Question about Honda CR-V

Open Question

How to replace rear wheel bearing 2005 camry - CR-V Honda Cars & Trucks

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad
  • 1 Answer

SOURCE: Rear Wheel Bearing Repair; 2005 pontiac aztek

Remove the brake caliper
Remove the disc, (rotor)
Remove the 34mm nut on the axel shaft
Remove the three (3) bolts from the back side
You will need a wheel puller (three jaw will work well)
Place the puller over the hub and tighten, this will push the shaft out of the hub. Now you have to pull the hub assy. out of the mounting bracket. I found hitting each side,of the hub with a lead hammer to work well. Don't forget to disconnect the ABS senser on the back side of the hub assy.
Do not over tighten the 34mm axel nut when you install the new assy. If you use an impact whrench on it you will damage the bearing.

Posted on May 03, 2009

Ad
  • 52 Answers

SOURCE: how to replace rear wheel bearing on s type jaguar v reg

pretty basic the same and any other wheel bearing. But you need a hydraulic press, if you dont have one of those then their is just no way that you will be able to do it.

If it is newer than an 05 you need to take it to the dealership, because they need to hook up their computer and electronically disengage the rear parking brakes by putting it into service mode.

Posted on May 11, 2009

Mr BrokRench
  • 1623 Answers

SOURCE: I need instructions on how to replace rear wheel bearings on my 1994 Honda Civic

Bearings are pressed into the hubs...much easier, faster and economical (if you don't have a press) to replace the complete bearing/hub assembly, no pressing is needed, since bearings are already pressed into the new hubs. Cost..aprox, 60 buxs each.
Here are the steps for the rear replacement...
Loosen the lug nuts on a rear wheel. 2) Chock the wheels and jack the rear of the car on the side with the lug nuts that you just loosened. 3) Remove the wheel by removing the lug nuts. 4) Pry open the dust cap covering the center of the axle/spindle. A small screwdriver tapped into the space between the hub and dust cap will work well for this. 5) With the dust cap now removed, use a thin center punch to straighten the little dent in the rim of the spindle nut so that you will be able to turn it freely in the next step. 6) Use a 32mm socket and a large breaker-bar to loosen the spindle nut. Unscrew the nut all the way and place it in a clean, safe area. 7) You should now be able to slide the hub/bearing assembly from the shaft. 8) Installation is the reverse of removal. Use plenty of high-temperature wheel bearing grease on all surfaces before you mount the replacement hub assembly.

IMPORTANT: Torque the spindle nut to 134 ft/lbs....(per manual specs)

When reinstalling the dust caps, tap them gently into place to avoid denting them...Install wheels, jack her down and pat yourself on the back...job complete.
Good luck..hope this will fixya up...please take time to leave me a fixya rateing...

Posted on May 23, 2009

  • 119 Answers

SOURCE: Procedure for replacing rear wheel bearings 2000 Forester

i'm assuming you don't have a hubshark,this is a tool that will alllow you to remove the bearing while the knuckle is attached to the car,you may be able to rent this tool at a auto prts store .if not you need to remove the entie knuckle,first remove the trailing arm bolt,then the lateral link bolt{long and stubborn bolt},disassemble the brake shoes and parking brake cable,abs sensor if equipped the knuckle to strut bolt{no marking necessary they are not eccentric} then you need a to use or borrow a press to remove hub and bearings good luck

Posted on Jul 26, 2009

  • 101 Answers

SOURCE: how do i replace the rear wheel bearing on my peugeot 206

wheel off remove the tin cap in the centure of the hub undo the big nut put the wheel back on with just 2 bolts finger tight so you can pull the hub off.once the hub is off take the 2 wheel bolts back out.now look in side the hub were the big nut was and you will see a sir clip take that out.then use a socket and a bench vice to press the old bearing out.use the socket and bench vice to put the new bearing back in.

Posted on Aug 01, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How many rear wheel bearings are there on chevy equinox 2005


There are two rear Wheel hub on a chevy equinox. You also have a rear differential containing bearings.

