Question about Cars & Trucks
a 6ya Mechanic can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repair professionals here in the US.
click here to Talk to a Mechanic (only for users in the US for now) and get all the help you need.
Posted on Jan 02, 2017
SOURCE: neutral safety switch....I think
The switch is located at the top of the clutch pedal assembly, above your feet. Its a little cramped, but its a simple dc two wire switch, you should be able to check it with a meter for power and to see if the switch does indeed need replacement. If thats the problem, when you see the new switch, you'll know it goes in, very easy. good luck
Posted on Aug 12, 2008
SOURCE: 2000 kia sephia clutch
this is a big job for someone who is not mechanically inclined but....here it goes go buy a new clutch new tranny fluid and a haynes manual at the auto parts store your going to have to drain and drop your tranny ... BUY THE CLUTCH WITH THE TOOL theres an alignment tool needed to align the plates n bearings start by pulling off both tires, brakes and both cv axels be sure to remove the intermediate shaft from the tranny on the passenger side (should come out with the axel passenger side only) so do yourself a favor and buy an impact gun with at least 500 ft lbs torque youll need it also have handy your 14mm 17mm and 19mm impact sockets and remember this job usually runs around 1,200 bucks at firestone also DO NOT remove the bolt in the middle of the front springs under the hood just the four around it and the will pop out no prob and wont need to be clamped remove the starter behind your engine its under the oil filter also if your new to this sorta thing its gonna take you about 3 days to do it buy the impact gun if ur in a hurry look at a pawn shop have your flywheel machined its going to be accessible and it needs it hope this helps dont forget the book which you should already have bought anyway its good for your torque specs which you will also need a torque wrench for the clutch also dont crack open ur tranny this isnt a honda
Posted on Jan 05, 2009
the fill plug will be on the side of transmision.where axle come out transmission. get a haynes manual because it can be helpful.
Posted on May 20, 2009
SOURCE: what wires do I need
The wires on the Transmission Range Sensor that control the ability to crank the starter are the BLACK/GREEN wire at Pin 6 and the wire at Pin 10 which is either BLACK/GREEN or BLACK WHITE depending on your model. (build - date and transmission type)
With all that said, I think it only fair to warn you that bypassing these wires will set codes in your Engine Control Module. It is not going to like it if there is power at pin 10 with the transmission in reverse or any of the forward gears. This may also cause your transmission to not shift properly because the ECM will not know for sure what gear you are in.
Posted on May 10, 2011
Testimonial: "thanks so much for the information I will install a switch and only use it when needed and to ensure that this is my problem."
Tips for a great answer:
Sep 26, 2016 | 1997 Kia Sephia
May 31, 2015 | 2003 Kia Spectra
Apr 22, 2015 | 2005 Pontiac Vibe
Sep 16, 2014 | 2000 Kia Sephia
Feb 09, 2014 | Kia Sephia Cars & Trucks
Jun 22, 2012 | 1992 Toyota Paseo
Jul 12, 2010 | 1999 Kia Sephia
Feb 21, 2010 | 2000 Kia Sephia
Jan 07, 2010 | 1999 Kia Sephia
May 25, 2009 | 1998 Chevrolet Metro
25 people viewed this question
Usually answered in minutes!
Step 2: Please assign your manual to a product: