Question about Ford Freestar

1 Answer

Where is tCC sylanoid located at 2001 Ram - Freestar Ford Cars & Trucks

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

  • Contributor
  • 22 Answers

In the valve body under the trans pan then the valve body needs to be remove . make sure you check the position of the gasket and the style there will some times be more then one . but position is the most important. put the new gasket in wrong and yuo will be doing the job again . u will no when t he vehicle does no go in any gear, replace the filter when you are in there

Posted on Jan 16, 2013

2 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

bonedivers
  • 1140 Answers

SOURCE: p1740 code on 2001 ram

there is a total of 27 diagnostic steps to follow, but here is some info for you:
SYMPTOM
P1740-TCC O/D SOL PERFORMANCE

WHEN MONITORED
The Torque Convertor Clutch (TCC) and Overdrive Clutch (O/D) will be tested each time the PCM requests TCC engagement in 3rd gear and O/D.

SET CONDITION
The code will set if the expected RPM drop is not achieved while attempting to engage TCC or O/D. This indicates a malfunctioning torque convertor or overdrive clutch.

POSSIBLE CAUSES
- Camshaft DTC present
- Engine RPM DTC present
- Fuel level low
- Misfire DTC present
- Output speed DTC present
- P1765 DTC present
- Park/Neutral DTC present
- PTO engaged (if equipped)
- Torque converter clutch DTC present
- TPS DTC present
- Transfer case in low range (if equipped)
- Transmission Relay DTC present
- Transmission temperature too cold
- Intermittent
- Check transmission fluid-debris
- Check transmission fluid-stall
- 3-4 Shift Solenoid
- Oil Pan contains excessive debris
- Shaft or seal damage
- TCC solenoid
- Torque converter
var classElements = new Array(); var node = document; var tag = 'a'; var els = node.getElementsByTagName(tag); var elsLen = els.length; var pattern = new RegExp("(^'\\s)specs_note(\\s'$)"); for (i = 0, j = 0; i

Posted on Jun 04, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Where is the tcc selenoid location on a 2001 isuzu trooper gm4l30e transmission? im trying to replace this part due to a p1860 error code which is 'torque converter clutch selenoid circuit failure'


the transmission is super common GM box.
no lack free books ever google, 4L30 yet>

TCC has 2 parts not just one, 3 counting the TCM driver.
and 4 counting wire to and from.
the TCC lock is solenoid lock.
http://www.makcotransmissionparts.com/4l30e.html

http://www.makcotransmissionparts.com/mm5/graphics/Catalog-pdf/4L30E.pdf



the device below is just 1/2 half the path, to the actual lock.
the TCM engages this part below and it sends pressure to the
actual lock.either can fail, so can TCM.
its in the transmission.
the valve body.
the question really is which pan tiny or big.
2 in the front (here) see photo at end
3 in the rear, VB. not here total 5
the TCC on this car is PWM type. (modulated 2000+)

shows the conversion and how it all works too. all on one page.
http://www.atraonline.com/gears/2006/2006-03/2006-03_4.pdf

tcc-cumberlcvpguaemnsvjvleah-1-0.jpg

sol-tcc-cumberlcvpguaemnsvjvleah-1-1.jpg

Mar 05, 2017 | 2001 Isuzu Trooper

1 Answer

What is tcc selenoid


TCC is a Torque Converter Clutch, is located in the transmission

Mar 30, 2013 | 2001 Mazda MPV

1 Answer

P1740 code on 2001 ram 1500 tcc-overdrive solenoid . how to test & replace


there is a total of 27 diagnostic steps to follow, but here is some info for you:
SYMPTOM
P1740-TCC O/D SOL PERFORMANCE

WHEN MONITORED
The Torque Convertor Clutch (TCC) and Overdrive Clutch (O/D) will be tested each time the PCM requests TCC engagement in 3rd gear and O/D.

SET CONDITION
The code will set if the expected RPM drop is not achieved while attempting to engage TCC or O/D. This indicates a malfunctioning torque convertor or overdrive clutch.

