Question about 2002 Jeep Liberty

1 Answer

Changing brake pads and rotars

2002 jeep liberty - cannot get the rotar to budge - does the large nut in the center have to removed before taking it off? It appears the new one just goes over it?

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Scholar:

    An expert who has written 20 answers of more than 400 characters.

  • Expert
  • 141 Answers

Remove the cuter pin,than that big nut, but You will have to move the grease seal, that covers the inner bearing, under the big nut is the outer bearing, remember the one part of the bearing is attached to inside rotor in both bearings, also You gone have to pack bearing with new grease, don forget to remove caliper taht is bolted with two bolts on back of disk spender, good luck, also when you *** the nut again you gone have to *** it with not side free play and the washer on big nut has to move free, wile wheel spin perfect with out free play

Posted on Jan 24, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do I remove front rotors


Hi Richard remove the wheels brake calliper s and mounting brackets then if there is grub screws holding the rotars remove them then get a big hammer and remove thd rotars they get atuck with rust so don't be shy with the hammer. Regards Jim...

Jun 06, 2015 | 2006 Jeep Grand Cherokee

1 Answer

1999 plymouth breeze. step on brakes and the front brakes have a bad pulsing to them. previous owner hab brakes done rotars turned and pads replaced. any suggestions on how to address this problem


Symptom: Brake Pedal Pulsates Change When: Braking Change Where: Passenger Compartment Change -->lg-bl.jpg lg-br.jpg
Priority Action Part Type Cause 1 Inspect Brake Drum Specs Brake Drum Out of Adjustment, Out of Round, or Cracked. 2 Inspect Brake Drum Unevenly Worn or Out of Round Brake Drum(s). 3 Inspect Brake Rotor Incorrectly Machined Brake Rotor. 4 Inspect Wheel Bearing-Front Incorrectly Tightened or Installed Wheel Bearing. 5 Inspect Wheel Bearing-Rear Incorrectly Tightened or Installed Wheel Bearing. 6 Inspect Wheel Nut Loose, Worn, or Damaged Wheel Nut(s). 7 Inspect Rear Axle Bent Rear Axle.

Apr 13, 2013 | Plymouth Breeze Cars & Trucks

1 Answer

How do you take the disk rotars off


Remove the dust cap at the center, remove cotter pin and castle nut, remove brake caliper and mounting bracket for it and the rotor should come off with no problem.

Mar 08, 2011 | 2002 Ford Ranger Regular Cab

1 Answer

I have a 1999 lincoln continental and the front passenger side brake locks when driven for a while.


I just got a 1999 lincoln myself. And the front brakes locked up on it. Try to take off and it spit and sputter's. And floats around when try to stop. I replaced both brake calipers, pads, and one of the rotars. It had grooves wore in it. And changed the rubber hose going to the caliper. That is what the problem actually was. I noticed that the other side had already been changed beforre. But I wasn't sure. The caliper was rusted up where it got hot from rubbing. And it is posible for them to stick. Autozone $38 ea for calipers rebuilt. 40 for the pads. 20 for the rotar. And 35 for the hose. Now it drives like a dream.

Aug 29, 2010 | 1999 Lincoln Continental

1 Answer

Front rotors whine


a whine or a squeel
if you put hard long life pads on the material used sometimes makes that noise the nonmetalic pads are the best way to go as they don't wear out the rotors as bad but you need to change the pads sooner . the harder the pads the longer the life but they are hard on the rotors as well ,let the pads seat for a while and see if the noise eases up

Jun 09, 2010 | 1998 Jeep Grand Cherokee

1 Answer

Removing front rotar


rotar doesn't contain the studs, the plate/hub behind the rotar does - you need a 32mm socket to undo the axle nut to then get at the hub (need a flat screw driver to lever the nut tang up first). If it's seized on put the rotar and wheel back on (leave the axle nut off) and gently rock it in a top-bottom motion (not radially or axially) to free it up. you can then gain access to the hub and studs. put the wheel nuts back on the studs 2 -3 turns so that you have a 'seat' and using a bolt with a smaller dia to punch them out

May 08, 2010 | 1991 Subaru Legacy

1 Answer

Replacing mirror 2002 jeep liberty


three 10mm nuts hold mirror on under bezel small set screw bottom of bezel along with a philleps screw can sometimes wiggle bezelupwards and you can remove without removeing door pad.if pad must be removed loosen screws by door handle arm rest look for plugs with small screwdriver remove plugs and screws tap pad upwards with hand reverse procdure to complete.

Nov 22, 2009 | 2002 Jeep Liberty

3 Answers

Driving with parking brake on


More likely than not you wore the parking brake pads down. The parking brake pads are seperate from the rear disc brakes. They are a drum style. The rear rotars are designed to work as both drum and disc.
I would say in 20 miles you did little no no damage to drivetrain.
Typically when you get a brake job they will adjust the parking brake shoes. It is extremly easy if you have already gone and removed the brake calipers. Essentially you pull off the rotor (you would need a tool for this called a puller. not expensive, maybe $10. Something somone doing your brakes would have. Once the rotars are off you just turn a star gear.
This might add $15-20 to a standard brake job. Maybe $50 if the shoes need to be replaced.

Apr 30, 2009 | 2001 Subaru Forester

2 Answers

Right rear brake seizing up and pads are wearing out prematurely


welcome to fixya

you might want to change out the caliber ....

sounds like you have a bad caliber and it is sticking open so the brakes are locking up

hope this helps you out have a good day :

Jul 27, 2008 | Chevrolet C1500 Cars & Trucks

1 Answer

2002 Honda Odyssey Problem


Sorry class07932,
Please explain in more detail what you mean?

Rgards Johngee10

Jul 18, 2008 | 2002 Honda Odyssey

Not finding what you are looking for?
2002 Jeep Liberty Logo

Related Topics:

108 people viewed this question

Ask a Question

Usually answered in minutes!

Top Jeep Experts

yadayada
yadayada

Level 3 Expert

63456 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21981 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6812 Answers

Are you a Jeep Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...