Question about Honda Pilot

Open Question

Turn key ignnigion dash lights come on but car won't start Honda Pilot 2010

I accidentally left the key in the ignition for about 20 minutes. When I came back to the car the linterior and exterior lights came on but the car won't start. I tried turning the key to the "lock" position and pulling it out and then trying to start the car again but it wouldn't work. I also was able to go home get another key and that would not start the car either.

Posted by on

Ad

4 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 2 Answers

SOURCE: 2004 Saab 9-3 key STUCK in central console ignition - car

try disconnecting the battery briefly and then reconnecting it. I had this happen to me on my 04 9-3

Posted on Jan 08, 2010

Ad
  • 57 Answers

SOURCE: Unable to turn key in ignition to start 2003 Honda Pilot .

Your ignition lock cylinder probably fell apart. They get worn out and the tumblers inside fall out and leave the cylinder inoperable. Get your lock cylinder replaced and you'll be good as new.

Posted on May 07, 2010

  • 630 Answers

SOURCE: 2003 Saturn Ion -just replace

Greetings,
Does the key have a chip in it? If it does, read the resistance accross both sides of the key chip on the 20k scale, buy a 96 cent pack of resistors from Radio Shack, and solder together a set of them that equals near 2% variance of what the key reads,shrink wrap them, try to locate the wiring and solder this resistance set up in the wires, try to start.
Wiring diagram is needed to be sure of the colors and location of wires to be spliced.

I came accross a remedy of some who had a remote control start installed and they stated this eliminated their starting horrors.
When you turn the key to start does it crank or does it make any sort of a noise, like a clicking to the relay?
try tapping the solenoid with a long bar tried just about everything else.

Posted on Jun 11, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Key wont turn in ignition


03 steering wheel locked up and key won't turn - Honda Element ...

www.elementownersclub.com > ... > Maintenance and Service

Jun 8, 2010 - 11 posts - ‎6 authors
since Friday, I have not been able to turn my ignition key or unlock the steering wheel. i have already- used graphite lubes and sprays Dash lights won't turn off after exit and door lock - Honda ...
Aug 17, 2010
key won't turn, problem & fix
Sep 8, 2007
More results from www.elementownersclub.com

Honda Ignition Lock Repair - YouTube

? 10:49
https://www.youtube.com/watch?v=T01989YN2Ew
Jan 20, 2013 - Uploaded by Flip Keys
Learn to repair all types of Honda Steering Lock. Either wi... ... I am in NJ and dealing with a key that will sometimes not turn in the ignition cylinder on a 2005 Honda Element. .... (2006 honda accord ) .... It won't turn or come out. ... When you put the rightkey in the slot (and through the key reader part of the ...

Key Won't Turn in Lock - Drive Accord Honda Forums

www.driveaccord.net/forums/4.../219529-key-wont-turn-lock.html

Jan 14, 2016 | 2006 Honda Element

2 Answers

How do i reset my manint req's light after an oil change on a 2003 Honda pilot


Reset oil service light Honda Pilot. From years: 2003, 2004, 2005, 2006, 2007, 2008, 2009, 2010, 2011, 2012.
How do you reset oil service light Honda Pilot. From years: 2003, 2004, 2005.
  1. Turn off the engine. Press and hold the SELECT/RESET button in the instrument panel and turn the ignition switch to run (one position before starting).
  2. Hold the button for at least 10 seconds, until the indicator resets.
  3. Turn the ignition off and then start the engine to verify the indicator has been reset.
How to reset oil service light Honda Pilot. From years: 2006, 2007, 2008, 2009, 2010, 2011, 2012.
Resetting the Engine Oil Life Display if maintenance service is done by someone other than your dealer, reset the maintenance minder as
follows:
  1. Turn the ignition switch to the ON (II) position.
  2. Press the select/reset knob repeatedly until the engine oil life is displayed.
  3. Press the select/reset knob for about 10 seconds. The engine oil life and the maintenance item code(s) will blink.
  4. Press the select/reset knob for another 5 seconds. The maintenance item code(s) will disappear, and the engine oil life will reset to 100.
All information is taken from the Honda Pilot owners manual.

