Question about 1998 Ford Mustang

1 Answer

Control for windows and mirrors do not pespond.

All feeds into switch have power.

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 12 Answers

It sounds like switches are bad

Posted on Jan 24, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Dodge intrepid runs shut off. Started after I changed the window and mirror switches.


sounds wierd but if you explained this correctly, that when mirrors or dis connected car will shut off, if this is correct then there is a short back feeding power to the ignition or computer keeping the engine running, check the wiring going to mirrors and see if there are shorted wires, this is where i would start

Dec 01, 2013 | Cars & Trucks

2 Answers

Doorlocks dont work except from passenger side. mirrors dont work. windows dont work from anywhere


First, check all fuses to make sure that none are blown.

If the door lock switch works on the passenger side, then the drivers side door lock switch is probably faulty. Use a multi-meter to test the Drivers Side Door Lock Switch (Black and Pink/Light Green wires unlock the vehicle, and the Black and Pink/Yellow wires lock the vehicle)
If the switch is tested and found to be operating properly, you may have a faulty Body Security Module or Drivers Side Door Lock Actuator.

If neither of your Power Mirrors are working, you probably have a faulty Exterior Rear View Mirror Switch, Power Mirror Module, or blown Central Junction Box Fuse.

If none of your Power Windows are working, you probably have a faulty Accessory Delay Relay or a blown fuse in your Central Junction Box or a faulty Master Window Adjust Switch (all of the Power Window Switches feed through this Master Window Switch). If the Power Windows didn't stop working at the same time, you may have faulty Window Adjust Switches, or faulty Power Window Motors, this is very unlikely though. It would also be a good idea to inspect the wiring for any obvious damage.

Mar 15, 2011 | 2005 Ford F-150

1 Answer

I need instructions, written and hopefully with photo examples, that will teach me how to replace the passenger side mirror on my Ford Sport Trac. The truck is a 2004 model and the mirror is motorized...


Removal and Installation
NOTE: LH door is shown, RH door is similar.
  1. Disconnect the battery. For additional information, refer to Section 414-01.
  1. Remove the front door window control switch panel and trim covers.
    1. Remove the door screw cover.
    1. If equipped with power windows, remove the door window control switch and disconnect the electrical connectors.
    1. Remove the door handle bezel
ganyapr_2.jpg
3. Remove the door handle screws


ganyapr_3.jpg
  1. If not equipped with power windows, remove the screw and the window regulator handle.
  1. Remove the screws and the front door trim panel.
ganyapr_4.jpg6. Remove the door speaker Remove the screws.
Disconnect the electrical connector.
Remove the door speaker.
7. Disconnect the exterior rear view mirror electrical connector
ganyapr_5.jpg
8. Remove the nuts and the exterior rear view mirror.
Feed the power mirror wiring through the opening in the front door.
ganyapr_6.jpg
9. To install, reverse the removal procedure

i hope that this could help you
2010&c18=modelyear&c20=n712771&c35=wsm%2cfront%20door%20trim%20panel%2cs5r%2c501-05%2cremoval%20and%20installation&s=1280x800&c=32&j=1.3&v=y&k=y&bw=931&bh=469&ct=lan&hp=n&[aqe]

Feb 20, 2011 | Ford Explorer Sport Trac Cars & Trucks

1 Answer

Need the fuse panel layout for the panel by the passenger door [ just bought truck, panel cover missing. so we canttell which fuse runs what???



1994 Jeep Grand Cherokee Laredo
(Fuse Block - Passenger side of Dash)
1 5 9 13 17 21 25
20 A 15 A 20 A 20 A 7.5 A 15 A 30 A
2 6 10 14 18 22 26
15 A 15 A 10 A 20 A 15 A 15 A 30 A
3 7 11 15 19 23 27
20 A 15 A 15 A 3 A 15 A 15 A 10 A
4 8 12 16 20 24 28
15 A 15 A 15 A 20 A 10 A 7.5 A 30 A

