Question about Mazda 626

Open Question

2000 mazda 626 windshield washer fuse

The windshield washer quit working so I replaced the pump but it still doen't work. The fuse block diagram doesn't list the washer just wipers. The wipers work so I don't think that fuse is bad. Which circuit is the washer on. BTW the owners manual is long gone. Thanks

Posted by Anonymous on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

tripletauto
  • 1450 Answers

SOURCE: Windshield washer fluid pump not working

this would still be under warranty

Posted on Dec 10, 2008

  • 7 Answers

SOURCE: 2000 Jeep Cherokee Windshield Washer

You have a motor for the front and rear washer. Check the fuses. If the intermitted wipers does not work, there is a relay under the dash near the steering colum that needs to be replaced.

Posted on Jan 01, 2009

Fleetw00d
  • 31 Answers

SOURCE: windsheld wiper motor fuse? for 93 accord

10 amp fuse No. 5, middle of the 2nd row from the bottom in the under dash fuse box.

Posted on Jan 27, 2009

  • 840 Answers

SOURCE: Rear Windshield Wiper Problems

Check the wiper motor connection if its touching anything and loose it will automatically ground out and check at connection make sure you put some gel and then snap it in/ Please rate my response thank you very much

Posted on Jan 31, 2009

johnjohn2
  • 5763 Answers

SOURCE: 2000 Saturn Ion windshield wiper quit where is

i dont think the ion was made in 2000, they started making them in 2003, heres a diagram of a 2003 ion fuse box and the wiper fuse location.hope this helps,858c93e.gif

Posted on May 07, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Why does my room fuse keep blowing


Now you have a big Short, will be a good ide to Run the scanner/computer and fix it. Do not waste time+money. Remember the electronic vehicle is complicated now.
see the diagram attached.fb2b20d0-ca04-4fbe-a0f3-cba7c3144854.jpg

Jul 27, 2013 | 2000 Mazda 626

2 Answers

2000 Mazda 626 brake lights (all 3) not working.


I know the answer to this. I just fixed my in laws 1999 626 with your exact problem. Power comes through the brake switch, and into what they call a "joint box". Basically this joint box is the back side of your fuse box where all the connectors go. Most likely you have a bad box, or connection at the box. It is the only other thing between your brake switch and rear brake lights.

Jun 15, 2012 | 2000 Mazda 626

1 Answer

The door lock button on the interior doesnt work. The button will now lock all doors. Also the windshield squirter doesnt work even though the resivor is full. I think it is a fuse.


On your Windshield "Squirter" commonly called a washer), it COULD be a fuse, but probably not. It is probably a blockage at the Suirter bit. Get a piece of very fine wire, and put it into the holes, to clear them out.

Jun 14, 2011 | 2000 Mazda 626

1 Answer

How do you find and replace the windshield washer pump on the 2005 dodge magnum RT


The pump is located inside of the fluid holding tank itself. I would suggest checking the 30 amp (pink) fuse for the windshield washer pump before attempting to replace the pump. The fuse is located in engine compartment distribution block. Find the location of the 30 amp fuse by looking in your car's manual. If the fuse looks fine try swapping it out with an identical 30 amp fuse from the distribution block and trying the washers again. I believe there is one other 30 amp fuse (possibly for the headlights?) in that same location.

Replacement (if necessary) is no easy task as it would require removing quite a few parts of the front fascia of the vehicle including the front bumper and possibly passenger's side fender.

Dec 10, 2010 | 2005 Dodge Magnum

1 Answer

2000 Mazda 626...turn key on...no fuel seems to get to engine...fuel tank is full...could fuel filter restrict and cause problem ?


Check the fuse for the fuel pump. if its bad replace it if it blows again change the fuel pump its on its way out

Apr 26, 2010 | 2000 Mazda 626

1 Answer

How to Replace a Fuel pump on a 2000 Mazda 626


yes it isn't that much if you buy them.they slide inside the coupler and release the line.

Dec 26, 2009 | 2000 Mazda 626

1 Answer

I have a 2001 626 4-clinder with a windshield washer pump that won,t work. I don,t know where to find it.


the pump is located inside the washer fluid reservoir.it is easy to service with the plastic inner fender removed.

Jul 29, 2009 | 1999 Mazda 626

2 Answers

Hi in need of a wiring diagram fuse box Mazda bongo


look here: http://www.bongoforum.co.uk/forum/Blah.pl?

Apr 07, 2009 | 1997 Mazda MPV

2 Answers

2000 Mazda 626 brake lights


try brake light switch on top of brake peddle

Sep 13, 2008 | 2000 Mazda 626

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

59 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mazda Experts

yadayada
yadayada

Level 3 Expert

75117 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7772 Answers

Are you a Mazda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...