Question about Cars & Trucks

Open Question

Where are the tensioner bolts for 1993 mitsubishi mirage 1.8L L4 power steering belt?

Power steering

Posted by Anonymous on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

stevehinrich
  • 61 Answers

SOURCE: have a 1993 f250 with A/C, power steering. Is

There is a pulley on the tensioner but it may be best to replace the whole tensioner pulley assembly. There should be a bolt through the tensioner above the pulley. Once you remove that bolt you will be able to replace the tensioner.

Posted on Feb 26, 2009

c17hydro
  • 2984 Answers

SOURCE: need engine specs for mitsubishi pajero 1996 3.5 lt 24 valve dohc

ed904ac.gif
Here ya go....get the rest of the info right now.

Posted on Mar 26, 2009

emissionwiz
  • 75822 Answers

SOURCE: Timing Belt Tensioner bolt broken off.

if this happened you bent the valves in the engine and the cylinder head must be removed, here are full instructions for a timing belt replacement.

Required tools:
13mm open end wrench 10mm shallow and deep socket 8mm socket long flathead screwdriver 17mm deep socket T50 torx socket 1/4", 3/8ths and 1/2" ratchets and extensions E10 inverted torx sockets 6mm Allen wrench 15mm open end wrench 7mm socket 12mm open end wrench 14mm socket 12mm socket 8mm, 9mm and 10mm Allen head sockets 19mm socket pry bar needle nose pliers
If you are doing this because your timing belt broke you will also need to buy a complete cylinder head, head gasket set, and both idler pulleys. ALL DAEWOO MODELS WILL BREAK THE INTAKE AND EXHAUST VALVES WHEN THE TIMING BELT BREAKS.
Start by removing the air cleaner assembly from the throttle body, remove the air filter and housing jack up the vehicle and remove the wheel, remove the plastic shielding in front of the accessory drive belt assembly, remove the accessory drive belt, place a jack with a block of wood on top underneath the engine oil pan remove the front engine mount, remove the crank shaft pulley ( the 4 Allen head bolts only not the 17mm bolt in the center.) remove the metal plate behind the engine mount bracket on the engine, remove the plastic timing belt cover 3 clips on top 2 10mm bolts on bottom. Rotate the engine until the #1 cyl. is at Top Dead Center on the compression stroke or line up the crankshaft timing mark with the mark on the inner timing belt cover ( notch in cover with notch in pulley) on the camshaft pulleys -- ( intake cam line up the line on the pulley with the line on the inner cover)( exhaust cam line up the arrow on the pulley with the arrow on the inner cover) loosen the 13mm bolt in the belt tensioner and using the Allen wrench rotate the tab until there is slack in the belt. Remove the belt. At this time I would recommend you replace the water pump, both plastic idler pulleys as they tend to overheat and lockup, and the belt tensioner. Make sure all your marks are lined up, you may need a helper to hold the Exhaust Cam in place as it tends to move during belt installation. Put the timing belt underneath the crankshaft pulley, install the belt leaving the intake cam for last and NO BELT SLACK on the right side between the crank and the exhaust cam. Once the belt is installed rotate the crankshaft over 2 revolutions and make sure is rotates freely, and your timing marks are aligned perfectly if not the engine will not run properly, tension the belt as needed. Installation is the same as removal.

To clarify, on the DOHC engine, the intake cam gear has a line on it, and the exhaust cam gear has an arrow on it. These should be lined up with the corresponding line and arrow on the VALVE COVER, pointing straight up. I just went through this process over the weekend, and spent quite a bit of time looking for these marking as I had removed the valve cover. Once I found them, it was plain and simple.
In addition, be sure to not over tighten the belt when reinstalling. The tensioner has markings on it for "old" and "new". DO NOT adjust past "new", as the car will sound like a jet engine, and the belt will not last for very long.
One more item that you may as well replace while you are in there is the cam position sensor if you have not already, as there have been issues with them, and the timing housing has to be opened to get to it

Posted on May 26, 2009

blubanshee
  • 48 Answers

SOURCE: how do you take tension off vee belt for power

I think this will help you.

