Question about 2002 Dodge Stratus

1 Answer

Turn signals and hazard lights won't work

I took out the factory stereo system and cut the wires before makin sure the key wasn't all the way off. Causing a short in a few fuses. I changed the ones blown that I found, but cannot find how to fix the signals. If you can help it would be great!

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Genius:

    An expert who has answered 1,000 questions.

  • Master
  • 2,920 Answers

You should have pulled the pos battery cable off before you cut the wires and it could be that some of the wires you cut were for the turn signals.

Posted on Jan 24, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I have a 96 chevy blazer and my hazard switch broke and then my turn signals quit working also. so we replaced the turn signal indicator switch (not sure if thats what its called) and hazard switch and...


if you have trailer wiring check it it might be a problem,, or you may have crossed something you have replaced, go through the switch and hazard, use test light / ohm meter

Oct 03, 2013 | 1996 Chevrolet Blazer

1 Answer

1998 Toyota Avalon turn signals stopped working


Its either the flasher's, the turn signal lever switch or the hazard switch.
Try pulling one of the flashers out and see if the other system starts working.
Has anyone installed aftermarket electronics or tampered with the wiring in either system? Like an ALARM system? Stereo?

Jul 08, 2013 | Cars & Trucks

1 Answer

I have a 1998 Chevy Z71 and I broke my hazard light button. My hazard lights won't go off so I had to pull the fuse out but now I don't have brake lights or turn signal lights. What should I do?


Pull the wires off the back of your hazard button ,isolate them with tape or terminal block until you replace your broken hazard button. Replace the fuse you took out.

Nov 10, 2012 | Cars & Trucks

1 Answer

1992 Ford Ranger Turn signal/Hazard light issue


Can you just check to make sure the ignition key switch is not staying over to far and not backing off when you try to start it. I had a truck that did that and it messed up my turn signals until I brought the key switch back a little after starting it. Just a simple idea. Be kind with your rating for me. Raz

Apr 19, 2010 | 1992 Ford Ranger

1 Answer

Problem with my 97 Chevrolet S10 Blazer


I'd look into the multifunction switch. That controles both hazard and turn.

Dec 12, 2009 | 1997 Chevrolet Blazer

1 Answer

Got my stereo stolen out of my 2005 Grand Am, and now neither my turn signals or my hazard lights work. I looked for torn or pulled out wires, but the only four that were loose were all attached to a unit...


The only thing that should not be working would be the audible turn signal / hazard signal sound. When the turn signals are activated, the audio (radio) system generates a clicking sound that indicates the signals are working.
When the radio is missing, no sound is generated.
Are your turn signals working outside, but no sound or are the signals not working at all.
Let me know.
Regards,

Apr 19, 2009 | 2005 Pontiac Grand Am

1 Answer

Turn signals and hazards won't work


Was there any electrical issues other than this? Was there anything done to replace an electrical part or a stereo, gps, or other devices added to your car? Was a wire spliced or any wires cut that your aware of? Maybe the tail lights wiring have been altered to add as a source for connecting a trailer wiring harness? Try removing the **** shell around the ignition and carefully inspect the wiring in and around for loose, faulty or wires that may have been cut. Youll want to disconnect the battery first so you wont accidently create a short or spark that could create a bigger problem! Inspect your turn signal switch while you have the **** shell removed and make sure the parts are all intact and functioning, as well as the hazard switch. Could also be that theres simply a wire or wiring harness that had been disconnected while someone was working on another area related to the area where the problem is occuring. Hope this info is helpful or at least leads you in the direction of locating the problem.

Apr 17, 2009 | 1994 Honda Civic

1 Answer

Hazard lights and turn signal dont work


check your mechanics re-wire job lol

Apr 15, 2009 | Toyota Camry Cars & Trucks

Not finding what you are looking for?
2002 Dodge Stratus Logo

Related Topics:

81 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dodge Experts

yadayada
yadayada

Level 3 Expert

61037 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6812 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...