Question about Cars & Trucks
Advice required on how to replace belt
Posted by Anonymous on
A 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
The service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Posted on Jan 02, 2017
The supercharged 3800 engine uses two accessory drive belts. The outer belt drives the supercharger. The inner belt drives the generator, power steering pump, coolant pump and air conditioning compressor. All driven accessories are rigidly mounted to the engine. Drive belt tension is maintained by the spring loaded belt tensioner. Each belt has its own tensioner.
Remove: Place a jack with a block of wood on it under oil pan to support engine. Caution : Be sure the wood block extends past the width of the oil pan to avoid damage.
Torque axis engine mount bolt where it connects the mount to the engine mounting bracket.
Electrical connector from crank sensor.
Engine mounting bracket lower stud and lower engine to allow stud to clear frame rail.
Raise engine and reinstall bolt into torque axis mount. Lower engine to allow spacer to be removed.
Spacer. Remove bolt from torque axis bracket and lower engine.
Electrical connector to crank sensor.
Mounting bracket stud.
Raise engine and install torque axis mount bolt.
Tighten bolt to 87 Nm (52 lb. ft.)
Good luck and hope this helps.
Posted on May 05, 2009
On my 2005 Tacoma with the 4.0L V6, I found it easier to change the belt from under the truck. Just remove the skid pan. Plenty of room to install the belt. The tensioner pulley is the one at about 2-o'clock from the crankshaft with the belt nearly all the way around it.
Posted on May 19, 2009
SOURCE: Serpentine Belt Replacement
serpentine belts should be replaced when cracks are running across"v" portions of belt,when missing ribs 1/2 " or longer,or cracks running parallel to "v" portion of belt. the thermostat should be replaced if the car seems to take a long time to warm up or if the engine runs hot
Posted on May 20, 2009
get a floor jack and a small block of wood. place the floor jack under the oil pan. jack up the jack until you feel it on the oil pan. remove the engine mount. you will need a deep 15mm socket and a 6inch extension. the mount has 4 bolts. remove it. then jack the engine up with the floor jack until the power steering reservoir almost touches the cowl. now take a long 14mm wrench and place that on the bolt head on the belt tensioner. pull the wrench until the belt slacks up. remove the belt. Installation opposite of removal. Here is a belt diagram. I hope this helps!! If you have any problems or questions e-mail me at: Redlinetech07@yahoo.com
Posted on May 23, 2009
SOURCE: Replacing serpentine belt
try these websites to see if they have your car listed it www.autozone.com and www.alldatadiy.com also try these website to see if you can get a diagram its www.webcrawler.com and for the most part they should be a diagram under you hood showing you how to install your new belt.
Posted on Jun 07, 2009
Tips for a great answer:
Apr 12, 2018 | Volkswagen Jetta Cars & Trucks
Dec 19, 2015 | Cars & Trucks
Jul 18, 2015 | 2004 Volkswagen Golf
Apr 22, 2012 | Cars & Trucks
Nov 26, 2010 | 1993 Volkswagen Eurovan
Sep 15, 2010 | 2003 Volkswagen Passat
Apr 15, 2010 | 1997 Volkswagen Eurovan
Sep 12, 2009 | 2000 Nissan Maxima
May 05, 2009 | 2006 Cadillac DTS
66 people viewed this question
Usually answered in minutes!