Question about 2004 Rover 25 1.4

1 Answer

The boot light in my Rover 25 is receiving current and will work when I make an earth connection. It therefore seems that the "official" earth is not connecting. Where on the car's body does the e

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Rover Master
  • 645 Answers

The wiring around the tailgate hinge rh has look from rear can break inside the rubber sleeve check this first

Posted on Apr 11, 2013

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Which fuse forbreak light on Rover 25 2006 please. Both side break lights not working. Bar light is.


Check for bad connection at trailer hitch tap connector located on frame close to back bumper. Check owners manual for fuse location

May 19, 2017 | Rover Cars & Trucks

2 Answers

I have a 2004 rover 25 1.4, this morning tail lights and number plate light not working, reverse, fog and brake lights all fine, advise pleas?


Brake light? Some bad connections to light sockets if bulbs not burned out. Of course you will need help to see brake light when brake is pushed.

Mar 08, 2015 | 2004 Rover 25 1.4

1 Answer

Why won't my 2006;envoy battery stay charged. When I disconnect the positive battery cable it shuts off. I replaced battery and alternator numerous times. I even replaced the altenator plug but it still...


there is a power leakage in the electrical system
disconnect the earth cable from the battery and place an amp meter in the circuit ( terminal to lead end) and check for current reading. the amount of current flowing will give an indication of the drain and what is likely to be still on. ( glove box light,boot light,interior light,relays,fuel pump, faulty ECM radio amp or booster diode in alternator etc)

Feb 12, 2015 | Cars & Trucks

1 Answer

Passenger brake light not working rover 600 1996


Check feed and earth at light unit.
Earth terminal burns out

May 06, 2014 | 1998 Rover 600

1 Answer

Rover 25 indicator not working


Poor earth.
Try adding a better connection

May 04, 2014 | 2004 Rover 25 2.0

1 Answer

I just replaced the battery and alternator, but the battery light still stays on, what could it be?


When working correctly and charging, the alternator develops a voltage in the small wire at the back which, at the 'battery light' end, opposes the voltage supplied to the bulb from the battery. The bulb then goes out. This is not happening in your case, suggesting either a faulty alternator or a broken connection to the bulb. You need to use a multimeter with the negative probe earthed and the positive probe along the length of the small alternator wire to locate the break. If there is none, then I suspect you will find the alternator is not charging and therefore faulty.

Oct 02, 2013 | Land Rover Cars & Trucks

1 Answer

How to install maystar s20/50


Maystar s20-50 connections.
Red + to permanent supply via 15A fuse
Black - vehicle body earth wire
Pink - negative trigger input, connect to additional earthing (pin) switches for bonnet boot etc.
Violet - for connection to negative switched courtesy light door switchs
Blue - ACC wire connect to an ignition switch positive supply
Yellow- connect one yellow wire to the left indicator and the other to the right inicator. Ensure that you connect to the switch output to the bulbs, not the supply to the switch.
White - Current sense loop- cut for current sense leave intact for non current sense.
Green - Antenna wire must not be cut or terminated.
Quick connect, for connection to additional Maystar control modules and sensor systems, follow the instructions supplied with the additional sensor.

Jan 16, 2013 | Cars & Trucks

1 Answer

Where is the boot light earthed


riught up behind the panneling its easire to renew the earth and leave the existing earth wire connected as well so anything else using the same earth will work as well through the new earth.

Jan 14, 2013 | 2004 Rover 25 1.4

1 Answer

How do I fix the heater switch on a rover 25 1.4i Y reg


** First check the Fuse 19, 20A, in passenger fuse box (see manual- under steering wheel). then earthing connection E5 (Front LH inner wing.
**electricat connections are most accessable at Motor resistor bank, behind glove box (released by 8mm 2 bolts underneath ) Resistor pack in front of blower motor, 2x 6mm bolts. flick or squeese electrical relaese tab**



** Check the state of the motor speed resistor pack/ prone to resistor/resistor wire failure , which is behind the glove box,

The motor circuit is Green, live feed , to motor, slate black to motor speed selector (resistor pack), Output (slate or Yellow or Green or pink And Black) then Heater selector switch to earth (black).
- The feed from the motor is Slate/ Black wire. It pass through (or bypasses) resistor bank which limits the current through) the motor thus controlling. the speed. This has 4 connection slate grey from motor.

**Check 12v feed on blower Motor connector Green +ve , Slate Black to Earth. if ok, short Slate/black(Sl/Blk) to earth motor should run.

-Slate/B black (S/B) via No restor to switch, pos 4,

-Yellow/ Black (Y/B) via High resistor to Switch Pos 3
--Green/ Black (G/B) via Medium resistor to Switch Pos 2.
--Pink/ Black (K/B) via Xresistor to Switch Pos x.


From heater selector all final connection to earth are via to Black wire to earth on ineer LH inner wing.

Jan 17, 2012 | 2004 Rover 25 1.4

1 Answer

Brake light is on after changing pads and sencors


Check brake fluid level, if low top up & problem solved

If not, disconnect and reconnect the sensor wires ensuring a good connection. Check to see if solved.

If not, it seems that the sensors are perhaps receiving an earth signal somehow, check that the sensors are seated correctly.

Hopefully one of the above will sove the issue.

Regards

Lloyd

Dec 15, 2009 | 2005 Land Rover LR3

Not finding what you are looking for?
2004 Rover 25 1.4 Logo

Related Topics:

134 people viewed this question

Ask a Question

Usually answered in minutes!

Top Rover Experts

yadayada
yadayada

Level 3 Expert

74945 Answers

Thomas Perkins
Thomas Perkins

Level 3 Expert

14185 Answers

Rob
Rob

Level 2 Expert

62 Answers

Are you a Rover Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...