Click Here

Scroll down to pages 27 and 28 and I think you will find the information your looking for. It has a very good description and pictures of the belts and tensioner.

I hope this helps and have a great weekend.

Posted on Jun 07, 2009

co7196
  • 3433 Answers

SOURCE: power steering

oNE BOLT MISSING IS A PROBLEM IN ITSELF. And yes if you have a swepentine belt you must have a tebnsioner,. If it's a V belt then no the missing bolt is probably your adjustment point. Good luck

Posted on Jun 14, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to replace the power steering belt on a 4g13



ADJUSTMENT

Excessive belt tension will cause damage to the alternator and water pump pulley bearings, while, on the other hand, loose belt tension will produce slip and premature wear on the belt. Therefore, be sure to adjust the belt tension to the proper level.
To adjust the tension on a drive belt, loosen the adjusting bolt or fixing bolt locknut on the alternator, alternator bracket or tension pulley. Then move the alternator or turn the adjusting bolt to adjust belt tension. Once the desired value is reached, secure the bolt or locknut and recheck tension.


REMOVAL & INSTALLATION

1.5L, 1.6L, 1.8L, 2.0L and 2.4L Engines


0900c15280037bf7.jpg enlarge_icon.gifenlarge_tooltip.gif

Fig. Accessory V-belt routing-Mitsubishi 1.5L, 1.6L, 1.8L, 2.0L and 2.4L engines
Alternator Belt


0900c15280037bf8.jpg enlarge_icon.gifenlarge_tooltip.gif

Fig. Loosen the adjuster lock bolt . . .


0900c15280037bf9.jpg enlarge_icon.gifenlarge_tooltip.gif

Fig. . . . then remove the alternator belt from the engine

  1. Loosen the alternator support nut.
  2. Loosen the adjuster lock bolt.
  3. Rotate the adjuster bolt counter clockwise to release the tension on the belt.
  4. Remove the belt.

To install:
  1. Install the belt on the pulleys.
  2. Rotate the adjuster bolt clockwise until the proper tension is reached.
  3. Tighten the adjuster lock bolt and the alternator support nut.

POWER STEERING BELT


0900c15280037bfa.jpg enlarge_icon.gifenlarge_tooltip.gif

Fig. After the adjusting and fixed bolts are loosened, rotate the pump . . .


0900c15280037bfb.jpg enlarge_icon.gifenlarge_tooltip.gif

Fig. . . . then remove the power steering belt from the engine

  1. Remove the alternator belt as described above.
  2. Loosen the power steering pump adjusting bolts.
  3. Remove the power steering pump fixed bolt on the rear of the bracket.
  4. Rotate the pump toward the engine and remove the belt.

To install:
  1. Install the belt on the pulleys.
  2. Rotate the pump until the proper tension is reached.
  3. Tighten the adjusting bolts on the pump.
  4. Tighten the fixed bolt on the rear of the bracket.
  5. Install the alternator belt.

A/C COMPRESSOR BELT
  1. Loosen the tension pulley and remove the belt.
  2. The installation is the reverse of the removal.

3.0L DOHC, 3.0L SOHC Galant, and 3.5L Engines


0900c15280037bfc.jpg enlarge_icon.gifenlarge_tooltip.gif

Fig. Serpentine belt routing-Mitsubishi 3.0L engines (except 1998-00 Galant models)


0900c15280037bfd.jpg enlarge_icon.gifenlarge_tooltip.gif

Fig. Accessory V-belt routing-Mitsubishi 3.5L and 1998-00 3.0L SOHC Galant engines
ALTERNATOR AND A/C COMPRESSOR

  1. Disconnect the negative battery cable.


CAUTION Wait at least 90 seconds after the negative battery cable is disconnected to prevent possible deployment of the air bag.
  1. Raise and safely support the vehicle and remove the front undercover.
  2. Loosen the tension pulley fixing nut and relieve the tension on the belt by turning the adjusting bolt.
  3. Remove the belt.

