Question about 1998 Isuzu Rodeo

Open Question

How many teeth between marks on rodeo 6ve1 timing belt

V6 rodeo, how many teeth between marks on timing belt

Posted by Anonymous on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

blueextc3221
  • 15935 Answers

SOURCE: need diagram for timing belt setting and alignment

CLICK HERE
for a BOATLOAD of info.

Thanks for using FixYa - a FixYa rating is appreciated for helping with your problem.

Posted on Apr 17, 2009

honeymokey
  • 3113 Answers

SOURCE: won't start after timing belt has been replaced

The cam pulleys turn 3 or more turns to one of the camshaft. You need to find someone that is experienced on this vehicle. Just aligning marks does not mean its in sync.

Posted on May 13, 2009

stevenhurc
  • 450 Answers

SOURCE: trouble getting marks aligned on 2001 Izusu Rodeo

if its a 6VE1 engine you might want to remove rocker covers and put front lobes of camshafts in position shown in picture with cam gear timmed up at same point cam gear are 3:1 ratio


b76b855.jpglook closely at cam gears in pic to see front lobe positions for both banks

Posted on Jul 30, 2009

  • 31 Answers

SOURCE: 2001 isuzu rodeo v6 3.2

Go to parts store get manual that will tell you a lot better then it can be explained

Posted on Nov 02, 2009

  • 270 Answers

SOURCE: I would like a diagram of a V6 timing belt

In the US the public library should have an auto repair data base that you can access with your library card number. If not you could always go there and check out a real book.

Posted on Dec 24, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

On a 1999 Isuzu Rodeo 3.2 V6 DOHC If you put all timing marks together on engine and then put timing belt mark all together on the engine and rotate two rounds with crankshaft does all the marks come


Just the engine. The marks on the belt are to make sure the teeth are in the right place when replacing. It might come back in place on 4 turns of the crankshaft. I have never checked to see if the belt marks came back. But always check the timing marks themselves.

Hope this helps.

Nov 10, 2014 | 1999 Isuzu Rodeo

Tip

Isuzu serpentine belt routing diagram for 6VE1, 6VD1, Rodeo, Trooper and Axiom...


Serpentine belt routing diagram for an Isuzu V6 cylinder engine. 6VE1, 6VD1 as fitted to Rodeo, Trooper and Axiom
4b4418d.jpg

  1. Crankshaft pulley
  2. Tensioner
  3. Alternator
  4. Idler pulley
  5. Power steering
  6. Airconditioning compressor
  7. Cooling fan pulley

on Sep 07, 2010 | Isuzu Trooper Cars & Trucks

1 Answer

Turns over but no spark, after new head askets


are you asking this 3 times removed? really>????
is this the 4 cam v6 or 2?
the 4 cam has 2 gears for 2cams and belt drive. 6ve1
the 2 cam v6 has no gears.
6ve1 engine, they have real names and all run different EFI controls
all do.

ok no spark (tested the wrong way !!!)
fuses good. or not, we test them not guess, on (looks ok)
you need to run compression on any engine with new head (or pulled) or leakdown 10x more safe.
that be first. you can bend valves on the 4 cam engine
(not on 2valve engines,one per bank)
forget the 2 CMP sensors on rear of both heads.?
spark dead on all 6 spark plugs
ckp dead.
CMP 1 or 2 dead
fuse blown.
has 6 ignition coils right, (usa) called C.O.P.'S.

i bet you didnt scan it cranking did you
if the pcm on the 6ve1 engine, sees cams turn wrong
it cuts spark to keep from bending over the head valves
the cams must be timed correctly and not in a cavalier manor
what's your engine vin code 8th digit
that tells the helper what engine is there, as you seem not to know.
there are 3 different V6 used here.

i see you really didnt check spark, just assumed it.
why? extend one cop, use fresh grounded test spark plug
omg got spark omg on all 6 in fact
omg compression is dead. x6 bent valves.

i never ever ever, crank any DOHC engine (messed with like this)
until the leak down test passes, by hand with shop air.
this act,saves further damage

VIN = Y or W
eight digit of vin is engine code. !!!
are 4 camsl

its flooding
so, compression is gone
sparks gone
or it over injecting for some reasons
if compression is ok, 150psi +
and parks good
secret wide open throttle will clear floods, (cut fuel mode )
but all this is risky on any 4 cam interference engine.

when i put the belt back (assuming cams not removed)
I check cam timing 2 time or 3 times, or risk bending valves.
6ve1
then do the leak down test now, just like you are there.
hand turned crank. (at each of the 6 TDC points(skills)
opps its got 0psi on many cylinder
that means valves are bent.

here is the SM quote step 4 belt install
WARNING If any binding is felt when adjusting the timing belt tension by turning the crankshaft, STOP turning the engine, because the pistons may be hitting the valves.
one can just throw an engine like that back together.
they also told you to set cam timing first, before pulling heads
or damage can happen,
but that depends on the event
belt snapped, jump cogs or just leaking head gasket.

Mar 02, 2017 | 2000 Isuzu Rodeo

1 Answer

Where is the location of camshaft sensor 1998 isuzu trooper


if its diesel 4JX1 its in top cam belt cover cant miss it, sensor is very clearly visible.
if its petrol V6 (6VD1 or 6VE1) its in left head at rear behind inlet manifold
these pictures are for petrol V6, Jackaroo(Trooper) and Holden Rodeo are the same.

stevenhurc_21.jpg



stevenhurc_22.jpg

Apr 10, 2011 | 1998 Isuzu Trooper

1 Answer

I have a 3.2lt dohc V6 holden redoe i finished rebuilding the head after i blew a head gasket. i think there is a problem with the timing but i have followed the haynes repair manual which told me that...


it sounds like the timing belt may have moved of the crank shaft timing gear one or two teeth ,this can happen when working with the belt tensioner you should reset all the timing marks and make sure nothing moves when the belt is retensioned

Apr 11, 2010 | 1998 Isuzu Rodeo

1 Answer

Replace timing belt &head started once ran good but would not restart replaced wiree &coil but won't start and run


I would recheck your timing marks and make sure the belt didn't jump a few teeth, This happens once and a while.

Good Luck.

Oct 06, 2009 | 2002 Isuzu Rodeo

1 Answer

Can i take a 2000 rodeo motor and put it into a 2001 rodeo without changing the ecu


yes motors are same for both years if V6 they both are 6VE1 engines
just leave engine ECU in original vehicles

Aug 13, 2009 | 2001 Isuzu Rodeo

1 Answer

Trouble getting marks aligned on 2001 Izusu Rodeo


if its a 6VE1 engine you might want to remove rocker covers and put front lobes of camshafts in position shown in picture with cam gear timmed up at same point cam gear are 3:1 ratio


b76b855.jpglook closely at cam gears in pic to see front lobe positions for both banks

Jul 29, 2009 | 2002 Isuzu Rodeo

Not finding what you are looking for?
1998 Isuzu Rodeo Logo

Related Topics:

85 people viewed this question

Ask a Question

Usually answered in minutes!

Top Isuzu Experts

yadayada
yadayada

Level 3 Expert

75066 Answers

Steve Hurc
Steve Hurc

Level 3 Expert

450 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Are you an Isuzu Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...