Question about 1996 Jeep Cherokee Sport

1 Answer

No problem, however I would like to convert my instrument cluster with digital gauges and adding a small fuel replacing the large fuel with a tachometer for a 1955 jeep cherokee 4.0 high output?

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 508 Answers

YOU ARE GETTING INTO AN AREA YOU DON'T EVEN WANT TO GET INTO. IT IS NOT WORTH ALL THE TROUBLE TO CONVERT. TRUST ME.

Posted on Jan 24, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

3 Answers

My speedometer works but my digital odometer does not work on my 2003 old alero


This is one guy's advice: Replace the speedo head, that should take care of the problem."

This site is also interesting because the guy said
General Motors cars had instrument cluster problems from 2003 through 2006. When I researched instrument cluster problems on the Internet what I found raised concerns in me. Many of those vehicles had problems that began with the instrument cluster, but eventually led to the engine refusing to start.
(an electronic instrument cluster, digital instrument panel or digital dash for short, is a set of instrumentation, including the speedometer, that is displayed with a digital readout rather than with the traditional analog gauges. Many refer to it simply as a digital speedometer.)

http://www.instructables.com/id/Erratic-Instrument-Panel-on-GM-Cars/

Feb 12, 2017 | 2003 Oldsmobile Alero

1 Answer

Where is the fuel gauge fuse on a 1998 Buick Century?


There is not a single fuse for the fuel gauge , there are a few that power up the whole instrument cluster ! If there were a fuse out more then just your fuel gauge wouldn't work .You probably have a bad sending unit in the fuel tank or the stepper motor for that gauge is bad ! The thing to do would be to take to the dealer or some other capable ASE certified repair shop that has a up scale scan tool that can check codes in the instrument cluster ! Or you can take a chance an replace the instrument cluster !
Fuel Gage Inaccurate or Inoperative
Inspect for any stored instrument cluster Diagnostic Trouble Codes (DTCs). Are any DTCs stored in memory?
--
Go to Diagnostic Trouble Code (DTC) List/Type
Go to Step 3

3

  1. Install a Scan Tool scan tool.
  2. Turn the ignition switch to the RUN position.
  3. Establish communication with the instrument cluster.
  4. Select special functions under the main menu.
  5. Select output control under special functions.
  6. Select fuel gauge sweep test under output control main menu.
Does the fuel gauge perform a full sweep when commanded?
--
Go to Powertrain On Board Diagnostic (OBD) System Check in Engine Controls - 3.1L
or
Powertrain On Board Diagnostic (OBD) System Check in Engine Controls - 3.8L
Go to Step 4

May 23, 2015 | 1998 Buick Century

1 Answer

None of my gauges are working ion my dash


Intermittent gauges usually mean a bad ground connection for the gauges. Things to check: look for multiple ground connections at one screw to chassis frame & tighten it; check large connector at rear of instrument cluster for good connection; replace gauges fuse - it can be cracked. If none of those work, than instrument cluster circuit board will probably have to be replaced - which means removing the cluster.

Jul 13, 2014 | 1997 Eagle Vision

1 Answer

98 Town Car, how do I change dash lights, (fuel gauge bulb)


  1. Disconnect the negative battery cable.
  2. Remove the instrument cluster.
  3. Remove the retaining screws for the instrument cluster lens and cover assembly. Remove the cover and lens.
  4. Remove the retaining screws for the gauge or warning lamp to be replaced and remove the gauge or warning lamp. To install:
  5. Place the gauge or warning lamp into place and tighten the retaining screws.
  6. Install the instrument cluster lens and cover assembly.
  7. Install the instrument cluster.
  8. Connect the negative battery cable.

Feb 04, 2011 | 1998 Lincoln Town Car

1 Answer

Trying to locate electrical junction to test fuel level sensor


Fuel Level Indication System The fuel level indication system is a magnetic gauge system. It consists of a magnetic fuel gauge (9280) mounted in the instrument cluster (10849) and a sending unit located in the fuel tank (9002) with an instrument cluster gauge amplifier (10E849) in series between the two. No instrument voltage regulator is used with this system. Fuel Gauge
The magnetic gauge movement consists of three primary coils, one of which is wound at a 90-degree angle to the other two. The coils form a magnetic field which varies in direction according to the variable resistance of the sender unit which is connected between two of them. A primary magnet, to which a shaft and pointer are attached, rotates to align to this primary field, resulting in pointer position. The bobbin/coil assembly is pressed into a metal housing which has two holes for dial mounting. There is no adjustment, calibration or maintenance required for these gauges. The instrument cluster amplifier is calibrated to the fuel gauge. The instrument cluster amplifier and fuel gauge must be replaced as a system. Instrument Cluster Gauge Amplifier/Check Gauge Module
The instrument cluster gauge amplifier electrically averages fuel sender readings so the fuel gauge displays actual fuel level and not fluctuations due to sloshing in fuel tank. The instrument cluster gauge amplifier is a small printed circuit board which latches into a pocket on the back of the instrument cluster. The electrical connections for ignition, ground, input from fuel sender and output to fuel gauge are made through a spring-type connector on the instrument cluster gauge amplifier to the instrument cluster printed circuit (10K843) on the instrument cluster. There are no provisions for calibration or adjustment of the instrument cluster gauge amplifier.
Fuel Sending Unit
The fuel sending unit consists of a variable screened resistor made up of a ceramic substrate. It is controlled by the action of an attached float in the fuel tank. When the fuel level is low, resistance in the sending unit is low. When the fuel level is high, the resistance in the sending unit is high. As the float moves from empty to full, the resistance will gradually and continuously increase. f9e3b50.gif

