Question about 1998 Buick Century

1 Answer

Hub assembly what tools do i need to change a hub assembly on a 1998 buick century mainly for the 3 mounting bolts

Posted by on


1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points


    An expert that got 20 achievements.


    An expert that got 10 achievements.


    An expert that got 5 achievements.

  • Buick Master
  • 6,674 Answers

This link may be of some assistance to you.

Posted on Jan 24, 2009


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

Replace the hub on a 2004 Buick Century

Jack up the car and remove the wgeel. Remove the two bolts holding the brake caliber on. Unplug the sensor lead. Remove the axle nut with the appropriatesized socket (usually 31 or 32 mm...can be rented at most chain stores). Slide axle out . Remove 3 bolts holding hub on. You can watch just about any wheel hub replacement video on YouTube and get a good idea of the procedure as all of them are similar. Reassembly is the reverse.

Oct 10, 2016 | 2004 Buick Century

1 Answer

How to change rear axle on 1998 town and country

This vehicle does not have a rear axle. It has 2 spindle hubs that are bolted into a housing with 4 bolts from behind the brake assembly similar to the hub assembly in the front except that the mount is static and has a spindle instead of a 1/2 axle joined to the transmission. To remove it, remove wheel, remove 4 bolt and and speed sensors if equipped with ABS brakes.. You may need to disassemble the brakes to get at the nuts & bolts.

Apr 04, 2015 | 1998 Chrysler Town & Country

1 Answer

Where can I find the special key to remove the hub caps from 1989 Buick century ltd to change tires

In the glove box should be a card with the ID information on which "colored" key needs to be ordered from a GM dealership. Otherwise you can go to a "parts" place, such as O'Reilly, NAPA, Big A, etc., and rent a universal removal tool to remove the bolt. Make sure to install a regular bolt back in when installing the cap or you will get a rattle and the hub caps will come off very easily.

Dec 20, 2014 | Buick Cars & Trucks

1 Answer

I Can Not Find The Thermostat On My 1998 Buick Century. Any Suggestions?

Locate the upper radiator hose. Follow it to the engine. Before it meets the engine, you'll notice that its clamped to a metal housing, usually mounted with 3 ten-millimeter bolts. This is the thermostat housing. Remove when engine is cool. Thermostat is inside. Remove old thermostat and replace ensuring the rubber o-ring aroung the outside of the thermostat if equipped. Good luck.

Sep 19, 2011 | 1998 Buick Century

1 Answer

How do I remove a 90-96 Buick Century wire spoke hubcap?

Center cap pops off. then there is a "special" tool to remove the bolts that hold the hub cap.

Apr 30, 2011 | 1994 Buick Century

1 Answer


Remove the brake caliper bracket bolts, there should be two of them. Pull the caliper assembly off of the rotor (you may need to depress the caliper piston by prying it inwards). Take the hub to axle nut off, and punch the axle inwards with a punch to loosen it up. Then remove the 3 bolts holding the hub in. One everything is removed, just hit the hub with a hammer until it falls off, clean off the mounting surface, and install the new one in reverse procedure.

Mar 27, 2010 | 1998 Buick LeSabre

1 Answer

How to replace rear bumper on 98 buick century . tools needed to remove and install new bumper.

A rachet, Some small metric sockets 7mm or 8mm a few larger metric sockets 13mm,15mm, phillips head screwdriver and tork bit screwdrivers and a set of metric wrenches may help also and a can of WD-40. Should be some screws in the wheel wells and 4 bolts on each mount for each side of the bumper.

Mar 12, 2010 | 1998 Buick Century

3 Answers

How to replace a transmission output seal 93 buick lesabre

you have to raise vechicle.use jack stands.block rear wheels.apply parking brake.when loosen axle nut.its more easier to leave wheel on.let vechicle weight hold wheel from turning while you loosen axle need to get a 1/2 break bar or large ratchett wrench with a deep socket .you need to buy socket use to remove axle nut a regular socket would probably break.when you remove the axle nut.remove brake caliper and brake pads.set them aside dont disconnect brake caliper.get a piece of wire to hang it out the way.dont use brake hose.could damage it. remove brake caliper support bracket then the rotor.get a hub removing tool remove hub.then loosen hub and bearings bolts .then remove shield hub and bearings assembly with O-ring.disconnect ball joint from steering knuckle using the proper tool.remove the halfshaft assembly and tap the seal from the steering knuckle.remove the steering knuckle from the that drive axle out the way.get the seal removing tool.its a flat tool with two hooks on pry seal out transmission.or you can use a small chisel to clapse the seal but be careful dont damage the seal housing.when installing new seal coat it with transmission it in using a large socket.if you are reusing same axle replace circlip on the end of putting back together.install a new hub and bearing seal in the steering knuckle with a seal installer tool .install steering knuckle to the strut.lubricate the hub and bearings with grease.install halfshaft.connect ball joint to the steering knuckle .install a new O-ring around the hub and bearing assembly.install hub and bearing assembly into the steering knuckle.tighten bolts to 75 ft lbs.install rotor then brake caliper support bracket bolts 120 to148 ft lbs.this is mounting bracket bolts only not the caliper bolts to brake shoes.put brake shoes and caliper back on torque 38 ft lbs.install shaft washer the axle nut to 180 ft lbs.tighten much as you can.before setting car on torque it to 180 ft lbs place car wheel back on set it down so the car weight keep wheel from turning.i hope this information works out for you good luck.and work safe.

Jun 27, 2009 | 1993 Buick LeSabre

2 Answers

Replace rear struts 1996 buick regal

Here is a link describing your strut replacement. Autozone also has free tool rental for the strut spring compressor if you need it. Thank you, and don't forget to vote.

Jan 29, 2009 | 1999 Buick Regal

1 Answer

Need to change struts front and rear on 2003 Buick Century

GET A SERVICE MANUAL !!! You'll need a spring compressuer. You can do it but, use care. And use a manual. If not done right you could be injured.

Jan 14, 2009 | 1996 Buick Century

Not finding what you are looking for?
1998 Buick Century Logo

Related Topics:

95 people viewed this question

Ask a Question

Usually answered in minutes!

Top Buick Experts


Level 3 Expert

76846 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6927 Answers

Are you a Buick Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides