Question about 2001 Kia Spectra

Open Question

2001 kia spectra how to remove torque converter nuts fot trany removal

Need info how to remove torque converter nuts for trany removal

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
fastboyz
  • 674 Answers

SOURCE: locating and replacing the o2 sensor on a 2005 kia spectra

a wrench and just unplug the sensor wire and screw out and install new one. they make a special socket but i just use a wrench.

Posted on Sep 11, 2008

Ad
  • 1214 Answers

SOURCE: replacing the alternator belt on 2001 kia spectra

Then you don't take anything off. There will be a spring loaded idler that tensions the serpentine belt. Take a socket or long 12 point wrench and attach to the center bolt of the tensioner, then rotate the idler wheel away from the belt, take the belt off. Slowly release the spring tension of the idler.
The 2nd belt should be set up the same way.

Posted on Jan 23, 2009

joboo1
  • 257 Answers

SOURCE: removing fuel line from fuel filter

Hi, Fuel filters and some other hose connections on vehicles today use a clip mechanism that is easily released with a small plastic tool. These tools are available in most auto parts stores. They come in a set to accommodate different size hoses, and metal barbs. Simply put the longer end of the tool toward the fitting and press to release. Good Luck!

Posted on Feb 14, 2009

emmetmyers
  • 37 Answers

SOURCE: how do i remove the rear speakers in a 2004 kia spectra?

did you check in the truck ?

Posted on Jun 19, 2009

ministock48
  • 258 Answers

SOURCE: how to remove cv drive shaft on 03 kia spectra

jack up the vehicle on the frame or on the body lip not on the front suspension take the lower ball joint loose and remove the axle nut and push the axle out of the knuckle and tie the knuckle up out of the way then you can take a pry bar and pry the axle out of the transmission being careful not to damage the seal. then reinstall new axle in reverse order

Posted on Nov 08, 2009

Testimonial: "i have done all that but can't get it to break free of trans any ideas i have tried prying and yanking thanks for your help"

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I have a 2001 pontiac montana and am trying to figure out how to change the starter.


STARTER REPLACEMENT (ENGINE ELECTRICAL) Document ID# 688149 Starter Replacement

Removal Procedure

Important: This vehicle uses the PG260 F1 starter motor. The starter motor is serviced only as a complete unit.
  1. Disconnect the battery ground (negative) cable from the battery. Refer to Battery Negative Cable Disconnection and Connection.
  2. Raise and suitably support the vehicle. Refer to Lifting and Jacking the Vehicle in General Information.


  3. Remove the starter motor BAT terminal nut and electrical leads.
  4. Remove the starter motor S terminal nut and electrical lead.
  5. Remove the torque converter cover. Refer to Torque Converter Cover Replacement in Automatic Transaxle - 4T65-E.


  6. Remove the starter motor bolts.
  7. Remove the starter motor.

Installation Procedure



  1. Install the starter motor.
  2. Notice: Refer to Fastener Notice in Cautions and Notices.
  3. Install the starter motor bolts.Tighten:
    Tighten the starter motor bolts to 47 [n-m] (35 lb ft).
  4. Install the torque converter cover. Refer to Torque Converter Cover Replacement in Automatic Transaxle - 4T65-E.


  5. Install the starter motor S terminal electrical lead and nut. Tighten:
    Tighten the starter motor solenoid S terminal nut to 3 [n-m] (27 lb in).
  6. Install the starter motor BAT terminal electrical leads and nut. Tighten:
    Tighten the starter motor solenoid BAT terminal nut to 10 [n-m] (89 lb in).
  7. Lower the vehicle.
  8. Install the battery ground (negative) cable to the battery. Refer to Battery Negative Cable Disconnection and Connection.

Aug 05, 2016 | 2001 Pontiac Montana

1 Answer

How do i remove the nuts on a torque converter on a 2001 mazda 626 with a 2.0 ltr engine


Hi Bradley:
I`ve always just used a six point socket, flex bar, and handle extension combined with brute force.

