Question about 2004 Ford Freestar

1 Answer

Radio removal removing radio

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Sergeant:

    An expert that has over 500 points.

  • Expert
  • 274 Answers

Get a haynes repair manual at your local auto parts store or on ebay

Posted on Jan 16, 2013

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I have a 2002 mercury mountaineer, V6 4.0 2WD. Where is the GEM located?


Module - Generic Electronic (GEM)/Central Timer (CTM) Removal
  1. CAUTION: Electronic modules are sensitive to static electrical charges. If exposed to these charges, damage may result. Depower the supplemental restraint system (SRS). For additional information, refer to Section 501-20B .
  1. Remove the audio unit. For additional information, refer to Section 415-01 .
  1. Remove the center instrument panel finish panel.
    1. Remove the screws.
    1. Remove the center instrument panel finish panel.
    • Disconnect the electrical connectors.
    • Remove the GEM/CTM.
      1. Remove the screw.
    1. Disconnect the four connectors from the GEM/CTM.
    1. Remove the GEM/CTM.
    2. Installation
      1. NOTE: When the battery is disconnected and reconnected, some abnormal drive symptoms may occur while the vehicle relearns its adaptive strategy. The vehicle may need to be driven 16 km (10 mi) or more to relearn the strategy.
Special Tool(s) Radio Removing Tool
415-001 (T87P-19061-A) Removal
  1. Remove the radio chassis.
    1. Insert Radio Removing Tool into the radio face plate and release the radio retaining clips.
    1. Pull outward on Radio Removing Tool to remove the radio chassis from the instrument panel.
    2. Remove the radio.
      1. Disconnect the electrical connectors.
      1. Disconnect the radio antenna lead in cable.
      1. Remove the radio.

May 26, 2017 | Mercury Cars & Trucks

1 Answer

How do i remove the stock radio from my 1993 geo metro 4 door hatchback


here is the online fsm quote

  1. Disconnect the negative battery cable.
  2. Open the glove box. Remove the glove box open panel.
  3. Remove the air conditioning switch connector and heater control unit lever knobs. Pull heater control unit cover plate from instrument panel.
  4. Remove the gearshift control lever upper boot and center console.
  5. Remove the ashtray.
  6. Remove the instrument panel center trim bezel and radio face plate.
  7. Remove the screw from the back of the radio receiver and the screws from the front face of the radio.
  8. Remove the radio.

Sep 30, 2014 | 1993 Geo Metro

1 Answer

How do you remove the stereo from a Toyota Echo?


NOTE: The following procedure may vary a bit from the system which you have in your car.
TO REMOVE RADIO RECEIVER ASSEMBLY
(a) for Integrated with Panel:
(1) Disconnect the hazard warning signal switch
connector.
(2) Remove the 4 bolts.
(3) Disengage the 4 clips and the 4 claws and
remove the radio receiver.
(4) Disconnect the plug.
(5) Disconnect the 3 radio connectors.
(b) except Integrated with Panel:
(1) Remove the 4 bolts and the radio receiver.
(2) Disconnect the plug.
(3) Disconnect the 2 radio connectors.
1. REMOVE INSTRUMENT PANEL CENTER REGISTER
ASSEMBLY (for Integrated with Panel)
2. REMOVE RADIO BRACKET RH
(a) for Integrated with Panel:
(1) Remove the 4 screws and the radio bracket.
(b) except Integrated with Panel:
(1) Remove the 4 screws and the radio bracket.
3. REMOVE RADIO BRACKET LH
HINT:
Use the same procedure as for the RH side.

Feb 14, 2014 | 2001 Toyota Echo

2 Answers

I need to remove my 6 cd changer am fm radio how does ut come out please help so i can replace it


you need the radio removal u shaped tools. you can buy for $5 at uto store.

SECTION 415-01: Audio Unit 2002 Escape Workshop Manual
REMOVAL AND INSTALLATION Audio Unit
Special Tool(s) s2k~us~en~file=st1445a.gif~gen~ref.gif Radio Removing Tool
415-001 (T87P-19061-A)
Removal and Installation
  1. Disconnect the battery cables. For additional information, refer to Section 414-01 .
  1. Remove the audio unit.
    1. Insert the special tool into the radio face plate and release the radio retaining clips.
    1. Pull outward on the special tool and remove the audio unit from the instrument panel.
  1. Disconnect the connectors.
  1. To install, reverse the removal procedure.

Apr 22, 2011 | 2002 Ford Escape

2 Answers

How do i remove the factory radio on my 1983 cadillac fleetwood


Hi there,

Locate and remove two (2) phillips screws that secure the top of the plastic panel that surrounds the radio. The plastic dash panel will pull off once the screws are removed as shown in the photo above.
The front of the radio is held in with two (2) 7mm bolt screws at the top of the radio. Remove the 2 bolt screws.
There is a hidden radio that secures the rear of the radio and is located under the radio. Pull the ashtray to its extended position. You will need to lay on your back or side and look behind the ashtray, up to the bottom of the radio.
Once the ashtray has been pull to its extended position, you should be able to locate and remove one (1) 7mm bolt screw as seen in the photo above.
Once all screws have been removed, the radio can then be removed. Pull firmly on the radio to remove it from the dash. The radio will most likely resist pulling from the dash. The antenna cable which plugs into the rear of the radio is very short and gives the radio resistance when trying to pull the radio out of the dash. Continue to pull firmly and the antenna cable will unplug itself as the radio is pulled from the dash.
Unplug (1) blue, (1) white, and (1) black wire harness connector(s) from the rear of the radio. There will also be wires extending from the rear of the radio with a plastic connector attached to the wires about 4 inches from the rear of the radio. Unplug this small connector. The radio can now be completely removed from the dash. Set it aside. You will need to remove the plastic brackets attached to the top and bottom of the GM radio. This will be shown in detail in the "Mount New Radio" section.

