Question about 1995 Chrysler LeBaron

Open Question

How do I remove rear seat on a chrysler lebaron srs?

SRS Convertable

Posted by Anonymous on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 80 Answers

SOURCE: 1982 Chrysler LeBaron Convertable

What happened on mine was the motor failed.Check behind he rear sear at the motor to see if you have voltage. I was't willing to replace the motor for 300 bucks so i disconnected the rod ends that push and pull the top and made it a manual top.Works fast and not too hard.

Posted on Jan 26, 2009

emissionwiz
  • 75108 Answers

SOURCE: Need to change fuel pump on 1994 chrysler lebaron 3.0 v-6

yes u need to drop the tank out. there is no underseat access.

Posted on Apr 11, 2009

  • 454 Answers

SOURCE: REAR WINDOW DRIVERS SIDE WILL ROLL DOWN BUT NOT UP

The control switch is probably bad. You could try taking it apart and looking for a broken piece. You may be able to get it to work again. Otherwise, just replace the switch with one you get from a junk yard.

Posted on Oct 23, 2009

Testimonial: "great i hope thats all"

Mustgo
  • 2359 Answers

SOURCE: SRS light

Here's a quick check list for most common cost of SRS / Air bag problem.

Dirty contacts on driver and passenger seat belt buckles

Dirty contacts on seat belt connectors (under seats)

Dirty contacts on driver and passenger sides weight sensors (under seat)

Seat covers

Weight on passenger seat
(Example: grocery package trigger SRS / Air Bag light on the way home.)

I recommend you to pass an vacuum over the contacts and use CRC electronic parts cleaner to rule out connectivity problem.

I DO NOT recommend disconnecting the negative battery connector to clean the code(s).

Without the code(s) the dealer will takes "BILLABLE" time to reproduce the problem.

======

Please rate my answer if it is useful to you.

Cheers,

Mustgo

Posted on Dec 16, 2009

  • 381 Answers

SOURCE: how do you remove the rear seat in a chrysler 300M

Grab the bottom seat cushion at the front of one side and pull it straight up then do the same on the other side. (you will have to pull up very hard) The bottom of the seat clips in. once you have the bottom out take the 2 bolts out of the seat belt fasteners that holds the bottom of the top seat cushion. Then pull straight up on the seat cushion to slide it off two tabs that hold the top.

Posted on Mar 29, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Where are the air bag sensors on a 2000 Lincoln towncar


Sensor - Front Crash Removal
WARNING: Vehicle sensor orientation is critical for proper operation. If a vehicle equipped with an air bag supplemental restraint system (SRS) is involved in a collision, inspect the sensor mounting bracket and wiring pigtail for deformation. Replace and properly position the sensor or any other damaged supplemental restraint system (SRS) components whether or not the air bag is deployed.
WARNING: Always wear safety glasses when repairing an air bag supplemental restraint system (SRS) vehicle and when handling an air bag module. This will reduce the risk of injury in the event of an accidental deployment.
WARNING: To reduce the risk of personal injury, do not use any memory saver devices.
NOTE: The air bag warning lamp illuminates when the RCM fuse is removed and the ignition switch is ON. This is normal operation and does not indicate a supplemental restraint system (SRS) fault.
NOTE: The SRS must be fully operational and free of faults before releasing the vehicle to the customer.
NOTE: Repair is made by installing a new part only. If the new part does not correct the condition, install the original part and perform the diagnostic procedure again.
  1. Depower the system. For additional information, refer to Supplemental Restraint System (SRS) Depowering and Repowering in this section.
  1. Remove the radiator upper sight shield (8C291).
  1. Remove the air bag sensor.
    1. Disconnect the air bag sensor electrical connector.
    1. Remove the three screws.
    1. Remove the air bag sensor.
    2. SECTION 501-20B: Supplemental Restraint System 2000 Town Car Workshop Manual REMOVAL AND INSTALLATION Procedure revision date: 06/10/2004 Sensor - Side Crash Removal
      WARNING: Vehicle sensor orientation is critical for proper system operation. If a vehicle equipped with an air bag supplemental restraint system (SRS) is involved in a collision, inspect the sensor mounting bracket and wiring pigtail for deformation. Replace and properly position the sensor or any other damaged supplemental restraint system (SRS) components whether or not the air bag is deployed.
      WARNING: Always wear safety glasses when repairing an air bag supplemental restraint system (SRS) vehicle and when handling an air bag module. This will reduce the risk of injury in the event of an accidental deployment.
      WARNING: To reduce the risk of personal injury, do not use any memory saver devices.
      NOTE: The air bag warning lamp illuminates when the RCM fuse is removed and the ignition switch is ON. This is normal operation and does not indicate a supplemental restraint system (SRS) fault.
      NOTE: The SRS must be fully operational and free of faults before releasing the vehicle to the customer.
      NOTE: Repair is made by installing a new part only. If the new part does not correct the condition, install the original part and perform the diagnostic procedure again.
      NOTE: Left side is shown, right side is similar.
      NOTE: The side crash sensors are located under the carpet beneath the front seats.
      1. Position the seat to gain access to all fasteners.
      1. Depower the system. For additional information, refer to Supplemental Restraint System (SRS) Depowering and Repowering in this section.
      1. Remove the front seat. For additional information, refer to Section 501-10 .
      1. Remove the safety belt anchor bolt cover.
      1. Remove the bolt and the safety belt anchor.
      1. Remove the front and rear door scuff plates.
      1. Remove the lower B-pillar trim panel.
      1. Remove the carpet to access the side crash sensor.
      1. Remove the side crash sensor.
        1. Remove the retaining bolts and position the side crash sensor in order to disconnect the electrical connector.
        1. Disconnect the electrical connector.
        1. Remove the side crash sensor and bracket.

