Question about Cars & Trucks

Open Question

I have an 04 Nissan 350z and just changed my spark plugs. I disconnected the fuel line and some of the wiring harness to get to the plugs. After putting it all back together and starting my car the tcl & slip light/ check engine light stay on. The car sputters and stalls. I checked all of the wire connections and tried to bleed any air from the fuel line. What should I do?

Posted by Anonymous on

Ad

5 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
cadman000
  • 607 Answers

SOURCE: 1990 Buick Century 3.3L Check Engine Light comes on, stalls.

Need to check for fault codes. Possibly a faulty sensor causing the fuel system to run rich or lean.

Posted on Mar 27, 2009

Ad
dttech
  • 4803 Answers

SOURCE: while driving the abs light comes on then goes out

The only way that the ABS light could have anything to do with your stalling problem is if it is caused by a bad battery ground, Otherwise, I would begin diagnosis by collecting fault codes from both the ABS module and the Engine Control Module.

Posted on Nov 09, 2009

  • 5 Answers

SOURCE: 2003 Kia Sedona won't start

\I WAS HAVING THE SAME PROBLEM, IF THE CHECK ENGINE LIGHT DOES NOT COME ON, IT COULD BE A CLOGGED CATALETIC CONVERTER, THE EASIEST WAY TO TEST THIS ,TO ME ANYWAY, IS TO DISCONNECT THE EXHAUST PIPES(COMING OFF THE ENGINE) AND THE CONNECTION TO THE FRONT OF THE CATALETIC CONVERTER, THEN START THE CAR AND SEE WHAT IT DOES, IF THE ENGINE SURGE GOES AWAY(REMEMBER THE CAR WILL BE LOUD) BUT YOU ARE LOOKING FOR THE ENGINE HEALTH TO GO TO NORMAL, IF IT DOES YOUR CAT IS CLOGGED

Posted on Jan 11, 2010

  • 1 Answer

SOURCE: my nissan 350z sometimes stalls after starting

after i replaced the battery in my 2003 350z, it would stall immediatly after i cranked it on unless i gave it a little gas. I fixed this by cleaning the MAF and throtle body valve. Total supply costs were $15 and took about 20 minutes. My Z is not only fixed but runs smoother and cleaner.

Posted on Feb 27, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to fix a car that cranks but won't start. No spark. No fault codes. No engine light. Good battery. It's not a fuel problem. Ignition harness is good.


send it back and try another computer, they do sell junk ones, i hope thats it, anything done to it b4 this started? stereo stuff, wiring?

Mar 16, 2015 | 2004 Nissan 350Z

1 Answer

Spark plugs


Check this SPARK PLUG REPLACEMENT - REMOVAL PROCEDURE

1_23_2012_5_10_32_pm.jpg

1. Remove the ignition coils (lines at end this document), then return here once you have gotten the Coil
Packs off and precede with step 2 from here.
2. Clean the spark plug recesses with low pressure air. CAUTION: Wear safety glasses
when using compressed air, as flying dirt particles may cause eye injury. NOTE:
Clean the spark plug recess area before removing the spark plug. Failure to do so could
result in engine damage because of dirt or foreign material entering the cylinder head, or
by the contamination of the cylinder head threads. The contaminated threads may prevent
the proper seating of the new plug. Use a thread chaser to clean the threads of any
contamination.
3. Remove the spark plugs from the cylinder head. NOTE: Allow the engine to cool before
removing the spark plugs. Attempting to remove the spark plugs from a hot engine may
cause the plug threads to seize, causing damage to cylinder head threads.
4. Inspect the spark plugs.

INSTALLATION PROCEDURE

1_23_2012_5_11_30_pm.jpg

1. Measure the spark plug gap on the spark plugs to be installed. Compare the measurement
to the gap specifications. NOTE:
• Use only the spark plugs specified for use in the vehicle. Do not install spark
plugs that are either hotter or colder than those specified for the vehicle. Installing
spark plugs of another type can severely damage the engine.
• Check the gap of all new and reconditioned spark plugs before installation. The
pre-set gaps may have changed during handling. Use a round feeler gage to ensure
an accurate check. Installing the spark plugs with the wrong gap can cause poor
engine performance and may even damage the engine.
2. Install the spark plugs to the cylinder head. NOTE:
• Be sure that the spark plug threads smoothly into the cylinder head and the spark
plug is fully seated. Use a thread chaser, if necessary, to clean threads in the
cylinder head. Cross-threading or failing to fully seat the spark plug can cause
overheating of the plug, exhaust blow-by, or thread damage.
• Refer to Component Fastener Tightening Notice in Service Precautions.
Tighten the spark plugs to 18 N.m (13 lb ft).
3. Install the ignition coils.

IGNITION COIL(S) REPLACEMENT
REMOVAL PROCEDURE
1. Remove the air cleaner resonator and outlet duct.
2. Disconnect the engine wiring harness electrical connector (1) from the oil pressure sensor (2).
3. Disconnect the engine wiring harness retainers (1) from the power steering pump (2).
4. Disconnect the engine wiring harness electrical connectors (1, 4) from the following:
• The exhaust camshaft position (CMP) sensor (5)
• The camshaft position (CMP) actuator solenoid valve (6)
5. Disconnect the engine wiring harness retainer (2) from the camshaft cover (3).
6. Disconnect the engine wiring harness electrical connectors from the following:
• The engine coolant temperature (ECT) sensor (1)
• The fuel injector harness (2)
• The ignition coils (4)
• The heated oxygen sensor (HO2S) (5)
7. Disconnect the engine wiring harness electrical connector from the intake camshaft position (CMP) sensor.
8. Carefully disengage the engine wiring harness conduit from the camshaft cover, and position aside.
9. Remove the ignition coil bolts.
10. Remove the ignition coils from the camshaft cover.

