Question about Dodge Ram 2500

Open Question

Labor time to bleed brake

Year 2006 8 cylinder

Posted by Anonymous on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

c17hydro
  • 2984 Answers

SOURCE: 1996 PLYMOUTH VOYAGER BLEED BRAKES

Try this unless you have done so....just about fool-proof!!!


eb5406b.jpg
THIS IS FOR A ONE PERSON JOB. IT IS A ONE PERSON BRAKE BLEED KIT.

Posted on Mar 15, 2009

  • 42 Answers

SOURCE: brake pedal goes to floor after bleeding the brakes many times

start off by pumping the peddle 25 times with engine off ... bleed the abs system (usually has bleeder valves near/on control unit). then bleed the rest as usual with engine off ... DO NOT turn the key on while bleeding abs brakes.

Posted on Mar 18, 2009

  • 232 Answers

SOURCE: Spongy brakes after bleeding them 2 times. Should I try to bleed the master cylinder or replace it?

Honestly your guess is as good as mine. But I don't think the master cylinder is NOT bad you still have air in the system. Get a big bottle of brake fluid bleed all four sides until you run out of fluid or your brakes work properly. You should divide the bottle's content in four, then use each quantity in each side. You'll be removing air and contaminated fluid from the system. Get a small hose that fits on the bleeders and an appropriate container. I have a good feeling if you do this your brakes will work just fine. I don't know how you are bleeding the brakes. I'll let you know the proper way just in case. This is a two man job, with the wheel off, have someone start the car. Have them pump the brakes a few times to get pressure. 1With the brake pedal UP open the bleeder, 2then have your assistant press the brake pedal all the way down and leave it completely pressed down. 3Close the bleeder valve, once close and only with the valve closed have'm release the brake. Repeat as necessary, bake depressed, open valve first then press brake. DO NOT depress until valve completly closed. Close valve THEN depress. Good Luck!

Posted on May 15, 2009

mecanica03
  • 881 Answers

SOURCE: bleed brakes on 2003 toyota corolla

i try to help you, firts refill brake fluid container,open purge valve in one wheel front only,wait few minutes when drops fluid, close this valve and open other wheel, same procedure, finally repeat this in each 4 wheels

Posted on Jul 14, 2009

  • 225 Answers

SOURCE: brake bleeding

if you didn't bleed the lines after putting the master in. then there is a good chance there is air in the lines now. may go through a quart of brake fluid before all the air is out. remember to start at r-rear/ l-rear/ r-front/ l-front last.will take some time. don't forget to adjust the rear brake while your there to help with the pedal

Posted on Aug 13, 2009

Testimonial: "thank you"

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Brakes problem


at this point I suspect that it is as it appears not to be bleed the second 1/2 of the cylinder
You can get a book and follow the bleeding procedure as some GM product master cylinders require a switch,pin to be removed and a plug put in so that the pistons can move to allow the bleeding process
you could take it to a brake shop and ask what has to be done to get the master cylinder to bleed properly
getting a workshop manual would be a good place to start as bleeding brakes is not always simple unless you know how it all works

Aug 26, 2016 | Cars & Trucks

1 Answer

How can i bleed the brakes on a 2006 hyundai tucson without the scan tool


bleeding the brakes can be done manually with the help of another person. have your helper pump the brakes and hold the pedal until you release the bleeder enough to get air or fluid flowing and then shut off. you can then tell the helper to pump again but only after you have closed the bleeder. do this two times on each wheel starting with the wheel in the rear furthest from the master cylinder. then the other rear wheel then the front wheel furthest from the master cylinder and finally the other front wheel. you should get a better pedal each step. don't let the master cylinder reservoir run dry during this procedure.

May 02, 2015 | 2006 Hyundai Tucson

1 Answer

Only air coming out when bleeding a 2006 chevrolet cobalt ls.


Need to know what was done to need to bleed the brakes. Easiest way to bleed a brake system is the gravity bleed. Crack open all 4 bleeder screws a little, open your cap on the master cylinder, and wait. Make sure to keep plenty fluid in the master cylinder while doing this. After about 30 min or so you should have pure brake fluid coming out of all 4 bleeder screws. If you have one that does not have fluid coming out, tighten the others and open the one up more until fluid comes out. After all four wheels have fluid it is still a good idea to have a buddy help you bleed them once the old fashion way by pumping up the brakes, hold the pedal and crack open each beeder one at a time.

Mar 17, 2014 | 2006 Chevrolet Cobalt

1 Answer

Brake pedal to floor


first did you perform a bench bleed on the master cylinder? if not bench bleed the master cylinder. had a neighbor with a similar problem with a ford truck. did some reaserch and found the ABS system needed to be bled. one way to bleed air out of it is to connect the diagnostic computer and perform an ABS bleed and then bleed the brakes like you normaly would. The other way was to take the vehicle somewhere you can slide around safely and slam on the brakes causing the ABS to activate. do this a few times and then perform the normal bleed method.

Jan 17, 2013 | 2006 Kia Sedona

1 Answer

2007 dodge sprinter van brake bleeding


SOME SPRINTERS HAD RECALLS ON MASTER CYLINDERS YEARS 2006-2009 CHECK DEALER FOR MAYBE RECALL,IAM NOT SURE WHY YOUR BLEEDING THE BRAKES IF YOU HAD OPENED A LINE OR CHANGED A CALIPER THERE MABE AIR IN THE LINES-I ALWAYS USE A PRESSURE BLEEDER OR YOU CAN GRAVITY BLEED SYSTEM BY OPENING EACH BLEEDER SCREW UNTILL GOOD FLOW THEN CLOSEING-IF BLEEDING FOR MUSHY PEDAL CHECK BRAKES AND THICKNESS OF ROTORS-ARE THEIR ANY CODES -IS THE ABS LIGHT ON-IF ALL CHECKS OUT GO TO MASTERCYLINDER

Dec 30, 2011 | 2007 Dodge Sprinter

1 Answer

I have replaced the master cylinder on my 2006 chrysler town and country about every week we keep losing brake pedal so we have bleed them and get pedal back. the only place i find air is the front driver...


Could be a couple of problems, bad master cylinder (not bench bled properly or bad seal out of the box, I have had a few like that), proportioning valve seal, brake line not tight/sealed properly sucking air into system,bad caliper. First of all, are you losing brake fluid along with your pedal? Need to know that first. If you are, try to find where you losing it from, you will find your problem. There can be absolutly NO leaks in a brake/hydraulic system. If not, check that all lines are tightly seated and nuts are quite tight using a line wrench to get proper torque. If so, you can replace the master cylinder again (take old one back to store for new one under warranty) and be sure to thoroughly bench bleed. When bench bleeding, take your time, do not push plunger in too quickly, use a SLOW steady push until ALL bubbles, no matter how small have been eliminated. Tapping on the bottom of the cylinder while bleeding will help remove trapped air. Even a very small amount of air will take forever to bleed out at the calipers. If cylinder/all calipers/lines appear to be right, I would suspect the proportioning valve is faulty. To find it, follow brake lines from master cylinder to where they go into the valve. Replace. Hope that helps.

May 30, 2011 | 2006 Chrysler Town & Country

1 Answer

Brakes r mushy,i changed the master cylinder better for a week then mushy again then good again for about a week,have been doing this for 6 weeks,fluid doesnt go down,cant find no leaks, but air comes out...


Did you bench bleed the master cylinder? You should try bleeding the lines going to the master cylinder too, just bleed them same way you would a caliper, only your loosening the lines a bit, not a bleed screw. Then of course, for good measure, bleed each wheel.

Let me know how it turns out.

Apr 01, 2010 | 2006 Hyundai Elantra

1 Answer

How do I bleed the brakes on a 2006 hyundai santa fe


Start at rear and pump up brake pedal till hard and hold, while someone at rear releases bleed nipple, Person in car does not release pedal off the floor till bleed nipple is retightened. Repeat several times at each wheel, ensuring brake fluid never gets low in master cylinder.

Dec 01, 2009 | 2006 Hyundai Santa Fe

1 Answer

4 WHEELS LOCK UP


ABS (HECU) MODULE. Does your ABS/ESC light come "ON"? You'll need to take it in
a Hyundai Service Center (dealership), pay the diagnostic fee. They will tell you EXACTLY what the problem is and what's needed to fix it (parts, labor, tax, time-frame, etc.). This way you will find out which parts, if any, you need to fix it - perhaps fix it yourself.

Jun 26, 2009 | 2006 Hyundai Sonata

2 Answers

Brake lines still have air after bleeding


Bleed them again -- one bleed is not always enough.

May 05, 2009 | 2006 Jeep Liberty

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

27 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dodge Experts

yadayada
yadayada

Level 3 Expert

75807 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22133 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8172 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...