To install:
  1. Install the belt on the crankshaft and alternator pulleys.
  2. Using the adjusting bolt on the tensioner, tighten the belt to the desired tension.
  3. Tighten the fixing nut to hold the adjustment.
  4. Install the undercover and lower the vehicle to the floor.
  5. Connect the negative battery cable.

POWER STEERING BELT
  1. Disconnect the negative battery cable.


CAUTION Wait at least 90 seconds after the negative battery cable is disconnected to prevent possible deployment of the air bag.
  1. Raise and safely support the vehicle and remove the undercover.
  2. Remove the alternator and A/C compressor belt.
  3. Lower the vehicle and remove the cruise control pump link assembly.
  4. Place the power steering hose under the oil reservoir.
  5. Loosen the tension pulley fixing bolts and remove the power steering pump drive belt.

To install:
  1. Install the power steering pump drive belt.
  2. Insert an extension bar or equivalent into the opening at the end of the tension pulley bracket and pivot the pulley to apply tension to the belt.
  3. Tighten the fixing bolts.
  4. Raise the vehicle and install the alternator and A/C compressor belt.
  5. Install the undercover and lower the vehicle.
  6. Connect the negative battery cable.

3.0L SOHC Diamante
  1. Disconnect the negative battery cable.
  2. Loosen the lockbolt on the face of the A/C tensioner pulley.
  3. Turn the adjusting bolt of the A/C tensioner pulley to loosen the tension of the A/C belt.
  4. Remove the A/C compressor belt.
  5. Loosen the locknut on the face of the power steering/alternator tensioner pulley.
  6. Turn the adjusting bolt of the tensioner pulley to loosen the tension of the belt.
  7. Remove the power steering/alternator belt.

To install:
  1. Install the power steering/alternator belt first and then the A/C compressor drive belt.
  2. Adjust the belts to the proper tension by turning the adjusting bolts and tighten pulley fixing nut/bolt.
  3. Tighten the mounting nut of the power steering/alternator tensioner pulley to 36 ft. lbs. (50 Nm).

Mar 21, 2013 | 1996 Mitsubishi Mirage

1 Answer

I am trying to change my 2001 Mitsubishi Mirage (w/ ac) alternator belt. I loosened the tensioner, took out the top - bottom and inside bolt of the ac compressor to take off the first belt and even took...


BEFORE ADJUSTING THE ALTERNATOR BELT DISCONNECT THE NEGATIVE BATTERY CABLE OR YOU MIGHT BLOW AN EXPENSIVE HIDDEN FUSE.
I would replace the steering pump belt at the same time you do the alternator belt (buy both).
To take off the alternator belt .
First , take off the negative battery cable so you do not blow an expensive fuse on the positive battery cable clamp(or a block fuse under the hood). Facing the back of the automobile , reach UNDER the alternator and loosen the bolt on the bottom right side, now loosen the bolt on the adjuster block on top, you can now turn the adjuster bolt and move the alternator to change the belt.
To take off the steering pump belt on the front of the motor, you need to loosen the nut on the back side of the pulley (right side of pump mount), the nut holds the adjuster pulley in place . With the adjuster pulley nut loose , you can use the adjuster bolt to move the pulley to adjust/take off the steering pump belt.

Jun 04, 2011 | 2001 Mitsubishi Mirage

1 Answer

I want to change two belts (A/C and Alternator) on my 1999 Mitsubishi Mirage 1.5 car. What steps I am suppose to do.


First, feel the tightness of your belts. You will have to tighten the new belts to the proper tightness. If they are too tight, they will wear the bearings prematurely. If they are too loose, they will slip.

