Question about 2007 Ford Explorer Sport Trac

1 Answer

2007 ford sport trac will not crank but has power to starter

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Greenhorn:

    A rookie expert who has answered 20 questions on their first day.

    Cheetah:

    An expert who has answered 20 or more questions within one hour.

  • Expert
  • 93 Answers

The solenoid is just a big switch. If it is not working the starter will not engage which means you might have a bad solenoid or a bad motor.

Posted on Jan 15, 2013

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
chuck943
  • 783 Answers

SOURCE: 2007 FORD EXPLORER SPORT TRAC 4X4 Change oil light on

Press and hold the SELECT/RESET
control switch to select SYSTEM
CHECK when “SYSTEM CHECK /
HOLD RESET” is displayed in the
message center. Selecting this
function from the SETUP MENU
causes the message center to cycle through each of the systems being
monitored. For each of the monitored systems, the message center will
indicate either an OK message or a warning message for two seconds.
Pressing the SELECT/RESET control switch cycles the message center
through each of the systems being monitored.

The sequence of the system check report and how it appears in the
message center is as follows:
1. OIL LIFE RESET
2. CHARGING SYSTEM
3. WASHER FLUID
4. DOOR AJAR
5. EXTERIOR LAMP
6. BRAKE SYSTEM
7. PARK BRAKE
8. MILES TO EMPTY
9. FUEL LEVEL LOW (will only display if 50 miles or less to empty)
To reset the oil monitoring system to 100% after each oil change
[approximately 5,000 miles (8,000 km) or 180 days] perform the
following:
1. Enter SYSTEM CHECK to display
“OIL XXX% RESET IF NEW”.
2. Press SELECT/RESET control
switch to display “HOLD RESET IF
NEW OIL”.
3. Press and hold the
SELECT/RESET control switch for
more than 2 seconds. Oil life is set
to 100% and “OIL CHANGE SET TO
100%” is displayed.

Posted on Apr 02, 2009

  • 148 Answers

SOURCE: Ball joint replacement-2003 Ford Sport Trac

if you dont have a ball joint press and dont know how to use one then dont do it, but if you do its not that bad of a job just jack the truck up under the control arm remove the brake rotor then take the lower ball joint nut off then use a pickle fork to break the ball joint loose then take the axle nut off push the axle out of the bearing and use the ball joint press to remove and replace the ball joint

Posted on Jul 19, 2009

  • 9 Answers

SOURCE: Change the brakes on 2007 sport trac

it has front and rear disc brakes, disc brakes are very simple to change out. Most disc brakes have two bolts that hold them on, one on the bottom one on the top on the inside of the brake caliper, they may be an allen head, or just a bolt. Remove them counter-clockwise. After you remove the two bolts, lift up and away on the caliper and the whole assembly will come off. Once you pull the assembly off you will see the two pads, one of them is driven by a piston, the other one is fixed. Remove the fixed one, they just pop off (have little metal clips you may have to slide the pad off). Take a C-clamp or something comparable to squeeze with, place it on the back of the caliper and on the old pad thereby squeezing the cylinder back into the piston, once you squeeze the cylinder back into the piston, it will give you room needed for thicker new brake pads. Piston should retract with the c-clamp fairly easy, shouldn't be a whole lot of resistance. Remove c-clamp after you get it to retract and remove old pad. Put new pad on, just like you took the old ones off. All four are basically the same to change out, they all have two bolts holding them on. You pull those, get the pistons to retract and replace the worn pads, put them back on, line up holes, put bolts back in... and your good to go. When you get back in the car and turn the key on, you may have to pump the brakes a few times.

Posted on Nov 02, 2009

  • 1 Answer

SOURCE: 01 ford explorer sport trac rear timing chain diagram

They will not loan you the tools.....how else will they continue to rip off the average garage junkie and make lots of money?

Posted on Nov 18, 2009

  • 5 Answers

SOURCE: how to replace fuel filter on 2001 ford sport trac

Buy a manual and read it. The manual will tell you how to replace...

Posted on Nov 23, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to replace headlight bulb on 2007 ford explorer sport trac


How To Install Replace Headlight Ford Explorer Sport Trac ...

? 4:28
https://www.youtube.com/watch?v=NzMVcCsZ860
May 11, 2010 - Uploaded by 1A Auto Parts
How To Install Replace Headlight Ford Explorer Sport Trac 01-05 1AAuto. .... We offer the replacement headlights on our website for your truck.

Jan 11, 2016 | 2007 Ford Explorer Sport Trac

1 Answer

2007 ford explorer sport trac will not crank but it has power to starter and everything else works


Solenoid, which is just a big switch might be bad, motor might be bad. If you have good access should be easy to troubleshoot. Doesn't sound serious.

Jan 15, 2013 | 2007 Ford Explorer Sport Trac

1 Answer

Sport trac fails to crank. Battery ok. Changed starter but did not solve problem. What are other solutions?


There are a couple of things if you haven't checked them already. In the power distribution box located under the hood of the vehicle in the engine compartment there is a cartridge fuse and a starter relay. Below is a diagram of the fuse layout. The cartridge fuse is a 30 amp and is the one in the number 8 position and the starter relay is the one in the number 49 position. I have seen in many cases with Fords that if the starter has a short or it is trying to pull to much power it will blow the fuse. I hope this helps and good luck.


clifford224_383.jpg

Aug 27, 2011 | 2004 Ford Explorer Sport Trac

2 Answers

How often do I have to change the automatic transmission fluid of a 2007 explorer sport trac?


2007 Sport trac transmission is factory sealed and does not require fluid change.

Feb 04, 2011 | 2007 Ford Sport Trac Limited

1 Answer

2001 ford explorer sport trac wont start all the function turn on


check what the diagnosis machine will give if there is no data then check if the starter crank sensor is getting any power

Jul 26, 2010 | 2001 Ford Explorer Sport Trac

1 Answer

07 sport trac: wont start


check the starter solenoid, it is usaully bolted to the starter.

Aug 19, 2009 | 2007 Ford Explorer Sport Trac

1 Answer

Won't start


Check the battery cables make sure they are clean and tight. Make sure the battery has at least 12V, new batteries sit on the shelf for months sometimes before they are purchased. If this yields no results, remove the starter and have it checked. If it checks bad, replace the starter.

May 16, 2009 | 2007 Ford Explorer Sport Trac

1 Answer

2007 FORD SPORTS TRAC BATTERY KEEPS DYING


180 milli-amps is way to much draw,ford's limit is 50 milli-amps but typically we usually only see around 20-30. Now when you say fuse 2 is that in the under-hood fuse panel or the interior fuse panel? And if this vehicle is a 2007 it may still be under factory warranty which was 36 months or 36000 miles providing that the add on automatic starter is not causing your draw.Which in that case the people who installed it should be responsible for that.

Mar 05, 2009 | 2007 Ford Explorer Sport Trac

Not finding what you are looking for?
2007 Ford Explorer Sport Trac Logo

152 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

fordexpert

Level 3 Expert

5546 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...