POSSIBLE CAUSES
- Camshaft DTC present
- Engine RPM DTC present
- Fuel level low
- Misfire DTC present
- Output speed DTC present
- P1765 DTC present
- Park/Neutral DTC present
- PTO engaged (if equipped)
- Torque converter clutch DTC present
- TPS DTC present
- Transfer case in low range (if equipped)
- Transmission Relay DTC present
- Transmission temperature too cold
- Intermittent
- Check transmission fluid-debris
- Check transmission fluid-stall
- 3-4 Shift Solenoid
- Oil Pan contains excessive debris
- Shaft or seal damage
- TCC solenoid
- Torque converter
var classElements = new Array(); var node = document; var tag = 'a'; var els = node.getElementsByTagName(tag); var elsLen = els.length; var pattern = new RegExp("(^'\\s)specs_note(\\s'$)"); for (i = 0, j = 0; i

Jun 03, 2011 | Dodge Ram 1500 Cars & Trucks

1 Answer

My 2007 dodge with 5.9 diesel is showing engine malfunction light and error code of P1740, failed TCC or overdrive solenoid. The truck seems to run ok in overdrive but I don't understand what the TCC...


Code P1740-Torque converter clutch did not lock up when the PCM sent the command. Enabling conditions: No engine or transmissions codes are present, vehicle speed was under 70 MPH, TPS was under 33% open. When the PCM commanded the torque converter to lock, no change was detected in engine speed. Blocking action: This code can block the following monitors: none.

Testing: Check torque converter solenoid for proper operation.

NUMBER: 21-11-00
GROUP: Transmissions
EFFECTIVE DATE: October 02, 2000
SUBJECT: 46RE Transmission MIL Due To DTC P1740 - TCC or OD Solenoid Performance
OVERVIEW: This bulletin involves the replacement of the transmission pressure boost valve cover plate.
MODELS: 2000 - 2001 (AB) Ram Van 2000 - 2001 (AN) Dakota 2000 - 2001 (BR/BE) Ram Truck 2000 - 2001 (DN) Durango

NOTE: THIS BULLETIN APPLIES TO VEHICLES EQUIPPED WITH A 46RE TRANSMISSION BUILT BEFORE AUGUST 01, 2000 (MDH O8O1XX).

SYMPTOM/CONDITION:
The customer may complain of a Malfunction Indicator Lamp (MIL) illumination. Upon further analysis, it is determined that the MIL is caused by Diagnostic Trouble Code (DTC) P1740 - Torque Converter Clutch (TCC) or overdrive solenoid Performance. Other than the MIL, the customer may not notice any other condition with the transmission.

This condition may be caused by an intermittent and momentary TCC disengagement condition. The transmission valve body pressure boost valve cover plate has been revised with a larger size orifice hole to address this condition.

NOTE: THE DRB III(R) MUST BE OPERATING AT RELEASE LEVEL 50.4 MDS2 SYSTEM CIS CD2067 OR HIGHER (AVAILABLE THE WEEK OF OCTOBER 2, 2000) IN ORDER TO PERFORM THE REVISED TORQUE CONVERTER CLUTCH STALL TEST. DO NOT USE EARLIER VERSION STALL TEST TO DETERMINE CONDITION OF THE TORQUE CONVERTER CLUTCH.

Here can find the test in pdf format: 2009-11-28_034958_1124.pdf

Hope helps.

Apr 28, 2011 | Dodge Ram 3500 Cars & Trucks

1 Answer

Where is the Transmission Solenoid Located for 2001 cadillac deville, inside or outside transmission. i have a transmission trouble code of p0741. Transmission runs good, it shifts normal as always. i...


The TCC solenoid is located inside the transmission. Replacing the solenoid usually does not fix the problem when it comes to a P0741 code. It is usually due to debris getting caught in the TCC regulator valve or the tubine shaft seals being worn out. This usually results in a transmission overhaul.

Dec 27, 2010 | 2001 Cadillac DeVille

1 Answer

Where is the transmission lock up selenoid located, on or in the transmission


The Powertrain Control Module (PCM) controls the Torque Converter Clutch (TCC) lock up.The TCC is engaged by the clutch solenoid located on the valve body which is accessible by dropping the pan on trans

Sep 02, 2010 | 2001 Dodge Neon

1 Answer

P1740 code came on for a 2001 dodge ram 1500 what does it mean?


This is the OD Solenoid. There is a TSB out that covers the 2000-2001 Ram truck.