Sep 13, 2014 | 2005 Chevrolet Equinox

1 Answer

DO YOU HAVE DO REPACK WHEEL BEARING ON A 2005 ESCAPE AFTER 120,000 MILES


If you're talking about the front wheel bearings, they can't be serviced. They can only be replaced. They are sealed for life (even if the life seems to be a little short).
Here's the front bearing:

zeevert_43.jpg
I never replaced the rear bearings on my 2002 Escape 4X4, but here's a picture of the rear hub.

zeevert_44.jpg

Feb 13, 2011 | 2005 Ford Escape

1 Answer

When i jack car up rear wheel shakes on 2005 camery


Does it give a problem when driving? The lug nuts could be loose or it could have a problem with the wheel bearing. This Is is assuming you mean the wheel itself can be moved and not the strut assmebly. Since I also drive a 2005 Camry I am curious about the details. Does the wheel moe on the hub or does it stay tight and the whold assembly allow moement?

Dec 12, 2009 | 2004 Toyota Camry

1 Answer

Car shakes when i put it in drive or reverse


1 Inspect Wheel Hub Bearing Worn, Dry or Damaged Wheel Hub Bearing. 2 Inspect Wheel Bearing-Rear Worn, Dry or Damaged Wheel Bearing.

Jul 02, 2009 | 1993 Toyota Camry V6

2 Answers

My camry is making a loud whining noise. I took it to a mechanic and he said it was probably the front bearings. The noise only happens when the wheels are spining. My question is how do I replace these....


Hi there. Most, if not all front wheel bearings these days are pressed into the front wheel hub assembly and to replace these is not normally a DIY job. Because new bearings need to be pressed into the hub assembly, a machine shop press ought to be used and the job undertaken by competent individuals. My advice if you do intend undertaking the work yourself is to remove the hub assembly and then have a machine shop operative remove the old bearings and have the new bearings pressed-in for you. Hope this helps, Scottech.

Jul 02, 2009 | 1996 Toyota Camry

1 Answer

How to change a rear wheel bearing on a 1994 toyota camry


The rear wheel bearing on a toyota camry is replaced by replacing the wheel bearing and hub as a unit. this is a design change as compare to older models with two piece wheel bearings. Scotch drive wheels. Remove rear wheel. Remove rear brake drum. (note: if emergency brakes are applied you will not be able to remove brake drum) Remove dust cap and hub retaining nut. Hub should slide off as unit. Replace hub with new unit. Installation is reverse of removal.

May 30, 2009 | 1994 Toyota Camry

1 Answer

How to change rear wheel bearings on 1992 toyota camry


remove the wheel, disconnect the a arms upper and lower, tie rod end,brake caliper, remove the hub, remove wheel bearing, replace, repack, and re install

May 28, 2009 | 1992 Toyota Camry V6

1 Answer

Need instruction manual/schematics for replacing 2005 kia rio driver side rear wheel bearing. i've got the wheel/hub/bearing off, not the inside ring to the bearing. i need to know how to replace it .


clean all the grease if there is any out of the hub, turn the hub over and using a drift and hammer strike the shell from the back edge working around the shell as you go, should not take too much to remove it but you will need a bit more than a tap with the hammer.
Hope this has helped you

May 22, 2009 | 2003 Kia Rio

1 Answer

We are trying to replace my rear wheel bearing. Can anyone give any ideas how to get it apart?


here is how to replace it on a 2 wheel drive please do not forget to rate and comment about your experience today. 2-Wheel Drive
  1. Before servicing the vehicle, refer to the Precautions Section.
  2. Remove or disconnect the following:
    • Negative battery cable
    • Rear wheel
    • Rear brake drum
    • Wheel hub nut
    • Wheel hub
    • Inner wheel bearing race from the hub
    • Snapring
    • Wheel bearing outer race from the knuckle

06017-esca-g92.gif
06017-esca-g93.gif
06017-esca-g94.gif
06017-esca-g95.gif 06017-esca-g96.gif

To install:
  1. Install or connect the following:
    • Wheel bearing in to the knuckle
    • Snapring
    • Wheel hub into the wheel bearing
    • Wheel hub nut. Torque the nut to 214 ft. lbs. (290 Nm).
    • Brake drum
    • Rear wheel
    • Negative battery cable
06017-esca-g97.gif
06017-esca-g98.gif

Apr 11, 2009 | 2005 Ford Escape

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

295 people viewed this question

Ask a Question

Usually answered in minutes!

Top Honda Experts

yadayada
yadayada

Level 3 Expert

76109 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Kevin Daniels

Level 3 Expert

1455 Answers

Are you a Honda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...