Question about 2000 Honda Prelude

1 Answer

Yo I have a 1990 honda prelude si ,I have an issue with clutch pedal, my clutch pedal seems to stick when depressed it still has good pump pressure but I have to lift it up. Now I live in Idaho and it

Also unless I pull the pedal up before I shift gears I have a hard time shifting. But when I lift the clutch pedal and than depress it it seems to shift fine

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Honda Master
  • 5,252 Answers

The pedal return spring should be checked. Also the pedal bushings where pedal connects to the pedal support up under dash may be worn and not allowing free pedal movement. Work the pedal with your hand and watch the upper mounting of the pedal to see if you can see the problem. I would expect the bushings need replaced. You might try a little light oil where the clutch pedal attaches.

Posted on Jan 15, 2013

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

justuscc
  • 360 Answers

SOURCE: 2005 accord ex shift lock solenoid

its the brake switch....... i bet you dont have any brake lights......... its a switch by the brake pedal 14mm wrench measure the distance on the old switch on the threads good luck

Posted on Sep 17, 2008

  • 1596 Answers

SOURCE: rover 600 1997 not engaging any gears when clutch fully depressed

Sounds like the SLave Cylinder has givin up Possible the Reli=eice Bearing I ALWAYS Replace As A PAIR . If you can put in gear by having someone rock the car front to back and it holds well its pretty Obvious that you DO have A Clutch Master Cylinder or Clutch Slave aat Releice Bearing Problem AGAIN These Parts I REPLACE AS A PAIR. Before ANything Chech Fluid Level that will tell the store IF FULL Most Probably MASTER-- If EMPTY then See where it went Look At SLAVE if wet thats the Culpret. --->> I Hope this INFO helps you and have a good Day >> Please dont forget to RATE me ok ? Thank You

Posted on Jan 16, 2009

landsend
  • 1066 Answers

SOURCE: 2001 Honda Accord Clutch Issue

check the actual pedal and clutch linkage.  Also look for a fitting thats emitting air into the system.

Posted on Mar 24, 2009

  • 105 Answers

SOURCE: My Honda CRV-2000 manual transmission does not

the clutch fluid being low means that there is a leak in the hydraulic system and that is why you cannot get the vehicle in gear. even if you refilled the resivour you still need to fix where the leak is coming from then manually bleed out any air in the system. air is compressable and liquid is not. if there is air in the system you are only compessing the air when you push the clutch down and it is not pushing the clutch. check the clutch master cylinder for leaks- its under the clutch fluid. also check the slave cylinder is bolted the the transmission.

Posted on Jan 02, 2010

  • 2 Answers

SOURCE: 89 Accord LXI Idle problems

change all of your filters

Posted on Feb 27, 2012

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Engine revs but no acceleration


Clutch plate and pressure plate seem to be too weak to pull the car. Or one of the CV joints is detached from the gear box. To test the clutch plate, park the car on flat surface. Pull the hand brake up, start the car, depress the foot brake pedal, depress the clutch pedal, put the car in 1st gear, press the gas pedal and leave the clutch pedal at once, while keeping the brake pedal depressed.
Follow one of the two following statements:
1. Engine does not shut down and remain start. (Clutch plate, pressure plate and clutch bearing defective - Replace all as a set)
2. Engine shuts down. (Clutch system is OK and does not require any repair).

May 22, 2013 | Honda Civic Cars & Trucks

1 Answer

Car will not accelerate when gas pushed


Clutch plate and pressure plate seem to be too weak to pull the car. To test the clutch plate, park the car on flat surface. Pull the hand brake up, start the car, depress the foot brake pedal, depress the clutch pedal, put the car in 1st gear, press the gas pedal and leave the clutch pedal at once, while keeping the brake pedal depressed.
Follow one of the two following statements:
1. Engine does not shut down and remain start. (Clutch plate, pressure plate and clutch bearing defective - Replace all as a set)
2. Engine shuts down. (Clutch system is OK and does not require any repair).

May 22, 2013 | Honda Civic Cars & Trucks

2 Answers

My clutch won't engage 1997 Honda civic


Clutch plate and pressure plate seem to be too weak to pull the car. To test the clutch plate, park the car on flat surface. Pull the hand brake up, start the car, depress the foot brake pedal, depress the clutch pedal, put the car in 1st gear, press the gas pedal and leave the clutch pedal at once, while keeping the brake pedal depressed.
Follow one of the two following statements:
1. Engine does not shut down and remain start. (Clutch plate, pressure plate and clutch bearing defective - Replace all as a set)
2. Engine shuts down. (Clutch system is OK and does not require any repair).

Apr 06, 2013 | 1997 Honda Civic

1 Answer

How can i adjust the clutch in a honda prelude si 1991


i would ck oil as break fluid in clutch cyl then bleed the air.you have no other problems.good luck.

Feb 20, 2012 | 1991 Honda Prelude

1 Answer

My oil light is on in my 1987 honda prelude si. I recently changed the oil and oil filter. This problem came on after about a month of driving with fresh oil. My car is shuttering now and seems to be...


Best would be to check the oil pump filter in the sump of the engine. these also clog up and drops the oil pressure resulting in a warning light

Jun 28, 2017 | 1987 Honda Prelude

3 Answers

How can you tell if a 1992 honda prelude si fuel pump is going bad


Install pressure gauge and verify pressures and pumps ability to hold pressure once turned off

Sep 27, 2009 | 1992 Honda Prelude

1 Answer

I need to replace my speed sensor on my 90 prelude si


Look at the rear top of the gearbox/clutch bellhousing, below and behind the distributor. Well hidden, two bolts to fix, with a plug on the top.

Mar 28, 2009 | 1990 Honda Prelude

1 Answer

Replaced in/tank fuel pump.


I have had problems with my 89 prelude. I found that the problem wasn't with the fuel pump, rather the master relay. You will have voltage at the fuel pump with the fuel pump dicconnected, but when you connect the pump and put a electrical load on the circuit, the voltage drops. check current with the pump running and see if this is the case.

Jan 26, 2009 | 1990 Honda Prelude

2 Answers

Spark plug gaping


Go to your nearest Autozone or other parts house and buy an inexpensive plug gapper. I gap the Honda plugs at .045 .

Jun 16, 2008 | 1991 Honda Prelude

Not finding what you are looking for?
2000 Honda Prelude Logo

152 people viewed this question

Ask a Question

Usually answered in minutes!

Top Honda Experts

yadayada
yadayada

Level 3 Expert

75005 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7710 Answers

Are you a Honda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...