Question about Nissan Maxima

1 Answer

Where is the map/baro pressure switch solenoid valve located on 1996 nissan maxima

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Nissan Master
  • 14,251 Answers

Here's what it look's like.

Posted on Jan 16, 2013

2 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 1 Answer

SOURCE: Where is located MAP/BARO Switch Solenoid Valve in a nissan frontier 2001 3.3L V6

where is the map baro switch sol valve located

Posted on Nov 28, 2012

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Code reading is 1447 is it the same as 1440?


No these are 2 different fault codes, although they are related to the same system
EVAP control system does not operate properly.
- EVAP control system has a leak in the line between intake manifold and EVAP control system pressure sensor.

Possible causes include ...
- EVAP canister purge volume control solenoid valve stuck closed.
- EVAP control system pressure sensor and its circuit.
- Loose, disconnected, or improper connection of rubber tube.
- Blocked rubber tube.
- Blocked or bent rubber tube to MAP/BARO switch solenoid valve.
- Cracked EVAP canister.
- EVAP canister purge volume control solenoid valve.
- Closed Throttle Position Switch.
- Improper connection of one-way valve.
- Blocked purge port.
- EVAP canister vent control valve.

Nov 02, 2016 | Cars & Trucks

1 Answer

What does code p1447 mean ...???


The code says "evap purge flow monitor fault"
Possible causes include ...
- EVAP canister purge volume control solenoid valve stuck closed.
- EVAP control system pressure sensor and its circuit.
- Loose, disconnected, or improper connection of rubber tube.
- Blocked rubber tube.
- Blocked or bent rubber tube to MAP/BARO switch solenoid valve.
- Cracked EVAP canister.
- EVAP canister purge volume control solenoid valve.
- Closed Throttle Position Switch.
- Improper connection of one-way valve.
- Blocked purge port.
- EVAP canister vent control valve.


This is a "jackpot" code. It points to so many possible causes as to be almost useless.

Feb 15, 2013 | 1996 Nissan Maxima

1 Answer

I have a 1998 Nissan Maxima GLE, I Failed the Emission Inspection (DTC) Diagnostic Trouble Codes of "P1492","P1105" What these Codes exactly? mean


A code P0300 may mean that one or more of the following has happened:
  • Faulty spark plugs or wires
  • Faulty coil (pack)
  • Faulty oxygen sensor(s)
  • Faulty fuel injector(s)
  • Burned exhaust valve
  • Faulty catalytic converter(s)
  • Stuck/blocked EGR valve / passages
  • Faulty camshaft position sensor
  • Defective compute
  • P1105MAP/BARO Pressure Switch Solenoid Valve
  • Check and clean the MAP sensor, or replace.
  • P1492EVAP Canister Purge Control/Solenoid Valve (Circuit)
  • Replacing the purge solenoid will clear code P1492 This should also clear code P0300 as well.

Oct 16, 2012 | 1998 Nissan Maxima

2 Answers

Where is located MAP/BARO Switch Solenoid Valve in a nissan frontier 2001 3.3L V6


Looking at the vehicle its on the right hand side,also before condeming,make sure the MAF (mass air flow ) boot is not torn and there is no vacuum leak causing false air8_5_2012_5_02_03_pm.gif8_5_2012_5_02_33_pm.gif

Aug 05, 2012 | 2001 Nissan Frontier Crew Cab

1 Answer

I took my car to get an emission and the P1105 code occured. MYcar is a 1997 nissan maxima.


P1105 = MAP/BARO Pressure Switch Solenoid Valve

The problem is in the map sensor circuit, it could be solenoid valve. Check the vacum line that goes to the MAP sensor.

From the B14 Factory Service Manual, has a procedure for checking the MAP/BARO solenoid valve when P1105 is tripped. It is rather complex, and you will need a volt meter, but...

1- Warm up the car and pull the vacuum hose connected to the MAP/BARO switch solenoid with the engine idling. There should be vacuum there (~ -20in Hg). If NG, replace the hose.
2- Check the vacuum hose between the Absolute Pressure Sensor and the solenoid for splits/cracks and clogging (blow through it).
3- With the engine off, disconnect the solenoid electrical connector. Turn the ignition switch on. Check the voltage between terminal 2 (brown wire) and ground. It should be 12v (battery voltage). If no voltage, check the 10a fuse #21.
4- Check Absolute Pressure Sensor. Remove the sensor with its wiring connected. (Located near the top of the firewall next to the cruise control actuator [disk-shaped on a bracket]). Remove the hose and turn the ignition on. Voltage between terminal #2 (white wire) and ground should be 3.2-4.8v. Apply a vacuum to the hose and the voltage should be 1-1.4v lower than the first reading. If NG, the sensor is bad.
5- Check the solenoid. Remove the solenoid electrical connector and hoses and check the air passage continuity by applying 12v to the connections. With 12v on, there should be continuity between the two close hose connections, and no connection between the lone connector and the double connection closest to it. With no voltage applied it should be the opposite (no continuity between the close ones, and continuity between the far one and the closest double one). If NG the solenoid is bad.

I hope this help.

Aug 18, 2010 | 1997 Nissan Maxima

2 Answers

P1105


MAP/BARO Pressure Switch Solenoid Valve

1- Warm up the car and pull the vacuum hose connected to the MAP/BARO switch solenoid with the engine idling. There should be vacuum there (~ -20in Hg). If NG, replace the hose.
2- Check the vacuum hose between the Absolute Pressure Sensor and the solenoid for splits/cracks and clogging (blow through it).
3- With the engine off, disconnect the solenoid electrical connector. Turn the ignition switch on. Check the voltage between terminal 2 (brown wire) and ground. It should be 12v (battery voltage). If no voltage, check the 10a fuse #21.
4- Check Absolute Pressure Sensor. Remove the sensor with its wiring connected. (Located near the top of the firewall next to the cruise control actuator [disk-shaped on a bracket]). Remove the hose and turn the ignition on. Voltage between terminal #2 (white wire) and ground should be 3.2-4.8v. Apply a vacuum to the hose and the voltage should be 1-1.4v lower than the first reading. If NG, the sensor is bad.
5- Check the solenoid. Remove the solenoid electrical connector and hoses and check the air passage continuity by applying 12v to the connections. With 12v on, there should be continuity between the two close hose connections, and no connection between the lone connector and the double connection closest to it. With no voltage applied it should be the opposite (no continuity between the close ones, and continuity between the far one and the closest double one). If NG the solenoid is bad.

Oct 17, 2009 | 1997 Nissan Pickup

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

211 people viewed this question

Ask a Question

Usually answered in minutes!

Top Nissan Experts

yadayada
yadayada

Level 3 Expert

75117 Answers

Phil Lovisek
Phil Lovisek

Level 3 Expert

705 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Are you a Nissan Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...