Question about 2000 Mercedes-Benz SLK

Open Question

I can't program my ML 350, 2007, to open the garage door.

I don't have manual since I lost it. Can someone post how to program the garage door opener.

Posted by on

5 Suggested Answers

warlock61
  • 659 Answers

SOURCE: 2007 Lincoln Town Car Limited-can't program garage door entry key

ok

Learn Mode
ani_caut.gif WARNING: A garage door opening system that cannot stop or reverse itself after detecting an object in its path does not meet current federal safety standards. To decrease the risk of serious injury or death, do not use the universal transmitter with a door opening system that lacks stop and reverse features as required by federal standards. This includes any garage door opening system manufactured before April 1, 1982.
ani_caut.gif CAUTION: During this procedure, the system that you are programming will be made to operate. Make sure that people or objects are clear of the garage door or gate being programmed.

  1. Select a universal transmitter button to train.
  1. NOTE: If more than one button is pressed, priority will be given to the lowest numbered channel.
    Press and continuously hold the button for 20 seconds. CHANNEL X TRANSMIT will be displayed (X will be 1, 2 or 3) during this time.
  1. NOTE: If the channel being trained has not been previously trained, the channel will immediately enter training mode (no 20 second delay).
    After 20 seconds, the display will read CHANNEL X TRAINING to indicate training has started.
  1. Point the original garage door opener transmitter at the overhead console. Hold down the original transmitter's transmit button so the overhead console can learn the original transmitter's frequency and data stream.
  1. Training will be completed in 100 seconds or less. CHANNEL X TRAINED will be displayed when training is complete. DID NOT TRAIN will be displayed if the channel did not correctly train.
  1. NOTE: Additional training may be required for rolling code equipped devices. For additional information, refer to Rolling Code Programming in this section.
    Release the channel X button. Training is complete.
Rolling Code Programming
NOTE: To train a garage door opener (or other rolling code-equipped devices) with the rolling code feature, follow these instructions after completing the learn mode.
  1. Locate the learn or smart button on the garage door motor head unit. Exact location and color of the button may vary by product brand. If there is difficulty locating the learn or smart button, refer to the device's Owner's Literature.
  1. Press and release the learn or smart button on the garage door motor head unit.
  1. NOTE: Following the previous step, there are 30 seconds in which to proceed.
    Press and release the programmed universal transmitter button. Press and release the universal transmitter button a second time to complete the training process. (some garage door openers may require this procedure to be done a third time to complete the training.)
Transmit Mode
  1. Select the button for the desired channel (for example, for the garage door you wish to open).
  1. NOTE: If more than one button is pressed, priority will be given to the lowest numbered channel.
    Press the button. CHANNEL X TRANSMIT is displayed.
  1. The correct signal is transmitted to the device being controlled.
  1. Release the button.
Erase Mode
  1. Simultaneously press and hold buttons 1 and 3 for 20 seconds.
  1. CLEARING CHANNELS will be displayed while the channel codes are being erased.
  1. CHANNELS CLEARED will be displayed when the erase operation is complete.
  1. Release buttons 1 and 3.
Universal Transmitter Default Code Mode Loading
  1. Press and hold buttons 1 and 3 simultaneously. CLEARING CHANNELS is displayed.
  1. After 20 seconds, CHANNELS CLEARED is displayed. Continue to hold buttons.
  1. After 10 more seconds, CHANNELS DEFAULTED is displayed when the default codes have been successfully loaded

Posted on Dec 31, 2008

  • 1 Answer

SOURCE: universal garage opener

The solution is in the owners manual.If you want to program the "homelink transmitter" in your car,you will need a remote unit for your garage door opener to do this.It is fairly easy and straightforward.I programmed my 07 Pac and it works great.Good luck!

Posted on Mar 22, 2009

emissionwiz
  • 70347 Answers

SOURCE: can't program my garage door opener

go to the link below (GM web site for owners) and then select your year and model, U will need a Yahoo mail account to sign in.

Posted on May 21, 2009

  • 8 Answers

SOURCE: how do you program a garage door opener on 2001

remote controls trasmit frequencies. I believe you hold your home remote control device within 2" to 5" of the car's remote control buttons. You select one button in the car which you wish to use as the garage access remote, and press it simultaniously with the home remote control button long enough for the blinking light to go on and blinks for 5 seconds. Then you are programmed. Test it to make sure it worked. If failed, try again. If it doesn't work, any Mercedes Dealership should do it for you FREE. Some of them now push for some money, but you tell them that you called Mercedes and based on your zip code they said you should go to this dealership and it will be done for FREE! They will take care of it immediately.

Posted on Oct 17, 2009

swolfinor
  • 504 Answers

SOURCE: Can't program hyundai sonata to open garage door

GOTO HOMELINK.COM

THEY MAKE THE SYSTEM AND HAVE INSTRUCTIONS YOU CAN DOWNLOAD.



HOPE THIS HELPS

Posted on May 26, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Remote door opener


So, you get out your remote control to your garage door opener and, then get your owners manual to your new car. You need to follow the instructions from the manufacturer to be able to program the remote control to the car.

Ok, you have followed the instructions from the car manufacturer and you press the button for the garage door to go up.......and nothing happens. So, then you think you have missed a step on the programing. Well, what most instruction manuals leave out is the step from programing the car/truck/van to the garage door machine itself. On the back side of your garage door opener is a panel called the logic board. The logic board is the computer or brain of the machine. Most new garage door openers now are a mulit-code machine. By that, i mean it uses several signals each time you press the button on your remote control. This is for security, so your code can't be stolen by a code-grabber.

