Question about Mercedes-Benz E320

Open Question

Where is the camshaft sensor located on a 2004 c240 mercedes

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad
  • 3 Answers

SOURCE: Cam Shaft Sensor Problems

Had the same problem before on my 04 Neon SXT...camshaft sensor is on left side of engine block, take out the battery and to the left of it (face car) is the camshaft position sensor. To change it you'll have to move a few hoses but its plan to see there on the left side of the engine...pretty easy remove and replace. Fixed my problem of car not going above 2k RPM when i replaced the sensor.

Posted on Dec 29, 2008

Ad
  • 1 Answer

SOURCE: Replace Cabin Filter in my 2002 C240 Mercedes Benz

I have a 2002 C240 Mercedes and need to replace the cabin air filter. Problem, I don't know were it is located or how to replace it. Can you help me.

Posted on Mar 21, 2009

dttech
  • 4803 Answers

SOURCE: where is the camshaft positioning sensor located

Your 2004 Nissan Quest is most likely to be equipped with a 3.5L V-6 engine. This engine has 2 Cam (PHASE) sensors. One is located in the back of each cylinder head. You must remove your intake air duct to see them.

Posted on Oct 17, 2009

johnjohn2
  • 5763 Answers

SOURCE: Need to know where the camshaft position sensor is

if you stand on the passengerside looking at motor the sensor is located to the left of the timing belt cover near the top of the motor.hope this helps.

Posted on Jan 04, 2010

  • 151 Answers

SOURCE: Location of camshaft position sensor on 2004

On 1999 and later 2.4L SOHC engines it is located on the left end of the cylinder head (opposite end of the engine from the timing belt)

Posted on Mar 10, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Where is the transmission control module for a 2002 Mercedes benz c240


it is integral to the transmission , i've put a link to a video , shows the basic procedure so you will know if it's something you could do or get a mechanic
Mercedes Benz Transmission Control Module Replacement

Apr 08, 2015 | Cars & Trucks

1 Answer

2004 Mercedes c240 won't start, turned the


It is located on the transmission where the sghift cable connects to the transmission.

Jun 12, 2013 | Cars & Trucks

1 Answer

Stepped on gas on my 2004 mercedes c240 and no acceleration then engine light came on, whats going on ?


If the sensor in the pedal value sensor fails the system,switches over to the second one .The throttle will be limited to 60%. A electronic throttle acuator will be the solution

Mar 28, 2012 | Mercedes-Benz C240 Cars & Trucks

1 Answer

I have a 2004 mercedes c240 and have a new crank censor to install. Where is the censors location on the 6 cylinder?


Pretty sure the sensor is on the top of the gearbox bellhousing, and picks up its pulse from the flywheel on this model, its held in by allen bolts and is easiers to access from underneath the vehicle ( just above starter location

Sep 19, 2010 | Mercedes-Benz C230 Cars & Trucks

1 Answer

How do I stop my alarm from going off


UN HOOK THE ALARM WIRE THAT GOES TO ALTERNATOR

Jul 21, 2010 | 2004 Mercedes-Benz C-Class

1 Answer

Is a 2004 mercedes benz c240 a remote control key? If so, where is it located?


If you mean has remote got a emergency key
Look on top of remote for small catch, slide and pull out key

Mar 01, 2010 | 2001 Mercedes-Benz C-Class

1 Answer

How To Change Oxygen Sensors in 2002 Mercedes C240 Sedan?


I do not know the part numbers but you have 4 sensors. 2 pre and 2 post catalytic converter. The pre sensors are the most sensitive and are generally the ones to fail. the rear sensors usually have a heater circuit problem. If your just replacing them for routine service interval I would just do the fronts. They connect to the engine wire harness in the front of the transmission pan. You may need an o2 sensor socket to remove the fronts. They are just a 22mm. in size.

Oct 17, 2009 | 2002 Mercedes-Benz C-Class

1 Answer

2004 mercedes c240 alarm sounds for no apparent reason


Hi, You need to replace the alarm siren. It is also a module. It is located in the right front fender well. The reason they go bad is because they are located in a place where they get wet.

Apr 03, 2009 | 2004 Mercedes-Benz C-Class

1 Answer

2005 Mercedes C240; looses power and check engine light comes


better to bring your car to dealer to avoid replacing part.,better to check air mass sensor or idling actuactor.

Feb 10, 2009 | 1995 Mercedes-Benz C-Class

1 Answer

Crankshaft position sensor replaced and car shuts off


Hello, The crankshaft sensor is located at the left rear of the motor, behind the left cylinder head where the transmission bolts up. I believe that it has a 6mm allen head screw holding it down.
I hope this helps.
CYA, Gator241

Nov 12, 2008 | 2001 Mercedes-Benz C-Class

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

85 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mercedes-Benz Experts

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

yadayada
yadayada

Level 3 Expert

76109 Answers

Michael Contreras
Michael Contreras

Level 2 Expert

166 Answers

Are you a Mercedes-Benz Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...