Question about Cars & Trucks

Open Question

What is the problem when a mazda cronos 626 fails to start but cranks the engine(GT6K 00534)

Posted by Anonymous on

2 Suggested Answers

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.

Posted on Jan 02, 2017

  • 1 Answer

SOURCE: 91 mazda 626 erractic idle surge when engine is cold

My '91 626 did the same thing. I tested the throttle position sensor, and it was good so that wasn't it. The other likely culprit is the Idle Speed Control valve, or Idle Air Control valve, which is a $500 part new (more than I paid for the whole car). I pulled one off a 626 at the salvage yard and got it for 3 bucks, put it on (it's an easy DIY, just 4 philips screws holding it to the intake manifold), however I can't be sure that solved the problem, since I haven't run the car much since then. It would seem the most likely cause, tho, and a cheap fix if you go used. Other possibilities: O2 sensor or Mass Air Flow sensor?

Posted on Nov 28, 2009

Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

Does worn out rings cause a Mazda 626 Cronos V6 not to idle

It could but if its that bad you'd be burning a lot of oil and overheating. After changing all the filters and the PCV valve next would be to look into the EGR system. If your EGR hose is clogged it will cause revving and hesitation, uneven idle and often no check engine light. The other thing could be the camshaft position sensor needs replacing. Its typically in the distributor under the cap or hanging on the outside of the distributor. Usually the check engine light will come on if its the camshaft position sensor. Its worthwhile to check for engine codes even if your check engine light isn't on.

Jan 03, 2015 | Mazda Cars & Trucks

1 Answer

How do I achieve idling for a V6 Mazda 626 Cronos If you don't step on the gas it shuts off

Did you swap out throttle bodies? You may need to replace the PCM if you did. I don't think there's a way to rechip but then again maybe...

Jan 03, 2015 | 1999 Mazda 626

1 Answer

Mazda 626 v6 1992 model 2 liter.engine max rev 3500

cam sensor or crank failing. works fine till engine is hot. then cut out engine or just puts engine in limp mode. with engine ecu light on... dont know what the **** is .

Dec 02, 2013 | Cars & Trucks

1 Answer

99 Mazda 626 2.0 changed starter 3x's. No start

Well it could be an engine problem, or a bad connection with one of the battery cables. The engine would require more voltage to crank when it is hot, but not that much.
You might want to have someone check the engine to see how much drag is has when hot, by turning the crank by hand.

Jun 10, 2013 | Cars & Trucks

1 Answer

Failed inspection - mazda 626, year 2001

Your cig lighter is only supposed to operate when your key is in the on or acsessory position. Did the tester turn the key on,or start the car?

Aug 20, 2009 | 2000 Mazda 626

1 Answer

My new 94 mazda 626 2.0 is very hard starting

tap on the gas a couple of times then try to start it.

Apr 28, 2009 | 1994 Mazda 626

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

28 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts


Level 3 Expert

75807 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22133 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides