Question about 2001 Isuzu Rodeo

1 Answer

Starter appears bad,how do you remove it ? - 2001 Isuzu Rodeo

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Isuzu Master
  • 5,371 Answers

First, take off the negative battery cable. Then on the starter will be two electrical connections- remove the nut for the big battery cable there, pull it off, and the small wire to the starter solenoid mounted on the starter motor. Now all that's left to do is to remove the two (sometimes 3) starter mounting bolts. When they are removed, starter can be taken out. If any brackets are in the way, remove them first-sometimes a holding bracket is also bolted there to stabilize the heavy starter. That's all, good luck.

Posted on Jan 16, 2013

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

2000 ford windstar 160k with starter removed flywheel turns hard using ratchet and hits a hard point during the rotation. Mechanic suggests it's a bad cylinder and that engine should be replaced....


When manually turning your engine over, even with the starter on / off, there will be some resistance. Before you condemn the engine, I would recommend you remove the oil pan and perform a visual inspection while someone else is turning the engine over. this may help you possibly find if there is something that is wrong.
If you are not mechanically inclined, I would recommend you take it to a known repair shop to perform the above mentioned inspection.

Jun 24, 2017 | 1999 Ford Windstar

1 Answer

Starter appears to be bad...battery cable post on the starter free spins. Starter does not engage. My problem is I can't see how to get the starter out. There isn't enough room to pull the starter out.


if it is a s-10 with a 4.3 you need to drop the exhaust at the manifold flange and at the cat converter then remove the support brackets it will then come down enough to disconnect the wiring
good luck
chris

Mar 11, 2011 | GMC Jimmy Cars & Trucks

2 Answers

1990 stanza car can be pushed and clutch start car.When you turn key on dash lights come on cae will not turn over. put in new battery did not help


Do you get a fairly loud 'click' when you turn the key to 'start'? If so, you need a meter or test light to check if power appears at the starter terminal when the solenoid clicks. If power appears, the starter requires repair or replacement (usually the brushes). If no power appears, then replace the starter solenoid. Hope this helps!

Nov 15, 2010 | 1990 Nissan Stanza

1 Answer

Where is the starter located on a 2001 toyota tundra


Starter Motor REMOVAL & INSTALLATION 3.4L Engine
  1. Before servicing the vehicle, refer to the precautions in the beginning of this section.
  2. Remove or disconnect the following:
    • Negative battery cable
    • Starter electrical connectors
    • Starter
    To install:
  3. Install or connect the following:
    • Starter. Tighten the fasteners to 29 ft. lbs. (39 Nm).
    • Electrical connections
    • Negative battery cable Fig. 1: Exploded view of a common starter - 3.4L engine 86822088.gif
4.7L Engine
  1. Before servicing the vehicle, refer to the precautions in the beginning of this section.
  2. Drain the cooling system.
  3. Relieve the fuel system pressure.
  4. Remove or disconnect the following:
    • Negative battery cable
    • Engine appearance cover
    • Air intake tube
    • Intake manifold
    • Starter motor mounting bolts
    • Starter wiring connectors
    • Starter motor
    To install:
  5. Install or connect the following:
    • Starter motor
    • Starter wiring connectors. Tighten the cable nut to 86 inch lbs. (10 Nm).
    • Starter motor mounting bolts. Tighten the bolts to 29 ft. lbs. (39 Nm).
    • Intake manifold
    • Air intake tube
    • Engine appearance cover
    • Negative battery cable
  6. Fill the cooling system.
  7. Start the engine and check for leaks.
prev.gif next.gif

Sep 18, 2010 | 2001 Toyota Tundra

1 Answer

I have established that my starter is bad, and I'm in the process of trying to remove it. I have removed the electrical wires, and the two retaining bolts (with extreme difficulty!) but there seems to be a...


It is a 3 bolt starter for sure, And yes the bracket has to be removed, Id advise removing the oil filter as well, But it can be done without it..

Jun 13, 2010 | 1993 Ford Tempo

2 Answers

Battery seems dead and car won't start but dash lights are on


battery has not totally dried off, charge could have been less, keep the nodes of the battery clean off the salty appearence...

Jun 09, 2010 | 2007 Audi Q7 4.2 FSI

1 Answer

Can't tell which starter to get for replacement. 1986 1.3L carb, 2 or 3 options for rebuilt replacement.


The absolute best and in my opinion the only proper way to make sure that you aren't stuck in the middle of a job you thought you could finish, is to remove the old starter & take it to have it matched exactly. They must have the same number & size of teeth, exact mounting flange & should appear to be duplicates down to the electrical connections..

Amazingly, the difference between a 6 tooth and 7 tooth starter can completely ruin either the starter, flywheel/starter ring, & in bad cases, the bell housing. Save trouble & match them side by side to be safe. Good Luck.

Jan 29, 2010 | 1986 Honda Civic

2 Answers

Car will not turn over


The most common problem would be a bad starter. The clicking sound is not always heard in a bad starter. The mentioning of no attempt to turn over shows that the process stopped at start (bad starter) Check the positive cable on the starter for corrosion. Otherwise, you will have to replace the starter. The problem is intermittent,stay aware It might start 2 or 3 times then out of nowhere. it will start give you problems. Avoid the headache, replace the starter.

Nov 17, 2008 | 1998 Oldsmobile Intrigue

1 Answer

Sometimes dead ignition


Connections are the most common either on the battery or the starter solonoid. Next would be a starter, but you would usually get a click down on the flywheel where the starter engaged but could not turn over. Finally an ignition switch, unlikely but contacts there do sometimes go bad there as well.

Sep 30, 2008 | 2001 Chevrolet S-10

1 Answer

My car has been having problems starting for a while now. It would just make a clicking noise when you start it but if you let it sit for a minute or two it would eventually start. Then recently it...


The clicking noise that you are describing is the starter solenoid plunger contacting the power feed wire contact (inside the starter) from the battery to the starter. The starter did not crank the engine because the other contact from the solenoid plunger was not transmitting battery voltage to the windings of the starter motor. This is a common problem. Replacing the starter plunger & both contacts would haved solve the problem. Regarding the replacement starters, I have observed many times that "aftermarket/rebuilt" starters are, at times, just as bad as the one you are taking out of your car. Try this: Remove the starter. Remove the 3 bolts on the side of the starter that retains a metal cover. Remove the cobver. Remove the metal plunger. Inspect the contacts and the bottom of the plunger. If anything appears burnt or worn, replace the contacts & the plunger.

Aug 13, 2008 | 1998 Toyota Celica

Not finding what you are looking for?
2001 Isuzu Rodeo Logo

Related Topics:

189 people viewed this question

Ask a Question

Usually answered in minutes!

Top Isuzu Experts

yadayada
yadayada

Level 3 Expert

76848 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Thomas Perkins
Thomas Perkins

Level 3 Expert

14384 Answers

Are you an Isuzu Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...