Question about Cars & Trucks

Open Question

Replacing digidoor II rocker rail

How do I replace the rocker rail?

Posted by on

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

My digidoor 1000n motor recently did not close all the way leaving a gap of about 60 mm and yesterday the gap seemed a bit bigger more like 100 mm how do i set it to close fully


on the rail there should be 2 cylindrical black magnetic read switches with white wires connected to them.
Those are the open and close distance units
sometimes they come loose and move with the vibration of the motor when opening the door

Nov 30, 2016 | Cars & Trucks

1 Answer

Where can I get a digidoor 1 garage door motor ?


I found a site that you may check out go google -type in www.hydrodoors.co.za/products
they claim to be the home of digidoors. they have an e-mail , sales@digidoor.co.za and a telephone no. 0114749060
even if they are not close to you maybe you can purchase on line and have it sent to you.

Feb 17, 2015 | Cars & Trucks

1 Answer

2001 izuzu tropper 3000 wont start... Injectors replaced, 12V ok on the injectors, Can it be anything related with the oil pressure on the rail (injectors)?


oil viscosity is very important, and yes if the rail oil pressure sensor is not reading correctly at least 3 to 5 Mpa while cranking the injectors will not be turned on by the engine ecu. if you can get a scan tool look at rail oil pressure sensor reading just after cranking it should drop to 0 to 0.5 Mpa if any different its no good, also check for oil leaking out of main injector harness connector near engine oil dip stick if oil leaking out of connector this pressure switch which is in oil rail under rocker cover is no good and injector harness needs replacing this is very common.

Oct 02, 2013 | 1999 Isuzu Trooper

1 Answer

P 2647"A" Rocker Arm Actuator


Your going to need a air pressure regulator or better yet if the ECM found fault price it and replace it
  1. Start the engine, and let it run for 5 minutes, then turn the ignition switch to LOCK (0).
  2. Remove the cylinder head cover.
  3. Set the No. 1 piston at top dead center (TDC).
  4. Move the intake secondary rocker arm A for the No. 1 cylinder. The secondary rocker arm A should move independently of the secondary rocker arm B.
    1. If the intake secondary rocker arm A moves freely, go to step 5.
    2. If the intake secondary rocker arm A does not move, remove the secondary rocker arms as an assembly, then check that the pistons in the secondary rocker arms move smoothly. If any rocker arm needs replacing, replace the secondary rocker arms as an assembly, then retest.
    3. Repeat step 4 on the remaining intake secondary rocker arms with each piston at TDC. When all the secondary rocker arms pass the test, go to step 6.
    4. Check that the air pressure on the shop air compressor gauge indicates over 400 kPa (4.0 kgf/cm2, 57 psi).
    5. Inspect the valve clearance.
    6. Install a 10 x 1.0 mm adapter to the inspection hole, then connect the air pressure regulator
  5. With the specified air pressure applied, move the intake secondary rocker arm A for the No. 1 cylinder. The secondary rocker arm A and secondary rocker arm B should move together. If the intake secondary rocker arm A does not move, remove the secondary rocker arms as an assembly, and check that the pistons in the secondary rocker arms move smoothly. If any rocker arm needs replacing, replace the secondary rocker arms as an assembly, then retest.
  6. cansmo_32.gif
cansmo_33.gif

Aug 23, 2011 | Honda Accord Cars & Trucks

1 Answer

Replacing Hydraulic Lifters


YOU HAVE TO REMOVE VALVE COVERS LOOSEN REMOVE ROCKER ARMS ASSEMBLY KEEP ROCKER ARM ASSEMBLY IN ORDER SO THEY GO BACK IN THE ORIGINAL POSITION.YOU HAVE TO REMOVE INTAKE MANIFOLD ALSO.YOU NEED A REPAIR MANUAL FOR TORQUE SEQUENCE ON THE INTAKE MANIFOLD AND ROCKER ARMS TORQUE.

May 27, 2010 | 1994 Dodge Stealth

1 Answer

Oil leaks into sparkplug well


theres this seal that go on the rocker arms rail
you need to remove the rocker arm rail
if your very good mechanicly try it

May 08, 2010 | 1995 Honda Accord

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

256 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

76673 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...