1)Trailer Tow Relay 18)Airbag Module
2)Brake Lamps 19)Interior Mirror, Auto
3)Hazard Lamps Headlamps, Overhead
4)Security Lamp Console, VIC/GDM Module,
5)Interior Lighting Heated Rear Window Relay
6)Security Alarm Module Coil, Illuminated Entry Relay
7)Security Alarm Relay, and Chime Module
Security Alarm Module, 20)Heated Rear Window
Flash-to-Pass Switch, Overdrive Switch,
8)Overhead Console, Keyless Speed Control
Entry, Radio Memory/Clock 21)Security Alarm Module,
Memory/Chime Module, Lamp Outage Module
Power Locks, Power Mirrors, 22)Airbag Module,
HEVAC and VIC Speedometer, Tachometer,
9)Rear Wiper Telltales and Gauges
10)Radio 23)Heated Mirror Feed, Heated
11)Cigar Lighter Rear Window Switch
12)Parking Lamps, Automatic 24)Instrument Panel
Headlamps Illumination
13)Horn Relay 25)Power Seats
14)Power Lock Relays 26)Power Windows, Power
15)ABS Module and Relay Sunroof
16)Turn Signals 27)Security Alarm Module and
17)Heating and Air Front Wiper
Conditioning Module 28)Heated Rear Window Relay

Aug 20, 2010 | 1994 Jeep Grand Cherokee

1 Answer

94 grand cherokee fuse panel fuse id,,,need to know each fuse function, location in panel and amp


............1994 Jeep Grand Cherokee
......(Fuse Block - Passenger side of Dash)
.....1........5........9........13........17........21........25
..20 A...15 A...20 A....20 A....7.5 A.....15 A....30 A
.
.....2........6.......10.......14........18........22........26
..15 A...15 A...10 A....20 A.... 15 A.....15 A....30 A
.
.....3........7.......11.......15........19........23........27
..20 A...15 A...15 A.....3 A......15 A....15 A.....10 A
.
.....4........8.......12.......16........20........24........28
..15 A...15 A...15 A....20 A.....10 A....7.5 A....30 A
1)Trailer Tow Relay
2)Brake Lamps
3)Hazard Lamps
4)Security Lamp
5)Interior Lighting
6)Security Alarm Module
7)Security Alarm Relay, Security Alarm Module, Flash-to-Pass
8)Overhead Console, Keyless Entry, Radio Memory/Clock
Memory/Chime Module, Power Locks, Power Mirrors,
HEVAC and VIC
9)Rear Wiper
10)Radio
11)Cigar Lighter
12)Parking Lamps, Automatic Headlamps
13)Horn Relay
14)Power Lock Relays
15)ABS Module and Relay
16)Turn Signals
17)Heating and Air Conditioning Module
18)Airbag Module
19)Interior Mirror, Auto Headlamps, Overhead Console,
VIC/GDM Module, Heated Rear Window Relay Coil,
Illuminated Entry Relay and Chime Module
20)Heated Rear Window Switch, Overdrive Switch, Speed Control
21)Security Alarm Module, Lamp Outage Module
22)Airbag Module, Speedometer, Tachometer, Telltales and
Gauges
23)Heated Mirror Feed, Heated Rear Window Switch
24)Instrument Panel Illumination
25)Power Seats
26)Power Windows, Power Sunroof
27)Security Alarm Module and Front Wiper
28)Heated Rear Window Relay

Aug 19, 2010 | 1994 Jeep Grand Cherokee

3 Answers

2004 ford expedition eddie bower


For the rear window, just need adjuts the both slightly...


Check the next procedure to Power Mirrors...

Diagnosis & Testing

The exterior mirror control switch receives power through circuit SBP12 (GN/RD) and ground through circuit GD143 (BK/VT). The exterior mirror control switch uses circuit CPM23 (GY) as the common circuit for both exterior mirror up/down and right/left movement.
  1. Possible Causes:
    Fuse 12 (7.5A) (SJB) An open in circuits CPM23 (GY), SBP12 (GN/RD) or GD143 (BK/VT A short to ground in circuit CPM23 (GY) A short to voltage in circuit CPM23 (GY) Exterior mirror control switch.
  2. Checking the voltage at the mirror switch:
    Key in OFF position. Disconnect: Exterior Mirror Control Switch C527. Key in ON position. Measure the voltage between ground and exterior mirror control switch C527-1, circuit SBP12 (GN/RD). Voltage should be greater than 10 volts.
  3. If voltage is greater than 10 volts, check that fuse 12 (7.5A) is OK. If OK, REPAIR circuit SBP12 (GN/RD) for an open.

