Question about 2005 Chevrolet Uplander

Open Question

2005 chevy uplander ignition lock cylinder removal

Posted by Anonymous on

5 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

co7196
  • 3433 Answers

SOURCE: ignition lock cylinder removal

turn to accessory and use straight paper clip yo pud pi inside the hole in front of the key while turning key to on and pulling out using key for a handle.

Posted on Sep 24, 2009

Mike258
  • 1498 Answers

SOURCE: how do you change a lock n key ignition switch on 1998 chevy 6 cy

STOP. STOP. STOP.
I WILL POST WITHIN THE HOUR.
In the meantime, click here for a few things you need to know before even considering working with undeployed airbags.

Mike

Posted on Nov 04, 2009

RonPark
  • 855 Answers

SOURCE: key won't turn in ignition...should I replace the

Try rocking the steering wheel back and forth. Also even though the tumbler is the cause most of the time you should check the electrical part of the switch at times when it goes it won't allow the key to turn. Rocking the steering wheel is so that you can make sure that it is not turning due to the steering lock putting to much pressure on the tumbler.

Posted on Nov 21, 2009

  • 1168 Answers

SOURCE: how do i turn off the abs light on a 2005 chevy

Hello Abintz.
When your ABS light is on you have a problem in the system.
As long as the light is on your ABS system does not function at all.
If you have already checked the harness and connections the next thingt you can check yourself is resistance values at the wheel speed sensors.
One at each front wheel and one in the output shaft housing to the rear drive shaft.
They should read very close to 1000 ohms.
The front sensors are usually the area of most problems I see. They are replaceable.
Other than that you really would be hard pressed to find any other issues without getting it scanned by a repair shop.
If you have further questions please put them in "add comments and I will return to answer.
Best of the season to you.

KL

Posted on Dec 20, 2009

Testimonial: "this sounds like a great explanation! i will get the codes read, then check the resistances. thanks for your time!"

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

HOW TO REMOVE IGNITION LOCK CYLINDER ON A2001ESCORTZX2


To remove an ignition lock cylinder on Chevy Uplander, you will need to unscrew the 4 small screws underneath the steering wheel. You can then pull the console apart, and get to the small screws to the ignition lock cylinder. You can then remove the ignition lock cylinder from the car.
--------------------------------------------------------------------------------------

New Arrivals
Emergency power supply

Jan 15, 2013 | Ford Cars & Trucks

1 Answer

2007 Chevy Uplander code P1174


P1174 Chevy - Fuel Trim Cylinder Balance.
Possible causes- Failed HO2S
- Ignition problem
- Fuel injection problem
- Engine mechanical condition
Symptoms- Engine Light ON (or Service Engine Soon Warning Light)

Apr 06, 2012 | 2007 Chevrolet Uplander

1 Answer

2005 chevy malibu i replaced ignition now it starts for one second then turns off is can i directly permantly insert the chip from the key directly into sensor box which is cinnected to the ignition &...


A common problem is the ignition cylinder and/or the ignition switch. With the buzzing of the relay, i would say all this may be related to the ignition switch. A low voltage supply to any of the circuits that the switch feeds will give strange electrical conditions. If going to replace the ignition switch, then also do the cylinder at the same time. With all things described, sure sounds like the ignition switch. P.S. The locks may be related to the ignition switch problem or not at all. With that said, would suggest looking at the BCM(body control module)It control locks, and also has alot to do with the security system. See picture at bottom of this page of corroded BCM connectors. 4- Passlock Ignition lock
cylinder removed.
Install new cylinder.Try to start- it wont or dies.Leave key on for 10-12 minutes, or until light goes out.Then turn off key for 10 seconds.Turn key to 'on' position for 5 seconds, then turn to start

Oct 27, 2011 | 2005 Chevrolet Malibu Maxx

1 Answer

2005 chevy uplander how to program key FOB?


Get a trick-Charger and hook up to battery, turn new key in ignition switch to "on" but do not start engine, turn headlights on ( thats why you need the charger) and leave it like that for 100+ minutes.
That should do the trick and reprogram the new key, otherwise dealer only! about $130.00

Dec 13, 2010 | 2005 Chevrolet Uplander

2 Answers

Need to remove factory overhead rear DVD player in a 2005 chevy uplander


how do I remove my dvd player in my 2006 chevy uplander? I need to replace it and dont want to spend that kind of money to have it pulled out. I dont see any screws or bolts

Nov 20, 2010 | 2006 Chevrolet Uplander

1 Answer

Howto change a key cylinder for a chevy cobalt


There is a TSB on this issues if your having ignition lock issues.
Service Information
2009 Chevrolet Cobalt | Cobalt, G5 (VIN A) Service Manual | View All Bulletins | Document ID: 2325129

#09-02-35-005: Ignition Key Difficult to Remove, Ignition Key Binds or Sticks in Cylinder (Replace Ignition Cylinder) - (Aug 10, 2009)

Subject: Ignition Key Difficult to Remove, Ignition Key Binds or Sticks in Cylinder (Replace Ignition Cylinder)

Models: 2008-2009 Cadillac CTS (Built Prior to VIN Breakpoint 90163371)

2005-2009 Chevrolet Cobalt (Built Prior to April 14, 2009)

2006-2009 Chevrolet HHR (Built Prior to April 14, 2009)

2007-2009 Chevrolet Equinox (Built Prior to July 2008)

2005-2006 Pontiac Pursuit (Canada Only)

2006-2009 Pontiac Solstice (Built Prior to April 14, 2009)

2007-2009 Pontiac G5 (Built Prior to April 14, 2009), Torrent (Built Prior to July 2008)

Attention: This bulletin only applies to vehicle equipped with automatic transmission.

Aug 05, 2010 | 2005 Chevrolet Cobalt

1 Answer

2005 chevy uplander has no spark


sounds like a bad crank sensor or a bad ignition module. such as a coil pack.

Feb 06, 2010 | 2005 Chevrolet Uplander

3 Answers

2005 Chevy Impala ignition switch stuck in off position


Someone may have tried to steal the car and damaged the lock's internal pins. Replace the entire lock with new.

Sep 08, 2009 | 2005 Chevrolet Impala

Not finding what you are looking for?
2005 Chevrolet Uplander Logo

Related Topics:

513 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

75822 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8210 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...