EFFECTIVE DATE: Oct. 02, 2000
SUBJECT:
46RE Transmission MIL Due To DTC P1740 – TCC or OD Solenoid Performance
OVERVIEW:
This bulletin involves the replacement of the transmission pressure boost valve cover
plate.
MODELS:
2000 - 2001 (AB) Ram Van
2000 - 2001 (AN) Dakota
2000 - 2001 (BR/BE) Ram Truck
2000 - 2001 (DN) Durango
NOTE: THIS BULLETIN APPLIES TO VEHICLES EQUIPPED WITH A 46RE
TRANSMISSION BUILT BEFORE AUGUST 01, 2000 (MDH 0801XX).
SYMPTOM/CONDITION:
The customer may complain of a Malfunction Indicator Lamp (MIL) illumination. Upon
further analysis, it is determined that the MIL is caused by Diagnostic Trouble Code (DTC)
P1740 - Torque Converter Clutch (TCC) or Overdrive Solenoid Performance. Other than
the MIL, the customer may not notice any other condition with the transmission.
This condition may be caused by an intermittent and momentary TCC disengagement
condition. The transmission valve body pressure boost valve cover plate has been revised
with a larger size orifice hole to address this condition.
DIAGNOSIS:
1. Warm the transmission to normal operating temperatures.
2. Using the DRB IIIò, perform a torque converter clutch (TCC) stall test. The stall test
has been revised so that the TCC remains engaged for a period of four (4) seconds.
NOTE: THE DRB III MUST BE OPERATING AT RELEASE LEVEL 50.4 MDS2
SYSTEM CIS CD2067 OR HIGHER (AVAILABLE THE WEEK OF OCTOBER 2,
2000) IN ORDER TO PERFORM THE REVISED TORQUE CONVERTER
CLUTCH STALL TEST. DO NOT USE EARLIER VERSION STALL TEST TO
DETERMINE CONDITION OF THE TORQUE CONVERTER CLUTCH.
3. If the engine stalls as a result of the TCC stall test, then perform the Repair
Procedure.
4. If the engine does not stall, as a result of the TCC stall test, then further diagnosis is
required. The technician may want to consider the following components during
their additional diagnosis: a cut or worn input shaft seals, a missing pump lock-up
circuit check ball, or worn converter hub, input shaft, reaction shaft, and pump rotor.
This bulletin is supplied as technical information only and is not an authorization for repair. No part of this publication may be reproduced, stored in a retrieval system, or
transmitted, in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, without written permission of DaimlerChrysler Corporation.
21-11-00 -2-
PARTS REQUIRED:
1 04617015 Plate, Pressure Boost Valve Cover (46RE)
1 02464324AB Gasket, Trans Pan
10(AR) 05010124AA ATF+3, Transmission Oil Type 7176 (2000 M.Y.)
10(AR) 05013457AA ATF+4, Transmission Oil Type 9602 (2001 M.Y.)
REPAIR PROCEDURE:
1. Clean the pressure boost valve cover plate to remove any dirt or rust inhibitor prior to
installation. The revised cover plate will have a 1.75 mm (0.069 inch) orifice hole
versus a 1.22mm (0.048 inch) orifice hole in the original plate. Make sure it is clean.
2. Using the appropriate Service Manual, Group 21 – Transmissions and Transfer Case,
replace the transmission pressure boost valve cover plate p/n 04617012.
3. Verify fluid level after warming up the transmission and cycling the shift lever several
times.
4. Verify, and if required, adjust the transmission shift linkage and the transmission
throttle valve cable per the appropriate Service Manual procedures.

Jun 10, 2010 | 2000 Dodge Ram 1500 Truck

1 Answer

I have a 2001 Saturn SL2 and need to know thelocation of the tcc solenoid. Can U help?


TCC solenoid is located in the valve body on top of the transmission. Once you have the valve body top removed, the TCC solenoid is the third one from the left.

Hope this helps.

May 20, 2010 | 2001 Saturn SL

1 Answer

Pontiac 2001 tcc replacement


i have an 2002 grand prix gt with a bad tcc silinode sensor dont knoow where its located at...anyone that can tell me would be great

Mar 23, 2010 | 2001 Pontiac Grand Prix

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

27 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

75051 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

fordexpert

Level 3 Expert

5470 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...