Mar 09, 2015 | 2003 Honda Pilot

1 Answer

My 2006 Honda pilot won't start... For some reason I opened it using the key instead of the remote and when I turned the key to start everything went out all of a sudden and nothing turns on. Did I de


the manual covers this, the IMMO is active. ?
car will not crank, is that it? it must crank to start. so cranking is 1st.
you turn the key and the IMMO LAMP must NOT be showing its blocking starts. is it
do you have full batteryvoltage. 12.6v at the battery terminals
I waited a few minutes and the dash board lights started coming
that means the battery is dead.
the dash waring lights must come on ,at key on, fast
if not we fix that first. that means power lost, 12vdc power loss.
use a voltmeter. at battery

Jan 26, 2014 | 2006 Honda Pilot

1 Answer

2010 honda pilot tail lights and license plate light not working


park (tail, running) lights
there are 20 lamps in side and outside, are all 20 dead>
those lamps that glow HL switch 1st click is PARK
side lamps. dash lamps glow in park are they?
this answer , solves the who is bad.

as always, check all fuses first in both boxes
there may be a park relay./
alldata.com has the full schematic, if really curious. ...

Jan 10, 2014 | 2004 Honda Civic

1 Answer

I have an 2002 Chevy Impala, when I go to crank my car it won't do anything. I have to play with the ignition by turning the key back and forth in order for it to crank. what is that?


Why do so many people ask about an Alternator ?

It has nothing to do with the starting system

You said you have to play with the key & ignition switch
that may be a place to start

Dec 14, 2012 | 2002 Chevrolet Impala

1 Answer

My 2004 Honda Pilot ran fine then a hour later won't start. At first thought battery so we charged up usig one of those chargers you plug in. Lights flicker, and clicking sounds but won't turn


Check batry terminals are secure & free from corosion, check security of earth strap to engine & main power wire on starter, if ok have the batry load tested to ensure it can perform under load as the starter needs a lot of current. Have you tried a jump start?

Sep 24, 2012 | 2004 Honda Pilot

1 Answer

Honda odyssey parking lights won't go off


Most likely ignition wire in steering coloumn needs replaced.

Sep 20, 2012 | 2003 Honda Odyssey

1 Answer

Resetting a Key fob on 2007 Honda Pilot


to program a key fob- get in vehicle and close all doors. insert key into ignition, have all the key fobs you want to program for this vehicle in hand, programing erases all old fobs. turn the ignition switch to on(all dash lights light up, on click before starting the car). then hit the lock button on one of the fobs. turn the ignition to lock. turn the ignition back to run and press the lock button again from the same remote. repeat untill all the locks cycle. ones the locks cycle keep the ignition in run and press the lock button on each key fob(the ocks will cycle each time a button is pressed). then turn the ignition to lock after all fobs have been programed

Dec 31, 2009 | 2009 Honda Pilot

1 Answer

Redo code for 2007 Pilot key


ok get in the car, close the door, make sure all doors are closed.... put the key in the ignition, turn the key to on but without starting the car (lights on dash light up only) press and release the key lock button, turn key to off, without removeing the key.. turn to on without starting the car (dash lights up only) press and release the key lock button again, turn the ignition off, without removeing the key then turn back on (lights on dash on only without starting the car, press and release the key lock button , turn off the ignition without removeing the key, ..turn on the ignition once more without starting the car , press and release the key lock button and u should hear the door lock cycle ....leave the key in the ignition ... now press the lock button or unlock button on the other remotes one at a time if u have them.....u should hear the lock cycle indicateing all remotes are programmed.... kind of tricky to explain but you will get it, the sequence of turnin the key in the ignition on and off is only done with that one first key,,, remember after the door lock cyles press the lock or unlock button on the other remote fobs if if any...and ur done..may take u a few trys.. let me know how it worked out.

Apr 06, 2009 | 2007 Honda Pilot

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

34 people viewed this question

Ask a Question

Usually answered in minutes!

Top Honda Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Kevin Daniels

Level 3 Expert

1455 Answers

Are you a Honda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...