Question about 2006 Nissan Quest 3.5

Open Question

Camshaft position sensor location nissan quest

Posted by Anonymous on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 19 Answers

SOURCE: 2000 Nissan Sentra Crankshaft Position and Replacement

Go to dealership they will give a diagram to locate every single one. I replace them on my daughter car. I believe there were three sensors. I exactly know what you are talking about. I had a hard time locating the back one right above the drive shaft on driver side.

Posted on Oct 03, 2009

dttech
  • 4803 Answers

SOURCE: where is the camshaft positioning sensor located

Your 2004 Nissan Quest is most likely to be equipped with a 3.5L V-6 engine. This engine has 2 Cam (PHASE) sensors. One is located in the back of each cylinder head. You must remove your intake air duct to see them.

Posted on Oct 17, 2009

  • 2 Answers

SOURCE: crankshaft and camshaft sensors location in nissan altima 2003

You are incorrect sir. There is a very good Youtube video showing you exactly where it is that is how I changed mine. The Crankshaft is located behind the engine block below and around from the cam sensor which is easly spotted looking at the engine. The crankshaft is in a difficult spot but once you figure out where it is it's easy...ish hope this helps

Posted on Dec 10, 2009

precisionaut
  • 10 Answers

SOURCE: crankshaft sensor location

The diagram shows it to be to the right of the oil fill cap down in the bellhousing when viewed from overhead,two wire connector.Looks like it might be right next to or under the motor grab hook..look for black/yellow and light green wire at connector..Good luck.

Posted on Jan 25, 2010

johnjohn2
  • 5763 Answers

SOURCE: 1997 nissan quest camshaft sensor where is it & how to replace it

The camshaft sensor is located inside the distributor and is part of it, in order to replace it you must replace the distributor,to replace remove the dist cap. mark the location of the rotor,by marking where its pointing to, then mark the dist housing, so now theres a mark on the rotor and housing to show where rotor points, next mark the location of dist going into housing, mark the shaft and the block,because it spins in block this way you can line back up.next remove hold down bolt and pull out,mark the new dist in exacat same spots as the old so you can install back the same,you may have to put it in and pull it out until your marks are lined up,this way the timing will be dead on, when done you can check timing. good luck

Posted on May 09, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Location of the Camshaft Position Sensor "A" Circuit on 2004 Quest SE.


Sensor A is the sensor for the engine cylinder bank that is closest to the radiator.. I have attached a link you need to look at that shows the diagrams of the sensors, the sensor A is the one next to the nipple that the upper radiator hose connects to and is labeled "Bank Two" in the diagram.

Mar 28, 2017 | 2004 Nissan Quest

1 Answer

Location of the camshaft position sensor for a 2004 nissan quest 3.5 lit


well it will be on the front or along the camshaft somewhere so just look for the wires on the head somewhere ,do not know offhand as only ever see the diesel ones here ,too much tax on fuel to allow the luxury of a petrol engine

Apr 13, 2012 | Nissan Quest Cars & Trucks

1 Answer

Camshaft censer are there two are macanic said they are not working


Yes, your 2004 Nissan Quest is equipped with 2 camshaft position sensors. If your computer is setting OBD fault codes for BOTH sensors, it is HIGHLY UNLIKELY that both of your cam sensors are bad. You most likely have a timing issue like a broken timing chain guide or camshaft phaser (IVT) that is not functioning properly.

Jan 19, 2012 | 2004 Nissan Quest

1 Answer

Where is the camshaft position is locatedon a 2000 quest


CAMSHAFT POSITION SENSOR IS INTEGRAL PART OF THE DISTRIBUTOR.

Sep 19, 2011 | 2000 Nissan Quest

2 Answers

Where is the camshaft positioning sensor located in the 2004 nissan quest


Your 2004 Nissan Quest is most likely to be equipped with a 3.5L V-6 engine. This engine has 2 Cam (PHASE) sensors. One is located in the back of each cylinder head. You must remove your intake air duct to see them.

Oct 17, 2009 | 2004 Nissan Quest

1 Answer

2005 NIssan quest camshaft sensor


for a Nissan Quest, it is in the distributor. Not serviceable, replace distributor. Famous for nearing failing and getting brown dust on optical sensor for camshaft sensor. buy on ebay for $200. Cleaning optical sensor is temp repair.

Call dealer & see if yours is there too.

Jun 21, 2009 | 1997 Nissan Quest

1 Answer

Location of camshaft sensor 1 for a 1997 Nissan Quest


Go to Auto Zone, get a Haynes manual on this vehicle. It will tell you where it's at and also help you with future problems.

Jan 07, 2009 | 1997 Nissan Quest

Not finding what you are looking for?
2006 Nissan Quest 3.5 Logo

Related Topics:

98 people viewed this question

Ask a Question

Usually answered in minutes!

Top Nissan Experts

yadayada
yadayada

Level 3 Expert

74945 Answers

Phil Lovisek
Phil Lovisek

Level 3 Expert

705 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Are you a Nissan Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...