Exterior Mirror Motor Synchronization

NOTE This procedure must be performed any time the power folding mirrors are manually folded in or out, or if the position of the mirror case has been moved without using the mirror control switch.
NOTE If the power folding mirrors are folded or unfolded continuously (6 to 10 cycles), the power lockout feature will disable the system for 2 minutes to prevent damage to the power fold motors. After 2 minutes have elapsed, normal operation will resume.
  1. Set the mirror control switch to the CENTER position.
  2. Use the mirror control switch (press rearward) to automatically cycle the power folding mirrors in and out 4 times.
  3. When an audible popping sound is heard, the power folding mirror motors are synchronized.
    NOTE It may be necessary to cycle the power folding mirrors in or out up to 4 times before they are synchronized.

Removal & Installation
Motor
  1. Before servicing the vehicle, refer to the precautions section.
    NOTE If equipped with power folding mirrors, they must be synchronized any time the mirrors have been folded or unfolded without using the mirror control switch. Refer to synchronization procedure.
  2. Position the exterior mirror glass in a downward position to obtain a gap at the edge of the mirror.
    CAUTION Place a shop towel between the exterior mirror glass and the hand to avoid personal injury in the instance of glass breakage.
  3. Insert a flat-blade screwdriver between the mirror glass tabs and the mounting plate, and rotate to separate the locking tabs from the mounting plate.
  4. Carefully pull the top edge of the glass away from the exterior mirror housing.

    0996b43f802029e0.jpg Fig. Mirror Glass removal shown
  5. If equipped, disconnect the heated mirror electrical connectors and remove the glass.
  6. Remove the 3 exterior mirror motor screws and exterior mirror motor.
  7. Disconnect the electrical connectors.
  8. To install, reverse the removal procedure.

Switch
Expedition Trim Panel Removal

NOTE The door glass must be completely raised.
  1. Remove the window control switch plate.
  2. Remove the door handle bezel.
    WARNING To avoid damage to the door trim panel, lift the door trim panel by pulling directly upward on the armrest to disengage the panel clips.
  3. Remove the two bolts and three screws, and remove the door trim panel.
  4. Remove the finish cover to access the two center screws.
  5. Disconnect the electrical connectors. Navigator Trim Panel Removal
  6. Remove the door handle bezel.
  7. Use service notch.
    WARNING To avoid damage to the door trim panel, lift the door trim panel by pulling directly upward on the armrest to disengage the panel clips.
  8. Remove the two bolts and three screws, and remove the door trim panel.
  9. Disconnect the electrical connectors.
  10. Depress the locking tabs and remove the exterior mirror control switch.
  11. Remove the exterior mirror control switch.

If you dont want waiting more time for the Owners Manual, can check here this choice 2004-Ford-Expedition-Owners-Manual

Hope this help.

Apr 23, 2010 | 2004 Ford Expedition

2 Answers

Fusebox diagram


hi, this is courtesy of ask me help desk...

FUSE PANEL INTERIOR

1 - 20 Amp (Yellow)Power Antenna Relay, Trailer Tow Relay.

2 - 15 Amp (Blue) Brake Lamps.

3 - 20 Amp (Yellow) Hazard Lamps.

4 - 15 Amp (Blue) Security Lamp.

5 - 15 Amp (Blue) Interior Lighting.

6 - 15 Amp (Blue) Security Alarm Module.

7 - 15 Amp (Blue) Security Alarm Relay, Security Alarm Module, Flash-To-Pass.

8 - 15 Amp (Blue) Overhead Console, Keyless Entry, Radio Memory, Clock/Chime Module, Power Locks, Power Mirrors, HVAC & VIC.

