet.I didn't want to hear that the PCM might need to be replaced but the car has served it's purpose through the year"

  • 2006 Answers

SOURCE: car won't start; mechanic said it was fuel

When you changed your fuel pump did you also change the fuel filter? If not, that would be the next logical step. While you have it disconnected you can also check to make sure the fuel pump is pumping the fuel.

Posted on Aug 18, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Was frozen now thawed w/ new fuel filter still won't start


Fuel pump may have ailed this time.. You need to have fuel pump checked.

Jan 31, 2013 | 2000 Ford Explorer Eddie Bauer

1 Answer

My 2004 chevy venture won't start. Changed the


Did the fuel pump come on?

Did you check fuel pressure at the motor?


Try jumping the relay to get pump on?

Read a wiring diagram-- so you know what your doing?

Check Power & Grounds to pump when the tank was down?

Dec 22, 2012 | Cars & Trucks

1 Answer

Engine turns over, but won't start.


No you can check the fuel pump relay, then the fuel pump for ground
& then replace it or have a shop do the job of finding the problem

Nov 24, 2012 | 2001 Ford Taurus

1 Answer

Car cranks but won't start. Already replaced fuel pump & filter


I was told that some fuel pumps do not work more than a day or two, replace the fuel pump again. Mine came with a warrenty

Nov 05, 2012 | 1999 Lincoln Continental

1 Answer

1995 ford contour cranks but won't start, change fuel filter, fuel pump, and spark plugs. Not getting any spark.


Have you ever heard of testing before replacing parts ? Fuel pressure an flow tesing , testing the electrical circuit for the fuel pump , amp draw testing , voltage drop testing etc... Thier are no magical fixes in auto repair . No spark ! check B+ voltage an ground circuits for the ignition system , Ignition System Designs Operation and Testing an SD Premium video

Jun 18, 2017 | 1995 Ford Contour

1 Answer

2000 jeep wrangler won't start, good crank, no bus


Check fuses first, but could be needs new CPU

Jun 14, 2012 | 2000 Jeep Wrangler

1 Answer

2002 chevy silverado won't start, replaced fuel pump, still won't start


Same problem here, found break in wiring harness at cross-member behind cab. did have bed removed for easy access. Ground wire guilty party.

Dec 18, 2011 | 2002 Chevrolet Silverado

1 Answer

Hello. My 1997 Chevy Tahoe refuses to start. The problems began with a bad fuel pump. I changed. It worked. The fuel pump died again. I changed it again and it has been working. I parked it for two weeks....


Now you have a good battery & a starter that turns over the motor

Have you cycled the key on & off with a fuel pressure gauge on the
fuel rail?

Do you have a fuel filter that isn't over 3 or 4 years old?

Have you checked for spark while cranking ? Use an old plug on the wires,
if you have ignition wires,don't ground the wire without resistance

If you removed the ducting & MAF Sensor it won't start

Tell us what you checked & exactly how that was done.

Jun 09, 2011 | 1997 Chevrolet Tahoe

Not finding what you are looking for?
2002 Ford Explorer Logo

180 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

76630 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

fordexpert

Level 3 Expert

5537 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...