Question about 2006 Chevrolet HHR
Mirrors were working before I had service this A.M.. My ac fan motor was replaced and my key fob was replaced.
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Posted on Jan 02, 2017
you need to cut out the bottom of the box where the motor sits and get an blower motor attachment kit from local gm dealer
Posted on Jun 19, 2009
SOURCE: passenger side mirror
If you need to replace the entire mirror - it's a little involved. First you need to take the upper extension panel off from behind the mirror (black triangle) - just pull it of starting at the top. It will snap back on later. Next - remove the different screws holding the door panel in place (not the ones behind the mirror yet!) One is under the handle (pull it out and pull out the filler panel - small plastic thing that has a hole to pry it out). Then take off the rear red light - also pops off - and remove that screw. Finally - pick up the rubber filler where your fingers pull the door shut and remove these torx bolts.
Now is the tricky part. Snapp off the entire interior panel. It will pop off - but very difficult. It will sound like it is breaking! Start at the outer bottom corner - and use a door panel remover tool - check Amazon or E-bay - to keep from breaking things. Pull it out from all around the bottom and sides and then lift it up over the door lock. It good to have a friend help here. The panel will still be held on by a cable - that is your door release - leave it alone and let the panel hang by it (or better, put a box under it to rest on).
Now...remove the three bolts holding the mirror on - have a friend help hold the mirror while you do this or it will scratch your new car! Since the inner panel is off - you can also disonnect the mirror plus and remove it. It sounds silly - but the only reason to remove the door panel is to unplug it!
Get you new mirror and reverse the steps.
If you are just replacing the glass (non-heated) - get a replacement from the dealer. Adjust the mirror all the way to the inside and reach behind and pop it off. CAREFUL - put tape over the entire glass as it will likely break even more! Remove your connectors if heated - and replace (and reconnect) with your new glass. It just pops back on!
Replacing glass is easy - just be careful of cheap imitations on e-abay). And never use cheap flat glass on the passenger side! The DOT has special requirements for mirror glass - buy it from gmpartsdirect.com or your local dealer.
Posted on Jan 08, 2009
It should snap out and the new one snap in. Most auto glass companies can order just replacement glass from burco mirror. http://brokencarmirror.com/replacement/mirrors/
Posted on Feb 23, 2009
On the inside trim, you can remove screws that are by the door handle, arm rest, under door and side of door and then gently pull back on the panel as there will also be retaining clips attached and you don't want to break them. You'll need to lift the door panel upwards in order to get it off the window ledge. Then you'll need to manipulate the panel and disconnect the door handle linkage from the door handle and disconnect the wiring for your controls. Then you can access the bolts that secure the mirror onto the door
Posted on Sep 29, 2009
Tips for a great answer:
Aug 28, 2016 | 2008 Chevrolet Chevrolet HHR LT
Dec 31, 2013 | 2006 Saab 9-3 2.0T
Apr 10, 2013 | 2006 Lincoln Navigator
May 24, 2011 | 2006 Ford Escape
Jan 31, 2011 | Toyota Camry Cars & Trucks
Aug 22, 2010 | 2006 Dodge Grand Caravan
Jul 19, 2009 | 2002 Toyota Camry
Jan 20, 2009 | 1998 Jeep Cherokee
41 people viewed this question
Usually answered in minutes!
Step 2: Please assign your manual to a product: