Question about 2001 Honda CR-V

1 Answer

Do u have to time the motor again when installing a distributor

I was driving in it just cut off and it wasnt firing now i put the distributor in it firing now but it want run

Posted by on

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

  • Contributor
  • 20 Answers

When you install a distributor on a honda engine, the camshaft has a slot cut in it which is not centered. The distibutor has teeth that are also off center so that it will only install IN PROPER TIMING. The car will (yes, it will) start, regardless of where the distributor is adjusted in the bolt slots.
Ensure that the ignition coil is installed properly and the wiring to the coil has the screws tightened all the way down.
Ensure that EVERY PLUG on the distributor has a wiring harness plugged in to it.
Firing order is 1,3,4,2. Number one post on the distributor is typically at the top and closest to the radiator. It turns clockwise. the next one around would be three, etc. The number one spark plug is the one all the way farthest to the driver side.

Post up your results. Thanks, and hooe this helps.

Posted on Jan 15, 2013

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

I'm working on a 99 blazer v6 4.3 L . It's out of time.I won't start how do I set the engine back on time and what's the sequence of such procedure?


Juan, you need to look for timing mark on crank shaft pully just below water pump,you will see a deep cut mark, turn over motor BY HAND disconnect battery,for safety , now remove # 1plug when you rotate motor you should feel compression , as piston comes up ,if you don't feel compression rotate motor 180 deg,as timing indecater alines with crankshaft timing mark, that should be (TDC) top dead center ,now set plug wires in firing order.make sure when starting that you have spark, if it wont start try resetting timing again, you may be 180 deg out . I hope this helped if it did let me know.
Woody

Sep 21, 2014 | 1999 Chevrolet Blazer

1 Answer

What best position timing mark fly wheel plate land criuser 3fe engine to re install distributor


If it rattles,timing is too far advanced.Loosen the distributor bolt,Back timing to fastest idle,and advance it just a little to where the idle is changing slower.Not much tho.Lock the distributor bolt and drive it.If still rattles,do it again till it doesn't rattle.The rattle you speak of is called engine nock,because it's firing ahead of time too much.

Apr 24, 2014 | 1990 Toyota Land Cruiser

1 Answer

Put a 1996 mustang v6 motor into a 1995 mustang that had a v6 now I can't get any fire


There should be a distributor module screwed to the side distributor, Make sure it did not get damaged or try putting the original one on the motor you just installed. There is special tool for the screws , It cost about $12.00 the d module itself cost about $60.00, I hope this helps and that it fixes your problem. Michael

Feb 13, 2013 | Cars & Trucks

1 Answer

97 f 250 5.8l cuts out under load


Cuts out when throttled in park or in gear if gear and cuts out cam can be blamed. Gas motor put a quart of tranny fluid in gas tank and run it it will clean valves

Jan 19, 2013 | 1997 Ford F250 SuperCab

1 Answer

My 1987 toyota wont fire all the time


did you change the igniter next to the coil ? you'll have to find a good used igniter they are expensive new or maybe ebay motors

Sep 04, 2012 | 1987 Toyota Pickup

1 Answer

Just wondering if you have a breakdown diagram for a 1992 dodge colt 1.5l distributer


I do not have a breakdown diagram for a distributor, but just the firing orders and description of ignition system for the Dodge Colt and related models (based on Chilton manuals) if that's what you're looking for: FIRING ORDERS Fig. 1: 1990 1.8L SOHC Engines Firing order: 1-3-4-2 Rotation: clockwise 84182009.gif

Fig. 2: 1.6L DOHC Engine Firing order: 1-3-4-2 Distributorless Ignition 84182010.gif

Fig. 3: 2.0L Engine Firing order: 1-3-4-2 Rotation: clockwise 84182011.gif

Fig. 4: 1.5L Engine Firing order: 1-3-4-2 Rotation: counterclockwise 84182012.gif

Fig. 5: 1993 1.8L Engine Firing order: 1-3-4-2 Rotation: counterclockwise 84182013.gif

Fig. 6: 2.4L Engine Firing order: 1-3-4-2 Rotation: clockwise 84182014.gif

To avoid confusion, replace spark plug wires one at a time. --- Distributor REMOVAL & INSTALLATION Although the distributor can be removed from the engine no matter which cylinder is about to fire, it is a good idea to have number one cylinder at TDC before distributor removal. 1.5L, 1.8L, 2.4L SOHC Engines
  1. Disconnect the negative battery cable.
  2. Disconnect and tag the spark plug wires from the distributor cap.
  3. Disconnect the distributor harness connector.
    Fig. 1: Ignition system for the 2.0L engine 84183001.gif

    Fig. 2: Ignition system for the 1.5L engine 84183002.gif

    Fig. 3: Ignition system for the 1992-93 1.8L engine 84183003.gif

    Fig. 4: Ignition system for the 2.4L engine 84183004.gif

  4. Loosen the distributor retaining bolt and remove the distributor from the engine. To install:
  5. Rotate the engine until No. 1 cylinder is at TDC on its compression stroke. NOTE: Be careful not to turn it to the No. 4 cylinder TDC on its compression stroke by mistake.
  6. Align the distributor housing and gear mating marks.
    Fig. 5: Ignition system for the 1990 1.8L engine 84183005.gif