Hope these helps....

Jan 23, 2011 | Cadillac Fleetwood Cars & Trucks

1 Answer

Removal of radio


Radio Reciever/Amplifier/Tape Player/CD Player REMOVAL & INSTALLATION Fig. 1: Remove the bezel retaining fasteners and the bezel . . . 86746p02.jpg
  1. Disconnect the negative battery cable.
  2. Remove the center cluster screws and bezel.
  3. Remove the radio attaching screws.
  4. Disconnect the radio from the instrument panel wiring harness and antenna.
  5. Installation is the reverse of removal. Fig. 2: . . . then remove the radio retaining fasteners 86746p12.jpg
    Fig. 3: Slide the radio forward so that you may gain access to the electrical connections 86746p13.jpg
    Fig. 4: Disengage the antenna and radio electrical connections 86746p14.jpg
prev.gif next.gif

Oct 17, 2010 | 1993 Jeep Grand Cherokee

1 Answer

REMOVAL OF THE RADIO


Here ya go!

4c47b30.gif
Exploded view of the radio, tape player or CD player removal, 1990-94 vehicles

  1. Disconnect the negative battery cable. Wait at least 60 seconds before beginning the remainder of the procedure, in order to disarm the Supplemental Restraint System (SRS).
  2. Using a plastic trim tool, remove the radio panel. Pry the lower part of the radio panel away first, then separate and remove the panel.
9d61d07.gif
Using a plastic trim tool, carefully pry the radio trim panel away

08e17de.gif
Remove the center trim panel for access to the radio retainers

WARNING When removing and installing the floor console, do NOT allow it to bump against the SRS-ECU!

  1. For 1995-98 vehicles, remove the floor console assembly, as outlined in Section 10 of this manual.
  1. Remove the mounting bolts and pull the radio receiver, tape player or CD player out slightly. Detach all harness connectors and remove the unit from the vehicle.
4c48f2d.gif
After removing the console, unfasten the radio mounting screws

e7143a0.gif
Pull the radio out enough to access the connectors

4cb0996.gif
Unplug the electrical connector from the rear of the radio ...

3795675.gif
... then disconnect the antenna lead and remove the radio from the vehicle


Installation is the reverse of the removal procedure.

Oct 29, 2009 | 1992 Eagle Talon

1 Answer

I need to remove the radio in my 1998 mountaineer


you need specail radio removal tools. they spread 4 spring clips.

  1. Remove the radio chassis.
  2. Insert Radio Removing Tool into the radio face plate and release the radio retaining clips.
  3. Pull outward on Radio Removing Tool to remove the radio chassis from the instrument panel.
Special Tool(s)

Radio Removing Tool
415-001 (T87P-19061-A)

19701bc.gif

May 12, 2009 | 1998 Mercury Mountaineer

1 Answer

I need to change the bulb in the analog clock in my 1999 Lincoln Towncar. How do I go about getting to it without tearing apart the dashboard?


you need a special tool to get the radio out. It has pins that spread out spring clips so the radio can pull out.

please rate as solved if this helps.

SECTION 413-00: Instrument Cluster and Panel Lighting — General Information 1999 Town Car Workshop Manual
REMOVAL AND INSTALLATION Bulb —Electric Clock
Special Tool(s) Radio Removing Tool
T87P-19061-A

2242b54.gif
Removal
  1. Disconnect the battery ground cable.
  1. Pull out the radio using Radio Removing Tool.
1475891.gif
  1. Remove the radio.
    1. Disconnect the electrical connectors.
    1. Disconnect the antenna cable.
    1. Remove the radio.
  1. Remove the instrument cluster finish panel bolts.
c7eab47.gif
  1. Remove the instrument cluster finish panel bolts.
054ed10.gif
  1. Pull out and position aside the instrument cluster finish panel.
cc71028.gif
  1. Disconnect the electric clock electrical connector.
  1. Remove the instrument cluster finish panel.
    1. Disconnect the headlight switch electrical connector.
    1. Disconnect the dimmer switch electrical connector.
    1. Remove the instrument cluster finish panel.
  1. Remove the electric clock illumination bulb.

Apr 23, 2009 | 1999 Lincoln Town Car

3 Answers

1999-2003 Ford Windstar radio removal procedure


remove the trim around the radio face be careful not to break it, it should snap off its a delicate proceedure take radio face plate off ( if equipped) radio should come out

Nov 09, 2008 | 2003 Ford Windstar

Not finding what you are looking for?
2004 Ford Freestar Logo

Related Topics:

40 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

76848 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

fordexpert

Level 3 Expert

5546 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...