Question about Ford Cars & Trucks

1 Answer

The dash lights on one side work but not the other on my 1997 ford explorer xlt

Dash lights not working properly

Posted by on

  • g_aguilar296
    g_aguilar296 Jan 16, 2013

    the fuses are good, whats next??

×

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that hasĀ over 10 points.

  • Expert
  • 80 Answers

There are small replaceable bulbs behind the instrument cluster, they are installed in twist lock sockets usually, you have to pull the instrument panel to change them, #194 is a common dash bulb

Posted on Jan 16, 2013

3 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 25 Answers

SOURCE: 1996 Ford Explorer XLT abs light comes on on

The ABS light is for the Anti-lock Braking System. The MIL will illuminate if there is a difference in wheel speed sensors signals to the PCM. So you might have a wheel speed sensor that is going out on you. Does the light come on at low speeds, or just higway speeds? You could take the vehicle to a local parts store and have them pull the codes for you and that will tell you which speed sensor is out of whack. Also road grime, dirt and gunk buildup can cause speed sensors to give false readings. Hope tihs helps you out.......

Posted on Oct 22, 2009

  • 416 Answers

SOURCE: 2007 FORD EXPLORER XLT

need to set tires at correct pressure you can find a sticker on the inside of drivers door to tell you the correct pressure after you do that it sould reset the light after you drive

Posted on Feb 02, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

What ford explorer 1999 xlt fuse for brake light located


they are clearly marked on all makes, the panel should be under the dash on the drivers side, and the fuse will be maked as to what amps it should be to,.

Jun 15, 2014 | 1999 Ford Explorer

1 Answer

1997 ford explorer xlt. max ac works fine but when i switch to normal ac or change vent control it blows out heated air. How do i check or repair?


The blend door actuator is probably bad in it causing the warm air to blow out instead of cold air. It is behind the dash.

It may take several hours for a technician to get at it and replace the parts required for it to work again.

Aug 19, 2010 | 1997 Ford Explorer AWD

1 Answer

1997 Ford Explorer XLT V8 5.0L Check engine


ok you can take the egr valve off and clean it and if that works you my need to take it to get reset on codes other then that also check vacum lines if these do not work you will have to replace and i hate saying that because this part is high.. good luck to you and have a blessed day..

May 13, 2010 | 1997 Ford Explorer AWD

3 Answers

1997 ford exibition xlt my interior light and running board lights wont go off along wiith the door ajar light on dash board. please help


Take some WD40 and open the doors and spray a liberal amount into each of the door latches. Then open and close the doors firmly several times. This will work most of the time to unstick the ajar switches.

May 24, 2009 | 1997 Ford Expedition

1 Answer

Need help finding fuses for dash lights on 1995 ford explorer


the fuse panel is on the drivers side of the dash between dash and drivers door

May 02, 2009 | Ford Explorer Cars & Trucks

1 Answer

2006 Ford Explorer XLT the Blower Fan only works on 4 and 3 Sp


Look under the dash on passenger side and just to the left of the blower motor housing you will see the 4WD control module.Remove the 2 screws holding the module and let it hang down and your resistors are behind this.Remove the 2 screws holding the resistors and remove.
Now I am assuming you have manual climate control and not electonic.

Feb 25, 2009 | 2006 Ford Explorer

1 Answer

I can't find the inertia switch on my 1992 ford explorer xlt


usually on fords the inertia switch is on the passenger side up under the dash on the firewall, not positive on the explorer but on other fords i have worked on that is the location.

Feb 14, 2009 | 1992 Ford Explorer

1 Answer

Airbag passenger side


44 - Right Hand Radiator Primary Crash Sensor Not Mounted to Vehicle Properly.

When the Airbag light is blinking, your airbag is disabled and many insurance companies now do a diagnostics on any failed safety equipment in injury accidents....they will not pay 100% percent if there is owner's negligence to maintain vehicle safety equipment. I am still looking into possible causes for this error. I will post any updates as warranted.

May 31, 2008 | 1997 Ford Explorer AWD

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

117 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

75744 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

fordexpert

Level 3 Expert

5495 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...