9 - 20 Amp (Yellow) Rear Wiper.

10 - 15 Amp (Blue) Radio Accessory.

11 - 15 Amp (Blue) Cigar Lighter.

12 - 15 Amp (Blue) Parking Lamps, Automatic Headlamps.

13 - 20 Amp (Yellow) Horn Relay.

14 - 20 Amp (Yellow) Power Lock Relays.

15 - 3 Amp (Violet) ABS Module & Relay.

16 - 20 Amp (Yellow) Turn Signals.

17 - 7.5 Amp (Brown) Heater & Air Conditioning Module.

18 - 15 Amp (Blue) Air Bag Module.

19 - 15 Amp (Blue) Interior Mirror, Auto Headlamps, Overhead Console, VIC/GDM Module, Heated Rear Window Relay Coil, Illuminated Entry Relay & Chime Module.

20 - 10 Amp (Red) Heated Rear Window Switch, Overdrive Switch, Speed Control.

21 - 15 Amp (Blue) Cluster, Security Alarm Module, Lamp Outage Module.

22 - 15 Amp (Blue) Air Bag Module, Speedometer, Tachometer, Telltales, Gauges.

23 - 15 Amp (Blue) Heated Mirror Feed, Heated Rear Window Switch.

24 - 7.5 Amp (Brown) Instrument Panel Illumination.

25 - 30 Amp Circuit Breaker Power Seats.

26 - 30 Amp Circuit Breaker Power Windows.

27 - 10 Amp Circuit Breaker Security Alarm Module, Front Wiper.

28 - 30 Amp Circuit Breaker Heated Rear Window Relay

Nov 27, 2009 | 1993 Jeep Grand Cherokee

1 Answer

1996 grand cherokee has no power to drivers door controls.Locks mirrors windows


The master switch on the drivers door, the one that controls all of the windows, locks, and mirrors, is notorious for going bad. There are a few complaints in blogs out there. You can find one online, at eBay or junkyard. Or pay the big money at the dealer. I have fixed a handful of these. You can use a multimeter to measure voltage feeding into the switch at the harness. You should have about 12+ volts on the hot lead.

Apr 20, 2009 | 1996 Jeep Grand Cherokee

1 Answer

My side mirros dont work


The exterior mirrors:
  • are controlled by power controls on the LH front door trim panel.
  • are of a foldaway design.
  • may contain turn signal indicators.
  • may be heated when the heated back window glass is activated.
  • may have a programmable recall memory option.
Driver Seat Module
The power driver seat and power exterior mirrors are controlled by the driver seat module (DSM) only when the vehicle is equipped with the programmable/recall memory option.
---------------------------------------------------------------------
Power Exterior Mirror Operation
The power exterior mirrors are controlled by the DSM and are operational all the time, whether the ignition switch is on or off. Using the power exterior mirror switch, the driver can adjust the driver and passenger exterior mirrors four ways.
-----------------------------------------------------
Visual Inspection Chart Mechanical Electrical
  • Exterior mirror(s)
  • Interior mirror
  • Central junction box (CJB) fuse
  • Circuitry
  • Exterior mirror control switch
  • Exterior mirror motor
  • Interior mirror
  • Driver seat module (DSM)
  • Memory set switch


----------------------------------------------------------------------------------


  1. If the vehicle is equipped with memory exterior mirrors and the concern remains after the inspection, connect the diagnostic tool to the data link connector (DLC) located beneath the instrument panel. Select the vehicle to be tested from the diagnostic tool menu.
    • Check to make sure the program card is correctly installed.
    • Check the connections to the vehicle.
    • Check the ignition switch position.
-------------------------------------------------------------------------------------
  • The mirrors are inoperative
  • Circuitry.
  • Central junction box (CJB) fuse.
  • Exterior mirror control switch.


Apr 07, 2009 | 2003 Lincoln Navigator

Not finding what you are looking for?
1998 Ford Mustang Logo

Related Topics:

37 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

60769 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Fordexpert

Level 3 Expert

5331 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...