Dec 16, 2015 | 2000 Lincoln Town Car

1 Answer

How do i deactivate srs so i can replace front seatbelts on 2005 yaris


Disconnect the battery negative terminal.
1. Wait at least 90 seconds after the ignition switch is
turned off and the negative (-) terminal cable is
disconnected from the battery before starting the
operation.
(The SRS is equipped with a back-up power source, so
if work is started within 90 seconds of disconnecting
the negative (-) terminal cable of the battery, the SRS
may be deployed).
2. Do not directly expose the steering pad, front
passenger airbag assembly, center airbag sensor
assembly, front airbag sensor, front seat inner belt
assembly, seat position sensor, occupant
classification ECU, front seat side airbag assembly,
side airbag sensor, curtain shield airbag assembly,
rear airbag sensor or front seat outer belt assembly to
hot air or flames.

Feb 26, 2013 | 2005 Toyota Yaris 1.3

1 Answer

Reset srs light after replacing seatbelt


To reset the SRS light on an Acura Integra, pull down the SRS service connector. Unplug this connector so you have access to jump the harness. Start with the ignition OFF. Jump the SRS plug. Turn the ignition ON. The SRS light will come on then off.------------------------------------------------------------------------------
autel maxidas ds708

Jan 14, 2013 | 2007 Ford Explorer Sport Trac

1 Answer

REAR WINDOW DRIVERS SIDE WILL ROLL DOWN BUT NOT UP ? 1989 CHRYSLER LEBARON GT 2D CONVERTABLE


The control switch is probably bad. You could try taking it apart and looking for a broken piece. You may be able to get it to work again. Otherwise, just replace the switch with one you get from a junk yard.

Oct 23, 2009 | 1989 Chrysler LeBaron

3 Answers

What the srs light means


Your SRS light is related to your "airbag system". You need to have it repaired because you have no airbags while that light is on.

Jun 11, 2009 | 1992 Honda Accord

1 Answer

Front headrest, ford focus


Seat Backrest — Front adobe.gif Printable View (404 KB) Disassembly
All vehicles
ani_caut.gif WARNING: Always wear safety glasses when repairing an air bag supplemental restraint system (SRS) vehicle and when handling an air bag module. This will reduce the risk of injury in the event of an accidental deployment.
ani_caut.gif WARNING: Never probe the connectors on the air bag module. Doing so can result in air bag deployment, which can result in personal injury.
ani_caut.gif WARNING: Front seat back trim covers installed on seats equipped with side air bags cannot be repaired, they are to be replaced. Cleaning is permissible.
ani_caut.gif WARNING: To reduce the risk of personal injury, do not use any memory saver devices.
NOTE: If a seat equipped with a seat mounted side air bag and/or a safety belt pretensioner (if equipped) system is being serviced, the supplemental restraint system (SRS) must be depowered.
NOTE: The air bag warning lamp illuminates when the RCM fuse is removed and the ignition switch is ON. This is normal operation and does not indicate a supplemental restraint system (SRS) fault.
NOTE: The SRS must be fully operational and free of faults before releasing the vehicle to the customer.
  1. Depower the SRS. For additional information, refer to Supplemental Restraint System (SRS) Depowering and Repowering in the General Procedures portion of Section 501-20B.
  1. Remove the head restraint.
  1. Remove the head restraint guides.
    • Using a suitable screwdriver, depress the locking tang.
    e0008398.gif

May 31, 2009 | 2004 Ford Focus

2 Answers

SRS light


SRS if you didn't already know is your secondary restraint system (airbags)...... you can try resetting it by unhooking the battery for about ten minutes.... before you do that you may want to go down to autozone and have them scan the codes to see what it is showing.

May 23, 2009 | 2003 Chrysler Town & Country

1 Answer

CLK 320, the SRS light come on


Hi, There is a connector on the bottom side of the seat belt buckle. remove the rear seat bottom and check to see if the connector is damaged or just disconnected. The srs light has to be cleared using a scan tool.

Feb 27, 2009 | 2002 Mercedes-Benz C-Class

1 Answer

Srs warning light


Check under the drivers and passengers front seat for electrical cables. sometimes the connections can get disturbed by feet or items that have rolled under the seats (specially if you have kids)making a bad connection of the cables
As for the rear door window mechanism, you must remove the door trim pad and you will see the mechanism with its electrical motor etc, just undo the bolts and remove it.
Hope this helps

Feb 03, 2009 | 2002 Land Rover Freelander

Not finding what you are looking for?
1995 Chrysler LeBaron Logo

Related Topics:

26 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chrysler Experts

yadayada
yadayada

Level 3 Expert

75077 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7768 Answers

Are you a Chrysler Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...