Alternator Belt Removal

db56f56.gif


  1. Loosen the alternator lock nut.
  2. Loosen the adjuster bolt.
  3. Rotate the adjuster bolt counter clockwise to release the tension on the belt.
  4. Remove the belt.
Similarly for the compressor belt

98b2b36.gif
  1. Loosen the lock nut.
  2. Loosen the adjuster bolt.
  3. Rotate the adjuster bolt counter clockwise to release the tension on the belt.
  4. Remove the belt.
5. Install the new compressor belt

6. Rotate the adjuster bolt clockwise until the belt is tight like it was before you removed it.

7. Tighten the lock bolt.

8. Install the new alternator belt

9. Rotate the adjuster bolt clockwise until the belt is tight like it was before you removed it.

10. Tighten the lock bolt.

11. enjoy life

Oct 12, 2010 | 1999 Mitsubishi Mirage

2 Answers

I cant get the belt in front of my serpentine belt off


there is a tensioner that you will have to move likely with a pry bar. look for a pulley that does not appear to drive anything

Aug 16, 2010 | 1997 Mitsubishi Mirage

1 Answer

How do i change belt on mitubishi mirage 98


( BEFORE ADJUSTING THE ALTERNATOR BELT DISCONNECT THE NEGATIVE BATTERY CABLE OR YOU MIGHT BLOW AN EXPENSIVE HIDDEN FUSE)to change the alternator belt, you have to loosen the lower mount bolt on the alternator, loosen block shaped bolt that the long adjuster bolt goes through, and loosen the belt by turning the long adjuster bolt, take off the belt. to adjust the power steering belt, there is a long adjuster bolt that moves a tensioner pulley, first you have to loosen the nut that holds the pulley in place , now the pulley can be moved with the adjuster bolt.

May 24, 2010 | 1998 Mitsubishi Mirage

1 Answer

I need to replace the alternaor belt on my 2000 mitsubishi mirage 105ltr engine and i need a diagram please not a serpintine belt either


Click on the following: direct, free Link. It has the Belt Diagrams for your 2000 Mitsubishi Mirage with the unspecified 1.5L SOHC In-Line 4-Cylinder, but unspecified options (AC/No AC, Power Steering/NO Power Steering, etc).

Let me know if this helped, or if you have additional information or questions. Feel Free to contact me at FixYa.com!


http://www.2carpros.com/car_repair_information/year/2000/make/mitsubishi/model/mirage/2000_mitsubishi_mirage_drive_belt_routing_diagram.htm


May 18, 2010 | 2000 Mitsubishi Mirage

2 Answers

I need to replace the alternator belt on a 2000 mitsubishi mirage i would like a diagram please


If you have limited / no mechanical knowledge leave this to an Auto Technician.

This a relatively easy job.

Undo the alterantor lock nut (12mm ring spanner / socket wrench)
Undo the alternator adjustment bolt almost fully (Either 10mm / 12mm wrench)

Get under the car and loosen the main alterantor bolt using a 14mm wrench. Just loosen enough to move alternator, it is not to be removed.

Pull alterantor forward to slacken belt / remove belt.

Replacement is the opp of the above.

Ensure the MAX. deflection at the middle of the belt is only 12mm (1/2") after all redfitting is done.

Failure to have it this tight will wear it out very quickly!!

May 18, 2010 | 2000 Mitsubishi Mirage

1 Answer

How do i change the drive belt on a 97 Mirage


To change the drive belt you will need to find the tensioner pulley justt loosen the bolt /nut in the center of the pulley and then wind the pulley slider down usually located on the back side of the pulley. wind it down until you can slip the belt off. if the is 2 belt say for instance power steering and ac etc remove the outer belt first the power steering pump may have the tensioner on it same concept though. loosen nut/bolt and unwind til the belt slip off the pulley. remember to disconnect your battery because its better safe than sorry. Good luck!

Mar 08, 2010 | 1997 Mitsubishi Mirage

1 Answer

2000 Mitsubihi Mirage DE coup 1.5L -P.S. Belt


a225cad.gif
GENERATOR DRIVE BELT TENSION ADJUSTMENT/ PS

  1. Loosen the nut of the generator pivot bolt.
  2. Loosen the lock bolt.

Jun 05, 2009 | 2000 Mitsubishi Mirage

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

16 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

75822 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...