Question about 1996 Jeep Grand Cherokee

1 Answer

I need 2 remove the front bumper on a 1997 jeep cherokee i have picked up a bull bar and was wanting to know the best way to go about it please thanks

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    President:

    An expert whose answer got voted for 500 times.

  • Master
  • 1,990 Answers

The Mounting Bolts are Inside the Frame Rail. They can be Tough sometimes. But, That is the Only way to get them out.

Posted on Jan 24, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to replace the electric fan on 2000 jeep grand cherokee


You must remove the entire front bumper and you will want to remove the radiator as well. There really isn't enough room there.

Remove headlights.
To remove the front bumper, there are plastic clips around wheel well and under the front bumper. Then there are a couple of bolts under the hood and two bolts on the side (look from wheel well up). The whole thing comes off as one piece.

I was able to move (twist) the A/C condensor out of the way and not drain it.

Jul 10, 2014 | 2000 Jeep Grand Cherokee

1 Answer

Remove front bumper 1999 tarago


Hi
This is how you remove the front bumpers from 1990-2000 model Toyota taragos/Previas
First if your tarago/previa has a bull bar it has to be removed, before you can remove the front bumper.

There are 6 X 18 mm bolts secured to the bull bar brackets, remove the 3 x 18mm on the left and 3 x 18mm on the left and place the bull bar in a secure area to reattach later, don't be surprised if its full of rust it needs to be sand blasted, rust treated and repainted.
The next step is to remove the bull bar brackets to do this you must remove the grille to access the 4 x 18mm bolts on the inside of the grille 2 x 18mm on the left and 2 x 18mm on the right.

Open the bonnet of your tarago/previa there is a screw at the top of the center of the grille that has to be removed and placed in a container to reassemble later.

The next step is a bit tricky but with persistence and practice you will get better, the grille has four plastic clips that hold the grill in place.


Now listen carefully, you cant just pull on the grille firmly and hope that strength alone will pop the grille, these clips are designed to open when the grille is pushed into place so the top and bottom of the clip have to be depressed to slide the insert out to remove the grille, but you can depress one side a time it dosent have to be both at the same time.


It just takes take and patience to do, start from the top left clip, pull the grille towards you and with a flat blade screw driver look down the grill and press the top of the clip still pulling the grille, the clip will depress but now you have to do the bottom of that clip too.


There are gaps in the grille you need a tool like a L shape pick or an interior tool shaped like a L for removing door trims, you can buy these items at $2 dollar shops, you feed the tool through the gap in the grille and place it under the bottom of the clip and when you press down it lifts up depressing the bottom of the clip while you are still pulling the grille towards you.


Once that clip is out stay on the left side and do the left bottom clip repeat the process and then do the right top clip and then the bottom right clip, when the grill is out push all the clips back into the grille so you don't loose them and place grille in a secure place until your ready to reassemble.


When you reassemble the grille you just place the grille over the insert holes and push them back into place they will automatically snap back into position and then screw the center top grill screw back in.


Now the grille is out, you will need an extension on your ratchet to reach and remove these bolts 4 X 18mm bolts, 2 on the left and 2 on the right, there is a dryer bottle on the left or right of your vehicle depending on country, so the extension needs to be reasonable long.


Once the brackets are removed place the bolts into your container, there are 4 x10mm bottom bumper bolts securing the bumper onto the reinforcement bar remove them.


Then there are 2 X 10mm upper corner bumper bolts securing the bumper to the body remove them, and then the last 2 X 10mm to be removed are at the bottom of the corner bumper secured on to a rail.


Once these 10mm bolts are removed the front bumper will slide off, place the bolts in your container and reassemble when ready.


Cheers



11_25_2012_11_59_18_pm.jpg

Jun 07, 2012 | Toyota Cars & Trucks

2 Answers

Cost of rear bumper, 97 jeep grand Cherokee.


Hi, The cost of the bumper is approximately $150, per the attached link: http://www.partstrain.com/ShopByDepartment/Bumper/jeep/grand_cherokee

Please remember tio rate this solution. Thank you!

Jan 12, 2011 | 1997 Jeep Grand Cherokee

2 Answers

2002 jeep grand cherokee larado is over heating. The cooling fanonly runs if I hotwire it. I changed th thermostat. Temp gauge is reading . Could it be the cooling fan relay if so where is it located. The...


Fan relay is located under pass headlight. Remove light assembly, use 2 1/2 " hole saw to drill hole in plastic housing ,3"from back wall, 3'' from left side.This will put you right over relay. Unscrew two bolts,replace. Relay was $40.... dealer wanted$350 to remove front bumper to replace it.

Sep 02, 2010 | 2002 Jeep Grand Cherokee

1 Answer

2006 jeep grand cherokee bumper removal


check your metal bumper retainers attached to the front chassis there must be a hidden bolts and nuts thats still on that you havent seen yet remove it and take off the bumper bar( steel bumper)

Apr 07, 2010 | 2006 Jeep Grand Cherokee

1 Answer

Where is the horn located on a1997 grand cherokee


The horn on the 1997 Jeep is located on the steering wheel.

The actual sound part (horn) is located under the front right side of the front bumper. If you stand in front of the jeep and stick your hand in the left most cutout hole on the bottom of the plastic bumper cover, you can touch the dual horns as well as remove them and replace them.

4560d45.png

I really hope help with this. Remember rated and comment this post.

Mar 10, 2010 | 1997 Jeep Grand Cherokee

1 Answer

How to fit it. bull bar


the main fixing bolt holes are usually below the front bumper, at the sump guardand behind the front grille for the secondary holes

Jul 28, 2009 | 2002 Land Rover Range Rover

1 Answer

Romoving front Tow Bar...


Just have to remove the 3 bolts on each side of the bumper. Just move the rubber splash guards out of the way so you can see the bolts up under there. Make sure you use anti-seize compound on the bolts when you reinstall. You will probably have to adjust each side of the bumper bracket so it fits back on your Jeep, cause with the tow bar removed, there is a gap now.

Apr 08, 2009 | 1995 Jeep Cherokee

1 Answer

I have a 1997 cherokee country 6 cyl. 4.0L, and my cruise control will not work I dont know what it is?


Cruise control works from engine vacuum. Check for leaks where vacuum hoses connect to inlet manifold and vacuum canister behind front bumper for damage or leaks.

Feb 14, 2009 | 1997 Jeep Cherokee Country

2 Answers

1996 grand cherokee bumper


there is a trim panel on top of rear bumper if you look underneath there are clips that go through metal bumper also there are 4 plastic fasteners that will need to be replaced after removing best to get clips at dealer cheap enough hope this helps ya

Jul 07, 2008 | 1996 Jeep Grand Cherokee

Not finding what you are looking for?
1996 Jeep Grand Cherokee Logo

Related Topics:

95 people viewed this question

Ask a Question

Usually answered in minutes!

Top Jeep Experts

yadayada
yadayada

Level 3 Expert

70387 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22041 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6880 Answers

Are you a Jeep Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...