Jul 12, 2016 | Mazda Cars & Trucks

1 Answer

How to remove the Torque converter from the motor crankshaft of Kia Carnival. The engine is already out c/w the transaxle gearbox, and has been separated. How to remove the torque converter?


look for 4 bolts coming in from the engine side of the flex plate back into the torque converter housing. Once these out out you may have to use a pry bar to get the torque converter out of the spigot in the end of the crankshaft

Jan 12, 2015 | Kia Cars & Trucks

1 Answer

Drain torque converter


Remove trany and torque converter, tip converter to drain or drain trany fluid, fill drive and drain trany fluid again, fill again, drive away

Sep 22, 2012 | 1999 Plymouth Grand Voyager

1 Answer

Need to change alternator belt 2003 kia spectra


1. Remove AC and P'S drive belt, if equipped.

2. Loosen generator mounting bolt and adjusting bolt.

3. Remove generator belt.

4. Install new generator belt and adjust to specification.

5. Tighten all bolts to specified torque.

Tightening torque mounting bolt: 27-38 Lb-ft (37- 52 N.m. 3.8 -5.3 kg-m)

Adjusting bolt: 14 - 18 Lb-ft (19 -26 N.m. 1.9 -2.6 kg-m)

Image

6. Install AC and P'S drive belt, if equipped. and adjust to specification.

leedavidian_154.jpg

Nov 28, 2011 | 2003 Kia Spectra

1 Answer

How do i change the starter on a 1997 buick park avenue?


Removal & Installation To Remove:
Starter 9306xg03.gif

  1. Before servicing the vehicle, refer to the service precautions in the beginning of this section
  2. Disconnect the battery negative cable
  3. Raise and support the vehicle
  4. Remove the transmission cooler line clip if necessary
  5. Remove the torque converter cover
  6. Disconnect the battery positive cable from the starter
  7. Disconnect the wire from the starter solenoid S terminal
  8. Remove the 2 starter motor mounting bolts and the starter motor
To Install:
  1. Install the starter motor
    • Torque the mounting bolts to 32 ft-lbs (43 Nm)
  2. Connect the battery positive cable to the starter
    • Torque nut to 12 ft-lbs (16 Nm) (1997-2000);
    • Torque nut to 89 in-lbs (10 Nm) (2001-2005)
  3. Connect the starter motor S terminal wire
    • Torque nut to 22 in-lbs (2.5 Nm)
  4. Install the torque converter cover
    • Torque the bolts to 115 in-lbs (13 Nm)
  5. Attach the transmission cooler line clip
  6. Lower the vehicle
  7. Reconnect the negative battery cable
prev.gif next.gif

Dec 09, 2010 | Buick Park Avenue Cars & Trucks

1 Answer

06 Kia rio axel nut torque


HI. Nut torque will be at 85 Foot pounds

Aug 21, 2010 | 2006 Kia Spectra

2 Answers

2004 kia spectra new trans & torque converter code po741 after install why


it could be wiring fault, check connections and for damaged or trappet wiring,or it can be torque convertor clutch solenoid

May 28, 2010 | 2004 Kia Spectra

1 Answer

So on my kia spectra 5 the throw put bearing locks


thats because that type of clutch is a pull type not a push type, to remove the trans first remove the slave cyl then the 14mm nut that holds the fork arm lever its on top of the arm, then remove the arm off of the shaft, now remove the trans, the hard part is reasembly.. because you have to install the release bearing on the trans and snap it into the preasure plate, thats a whole nother story.......

Oct 18, 2009 | 2006 Kia Spectra

2 Answers

Ok so im still trying to pull my trany out of my 06 kia spectra 5 and it still wont come apart. with 3 people and pry bars it will only get past the flywheel then spring back agaisnt the block. there are...


Jake, The metal arm that goes through the side of the trans that presses against the clutch when you push on the petal has to come off and out of the trans. It pivots on a ball type thing. Push it forward off its pivot point and remove the arm.

Oct 18, 2009 | 2006 Kia Spectra

Not finding what you are looking for?
2001 Kia Spectra Logo

Related Topics:

21 people viewed this question

Ask a Question

Usually answered in minutes!

Top Kia Experts

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

yadayada
yadayada

Level 3 Expert

76846 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6927 Answers

Are you a Kia Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...