Mar 10, 2010 | 1997 Ford Ranger SuperCab

2 Answers

Speed ometer in the dash gives inaccurate reading while the digital reading in the widnshield appears to be correct. Fuel gauge has rapped around forward and temperature guage is off.


The problem here is your "Stepper Motors" are failing in the Instrument Cluster. If your Vehicle has "LOW MILEAGE" it may still be covered under factory warranty. Check with your Dealer first! If not covered under warranty, most reputable Speedometer Repair facilities can service it for you. All "Stepper Motors" in the Instrument Cluster should be replaced at the same time as the OEM versions are prone to ultimate failure.Typically, there are 5 or 6 dependent upon whether or not you have a Tachometer. They are: Speedometer, Temperature, Oil Pressure, Fuel Gauge, Volt Meter and Tachometer. The replacement part must have X25 168 where the X indicates an improved model.

Dec 12, 2009 | 2004 Buick LeSabre

2 Answers

Fuel gauge not working all the time.


This is a normal concern.
The instrument cluster uses 4 different operating modes to calculate the fuel level:
Anti-slosh (default mode)
Key OFF fueling
Key ON fueling
Recovery
After a fuel fill up, the time for the fuel gauge to move from empty (E) to full (F) ranges from 2 seconds to 55 minutes depending on which operating mode the fuel gauge is in.
The default fuel gauge mode is called the anti-slosh mode. To prevent fuel gauge changes from fuel slosh (gauge instability due to changes in fuel sender readings caused by fuel moving around in the tank), the fuel gauge takes approximately 55 minutes to go from empty (E) to full (F).
The key OFF fueling mode (2 seconds to read empty [E] to full [F]) requires 3 conditions be met:
The key must be in the OFF position throughout the entire refueling of the vehicle.
At least 15% of the vehicle's fuel capacity must be added to the fuel tank.
The instrument cluster must receive a valid key ON fuel sender reading within 1 second of the key being put into the RUN position. The key ON sample readings are considered valid if the fuel sender reading is between 15 ohms ± 2 ohms and 160 ohms ± 4 ohms.
If these conditions are not met, the fuel gauge stays in the anti-slosh mode, which results in a slow to read full (F) event.
The key ON fueling mode (approximately 90 seconds to read empty [E] to full [F]) requires 3 conditions be met:
The transmission is in PARK (P).
The key is in the RUN position.
At least 15% of the vehicle's fuel capacity must be added to the fuel tank.
In key ON fueling mode, a 30-second timer activates after the transmission is put into the PARK (P) position (automatic transmissions). When the 30-second time has elapsed and at least 15% of the vehicle's fuel capacity has been added, the fuel gauge response time is 90 seconds to read from empty (E) to full (F). When the transmission is shifted out of PARK (P), the fuel gauge strategy reverts to the anti-slosh mode. The key on refueling mode prevents slow to read full events from happening if the customer refuels the vehicle with the key in the RUN position.
Recovery mode is incorporated into the instrument cluster strategy to recover from a missing fuel level input during a refueling event. Missing fuel level inputs result from intermittent opens in the fuel sender or its circuits. Recovery mode (empty [E] to full [F] approximately 20 minutes) is initiated when the following 2 conditions are met:
The instrument cluster is in the anti-slosh (default) mode.
The actual fuel level in the tank is greater than what is being displayed by the fuel gauge

Feb 18, 2009 | 1983 Mercury Grand Marquis

2 Answers

Fuel gauge needle way past full, holding temp needle down so I cannot read temp either! 2005 with no low beams. Could problem be related?


Most likely this is the common 03-05 Cavalier instrument cluster problem where the stepper motors on the cluster's circuit board go out. It can be fixed, check this page for more on how to get it taken care of - Cavalier fuel gauge broken

Dec 30, 2008 | 2005 Chevrolet Cavalier

Not finding what you are looking for?
Cars & Trucks Logo

84 people viewed this question

Ask a Question

Usually answered in minutes!

Top Jeep Experts

yadayada
yadayada

Level 3 Expert

70374 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22041 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6878 Answers

Are you a Jeep Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...