    Fig. 6: Distributor installation for the 1990 1.8L engine 84183006.gif

    Fig. 7: Distributor installation for the 1992-93 1.8L engine 84183007.gif

  7. Install the distributor into the engine, while aligning the fine cut (groove or projection) on the distributor flange with the center of the distributor mounting stud.
  8. Install and tighten the distributor retaining bolt.
  9. Reconnect the distributor harness connector.
    Fig. 8: Distributor installation for the 2.4L engine 84183008.gif

    Fig. 9: Distributor installation for the 1.5L engine 84183009.gif

    Fig. 10: Distributor installation for the 2.0L engine 84183010.gif

  10. Install the distributor cap and spark plug wires.
  11. Reconnect the negative battery cable.
prev.gif next.gif prev.gif next.gif

Oct 11, 2010 | 1992 Dodge Colt

1 Answer

Need firing order for 94 gmc 350 pu diagram dist and wires if possible thanks


For GMC 350 the firing order is 1-8-4-3-6-5-7-2.

The distributor rotor turns clockwise when viewed from above, so the spark plug wires would be installed in the same order as the firing order, beginning with #1.

To find which contact in side the distributor cap that the rotor is "pointing" to, use a ratchet on the center bolt of the crankshaft and turn the engine over by hand (clockwise direction only as viewed from the front of the engine looking towards the firewall) until the timing mark on the harmonic balancer aligns with the "0" mark on the timing cover (may also be indicated by a deep "V" cut into the timing mark indicator attached to the timing cover).

Normally, the rotor will either be "pointing" towards the firewall with a bit more emphasis towards the driver's side cylinder bank, or it will be pointing towards the front of the passenger side front fender. If it is pointing towards the fender, turn the engine over again until the timing marks align and the rotor should be pointing towards the firewall as described above.

Find the closest terminal in the distributor cap that matches the rotor's alignment and install the #1 wire. The distributor cap and then be installed with the remaining wires installed around it clockwise from #1 using the firing order.

Some turning of the distributor may be necessary to get the engine statred. Once it does start, use a timing light to set the timing.

Hope helps (remember rated this).

Aug 02, 2010 | 1994 Chevrolet C1500

1 Answer

I dont know how to put my spark plug wires in my car


firing order 1-4-2-5-3-6

  1. Insert each ignition wire on proper terminal of distributor cap . Ensure ignition wires are properly seated on the terminals. The No. 1 terminal is identified on distributor cap .
not sure if #1 cylinder is on the front right or front left. Call a dealer.
d8a0dc7.gif
Installation
Before installing distributor , visually inspect distributor . Inspect the O-ring. It should fit tightly and be free of cuts. The drive gear should be free of nicks, cracks and excessive wear. Rotate distributor drive shaft. It should move freely, without binding.
  1. To install distributor correctly, No. 1 piston (6108) must be at Top Dead Center (TDC) of compression stroke. Remove No. 1 cylinder spark plug (12405) and rotate crankshaft (6303) clockwise until No. 1 piston is on the compression stroke.
  1. With No. 1 piston on compression stroke, align timing pointer with TDC on the crankshaft damper.
  1. Align locating boss on distributor rotor with hole on armature. Fully seat distributor rotor on distributor shaft.
  1. Rotate distributor shaft so blade on distributor rotor is pointing toward mark on distributor base that was previously made in Step 2 of the Removal procedure.
  1. While installing, continue rotating distributor rotor slightly so leading edge of the vane is centered in vane switch stator assembly.
  1. Rotate distributor in engine front cover to align leading edge of vane and vane switch stator assembly. Verify distributor rotor is pointing at No. 1 mark on distributor base. If vane and vane switch stator cannot be aligned by rotating distributor in engine front cover , remove distributor enough to just disengage distributor gear from camshaft gear. Rotate distributor rotor enough to engage distributor gear on another tooth of camshaft gear. Repeat Step 1 if necessary.
  1. Install distributor hold-down clamp and bolt. Tighten bolt, but leave it loose enough to rotate distributor .
  1. Install distributor cap , No. 1 spark plug and ignition wires. Check that ignition wires are securely connected to the distributor cap and spark plugs . Tighten distributor cap hold-down screws to 2.0-2.6 Nm (18-23 lb-in).
  1. Reconnect distributor to engine control sensor wiring .
  1. Set initial engine ignition timing according to procedures found in Section 8A of the Powertrain Control/Emissions Diagnosis Manual.
  1. After engine ignition timing is set, tighten distributor hold-down bolt on to 20-30 Nm (15-22 lb-ft).
  1. Recheck initial engine ignition timing. Adjust if necessary.

Apr 09, 2009 | 1993 Ford Thunderbird

1 Answer

I have 1993 nissain altima that is could cut off and is having a hard time getting it start back up while in the process of doing that it began to drain my battery and i have to jump it off. replaced the...


ijust had the same problem with my 93 it was the distributer itself.Once the new one was put on it fired right up/Make sure who ever does your work also cleans or replaces your plus they get fouled real quick from trying to start.

Jan 23, 2009 | 1994 Nissan Altima

Not finding what you are looking for?
2001 Honda CR-V Logo

54 people viewed this question

Ask a Question

Usually answered in minutes!

Top Honda Experts

yadayada
yadayada

Level 3 Expert

76109 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Kevin Daniels

Level 3 Expert

1455 Answers

Are you a Honda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...