Question about Ford Taurus

1 Answer

How to get air out of cooling system on a 2000 ford taurus 3.0liter pushrod V6

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Ford Master
  • 5,278 Answers

With the radiator cap removed, starting the car and running it till normal operating temperature is reached will usually expel all the air from the system.

Posted on Jan 15, 2013

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

alicantecoli
  • 22114 Answers

SOURCE: 2000 ford taurus vacuum hose..

this vacumn line is to open the flaps on the A/C inside the car so it will run from the inlet manifold to somewhere on the heater/blower housing ,but where i cant help you with ,sorry none of these cars here in spain so i never seen one

Posted on Jul 17, 2009

  • 19 Answers

SOURCE: 2000 ford taurus.I can only get warm air to cool

a clogged heater core, a bad temp blend door actuator, or a damaged temp blend door

Posted on Dec 10, 2009

  • 85 Answers

SOURCE: Where is the camshaft position sensor on a 2000 Ford Explorer?

in the rear like where the dist would normaly be

Posted on Dec 31, 2009

ourhowse
  • 2007 Answers

SOURCE: 1999 Ford Taurus 3.0l EFI 6cyl, Heater does not

It could be air locked. Feel both your heater hoses, and, with the engine running, loosen the one that's cold, if there is one. If that doesn't help, it is probably your heat control valve that is malfunctioning.

Posted on Jan 08, 2010

  • 1 Answer

SOURCE: 1992 Ford Taurus with a 3.8l V6 the cooling fan

The Taurus has Two temp sensors. One for the dash, which is isolated, then one for the PCM, it also controls when the fan relay should actuate. Its a 2 wire sensor, just above the thermostat. If you remove the harness from that sensor, and the cooling fan comes on, at any temp, (should take 5- 10 seconds) then thats your fault.

Posted on Mar 11, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Where are the freeze plugs located on a 2000 ford taurus v6 3.0 liter


There are 6 on the block and 2 or more on each head. Getting the ones on the back of the heads are the tough ones.

Nov 19, 2014 | Ford Taurus Cars & Trucks

1 Answer

I have a 96 ford explorer v6 with a pushrod motor and after we replaced the pushrods, the head gaskets, the valve cover gaskets and the fuses, the car will not idle. what could be the problem?


Have you adjusted the pushrods properly? Pushrods generally need to be adjusted after installation.

Not sure how to do this on this model, although I own a 94 Ford Explorer with the V6 4.0 Liter motor.

Basically, when a gas engine doesn't run, you check 4 things, and narrow it down from there.

1. Gas (Is gas pressure good, is gas flow strong enough?)
2. Spark (are all spark plugs firing properly? Is spark strong enough)
3. Combustion at each cylinder (timing, pushrod adjustment)
4. Air Flow (MAF/MAP sensor working? Air Filter dirty?)

Appliance Repair Utah

Mar 25, 2012 | 1996 Ford Explorer

1 Answer

2000 Ford Taurus, V6, auto trans, new thermostat installed, still over heating, not sure if cooling fans are starting. Checked all fuses. Any ideas?


first i would check the cooling fan relays, when the temp gauge gets anywhere between over half and overheating you should hear the relays switch(it will make a clicking sound). but do not let the car overheat! Secondly the fans are controlled by the cooling fan temp switch/sender, this is located on the radiator, and you should check to see if the fan is getting power by using a volt-meter to check for the proper 12 volts. Finally if they still do not kick on you will need to replace the cooling fan motor(s).

May 18, 2010 | 2000 Ford Taurus

2 Answers

1992 Ford Taurus with a 3.8l V6 the cooling fan


The Taurus has Two temp sensors. One for the dash, which is isolated, then one for the PCM, it also controls when the fan relay should actuate. Its a 2 wire sensor, just above the thermostat. If you remove the harness from that sensor, and the cooling fan comes on, at any temp, (should take 5- 10 seconds) then thats your fault.

Sep 16, 2009 | 1992 Ford Taurus

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

54 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

75797 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

fordexpert

Level 3 Expert

5495 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...