Now, comes the step of programing the vehicle to your garage door opener. Once you have followed the instructions of programing your vehicle, you now have to "teach" the car to the garage door opener. You will need some help doing this. You will have to get someone to press the button in your vehicle and hold it down, while someone else has to press the learn button on the back your your garage door opener mounted on the ceiling. The learn button on the back of your machine will be square if using a liftmaster machine. Craftsman, Liftmaster, Chamberlain are all the same. Their learn buttons are square, and usually are yellow, red/orange, or purple. If using a Genie, it has a button that says "learn button".

The person pushing the button on the machine will only have to push and release the learn button. DO NOT hold this button down. If you do, it erases all of the programing in the machine, and you have to re-program all the remote controls that you have. You will have to read my other hub to find out how to do that. You will probably say a few words you shouldn't either. :-) Programing the vehicle to the machine only takes a second, and when the machine accepts the code, the light bulb on the machine should flash for a brief moment, and you should hear audible click. Yep, it's that easy! I dont know why the auto makers leave that step out. Anyway, i hope this helps, and if you have any questions.. leave them in my comments and i will try to walk you through it. See the photo above and you will see the typical logic board...the square red/orange learn button is easy to see. Just remember to press and release

May 08, 2012 | 1995 Lincoln Town Car

3 Answers

PROGRAM PRIUS GARAGE DOOR HOW DO I PROGRAM THE BUTTONS ON THE PRIUS' REAR VIEW MIRROR TO OPEN THE GARAGE DOOR


There was a minor change for mine to work.. see below..

- you must park your Prius close to the gate opener, leaving it running (obviously not in the way of the gate closing)
- Hold the button the the mirror and then push your garage door remote button and hold until the light on the mirror starts to flasyh fast. THIS programs the button on the mirror, but not the garage opener - yet (this was key for me)
- locate the "learning button" on the opener itself
- press the "learning button" on your gate opener and then get back into the Prius within 30 seconds (more time than it sounds) and press the SAME Homelink button you just programmed above. I don't recall how long I held the pre-programmed button, but the light will flash as I recall.
- Then, when working the garage door, you may need to hold the mirror button for a good second for it to work - but I had tried for months to get mine to work, and finally after reading many posts, the above sequence worked on my 2008 Prius with my Lift Master, Security + rolling codes garage opener.

Just - program the button on the mirror with your remote FIRST.. the garage opener will not work.. then use the Learn button on the garage opener and the SAME BUTTON you just programmed.. and it worked great for me. Not programming the mirror button first will not work. Using only the Learn button will not work. You must program the mirror first with the remote, then use the learn button and the SAME button on the mirror. Hope this helps.

Scott 2008 Prius with Lift Master Security + opener.
-

Oct 30, 2009 | 2007 Toyota Prius

1 Answer

Manual is lost need assistance with programming garage door to open from car


the garage door is coded with tiny switches to code with the remote if you lost the code make sure the codes in the remote is in sequence to the garage door remove the cover and look at the code and as well on the garage door motor area is a box cover remove this and ensure they match correctly

Sep 06, 2009 | 2002 Mitsubishi Diamante

1 Answer

Need to program/link garage door opener with the one on the visor in the car


Depending on the name brand of the garage door opener, there is a button on it you press and you have about 30 seconds to set the button in the car to the signal. Read you car manual on how to set the visor opener, probably press and hold the button in after pressing the button on the garage door opener motor. Get someone to help you in the garage on a ladder. Mine is a Sears and this is how it works.

May 29, 2009 | 2006 Audi A4

1 Answer

Programing auto garage door opener


Sorry, the process is simple but too lengthy to post here.

Goto homelink.com

They make the system and have very complete instructions you can download.

PLEASE NOTE: MOST but not ALL Brands / models of opener will work with this system.

Apr 18, 2009 | 1999 Oldsmobile Bravada

1 Answer

Setting garage door opener


Most openers are programmed the same. You normally program the house garage opener to accept the new remote. Your garage opener will have a button to press to add in a new remote. Normally you press this and then press the remote in the car and hold until your lights on your opener flash or the garage door closes. (check your manual on your garage door opener)

Mar 27, 2009 | 2005 Chevrolet TrailBlazer

1 Answer

PROGRAMMING IN CAR GARAGE DOOR OPENER TO GARAGE DOOR


Usually you just hold down the button in the visor, and while you're holding it down, aim your garage door opener at it and hold that button down so the frequency is grabbed by the built-in opener. That's how it worked in a few other cars that I've seen - try it out and see if it works for yours.

Sep 09, 2008 | 2002 Honda Civic

1 Answer

Can't program the homelink system to my garage door opener on slk280 2007. i know the garage door works with learn button as i programmed on another mercedes ml.


Have you remembered to push the little button on the head of the garage door. most of the new ones use a rolling code and you have to push the button and make it flash, then you just hold your button on you home link, it blinks slow I think then blinks fast. and you are done.

Aug 02, 2008 | 2000 Mercedes-Benz SLK

Not finding what you are looking for?
2000 Mercedes-Benz SLK Logo

Related Topics:

315 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mercedes-Benz Experts

Colin Stickland
Colin Stickland

Level 3 Expert

22041 Answers

yadayada
yadayada

Level 3 Expert

70347 Answers

Michael Contreras
Michael Contreras

Level 2 Expert

166 Answers

Are you a Mercedes-Benz Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...