INSTALLATION PROCEDURE
1. Install the ignition coils into the camshaft cover. IMPORTANT: Ensure the ignition coil seals are properly seated to the camshaft cover.
2. Install the ignition coil bolts. NOTE: Refer to Fastener Notice in Service Precautions. Tighten the ignition coil bolts to 10 N.m (89 lb in).
3. Attach the engine wiring harness conduit to the camshaft cover.
4. Connect the engine wiring harness electrical connector to the intake CMP sensor.
5. Connect the engine wiring harness electrical connectors to the following:
• The ECT sensor (1)
• The fuel injector harness (2)
• The ignition coils (4)
• The HO2S (5)
6. Connect the engine wiring harness electrical connectors (1, 4) to the following:
• The exhaust CMP sensor (5)
• The CMP actuator solenoid valve (6)
7. Connect the engine wiring harness retainer (2) to the camshaft cover (3).
8. Connect the engine wiring harness retainers (1) to the power steering pump (2).
9. Connect the engine wiring harness electrical connector (1) to the oil pressure sensor (2).
10. Install the air cleaner resonator and outlet duct.

Hope this helps; also keep in mind that your feedback is important and I`ll appreciate your time and consideration if you leave some testimonial comment about this answer.

Thank you for using FixYa, have a nice day.

Jan 23, 2012 | Cars & Trucks

1 Answer

How to change spark plugs in a 2005 chev colorado


SPARK PLUG REPLACEMENT - REMOVAL PROCEDURE

1_23_2012_5_10_32_pm.jpg

1. Remove the ignition coils (lines at end this document), then return here once you have gotten the Coil
Packs off and precede with step 2 from here.
2. Clean the spark plug recesses with low pressure air. CAUTION: Wear safety glasses
when using compressed air, as flying dirt particles may cause eye injury. NOTE:
Clean the spark plug recess area before removing the spark plug. Failure to do so could
result in engine damage because of dirt or foreign material entering the cylinder head, or
by the contamination of the cylinder head threads. The contaminated threads may prevent
the proper seating of the new plug. Use a thread chaser to clean the threads of any
contamination.
3. Remove the spark plugs from the cylinder head. NOTE: Allow the engine to cool before
removing the spark plugs. Attempting to remove the spark plugs from a hot engine may
cause the plug threads to seize, causing damage to cylinder head threads.
4. Inspect the spark plugs.

INSTALLATION PROCEDURE

1_23_2012_5_11_30_pm.jpg

1. Measure the spark plug gap on the spark plugs to be installed. Compare the measurement
to the gap specifications. NOTE:
• Use only the spark plugs specified for use in the vehicle. Do not install spark
plugs that are either hotter or colder than those specified for the vehicle. Installing
spark plugs of another type can severely damage the engine.
• Check the gap of all new and reconditioned spark plugs before installation. The
pre-set gaps may have changed during handling. Use a round feeler gage to ensure
an accurate check. Installing the spark plugs with the wrong gap can cause poor
engine performance and may even damage the engine.
2. Install the spark plugs to the cylinder head. NOTE:
• Be sure that the spark plug threads smoothly into the cylinder head and the spark
plug is fully seated. Use a thread chaser, if necessary, to clean threads in the
cylinder head. Cross-threading or failing to fully seat the spark plug can cause
overheating of the plug, exhaust blow-by, or thread damage.
• Refer to Component Fastener Tightening Notice in Service Precautions.
Tighten the spark plugs to 18 N.m (13 lb ft).
3. Install the ignition coils.

IGNITION COIL(S) REPLACEMENT
REMOVAL PROCEDURE
1. Remove the air cleaner resonator and outlet duct.
2. Disconnect the engine wiring harness electrical connector (1) from the oil pressure sensor (2).
3. Disconnect the engine wiring harness retainers (1) from the power steering pump (2).
4. Disconnect the engine wiring harness electrical connectors (1, 4) from the following:
• The exhaust camshaft position (CMP) sensor (5)
• The camshaft position (CMP) actuator solenoid valve (6)
5. Disconnect the engine wiring harness retainer (2) from the camshaft cover (3).
6. Disconnect the engine wiring harness electrical connectors from the following:
• The engine coolant temperature (ECT) sensor (1)
• The fuel injector harness (2)
• The ignition coils (4)
• The heated oxygen sensor (HO2S) (5)
7. Disconnect the engine wiring harness electrical connector from the intake camshaft position (CMP) sensor.
8. Carefully disengage the engine wiring harness conduit from the camshaft cover, and position aside.
9. Remove the ignition coil bolts.
10. Remove the ignition coils from the camshaft cover.

INSTALLATION PROCEDURE
1. Install the ignition coils into the camshaft cover. IMPORTANT: Ensure the ignition coil seals are properly seated to the camshaft cover.
2. Install the ignition coil bolts. NOTE: Refer to Fastener Notice in Service Precautions. Tighten the ignition coil bolts to 10 N.m (89 lb in).
3. Attach the engine wiring harness conduit to the camshaft cover.
4. Connect the engine wiring harness electrical connector to the intake CMP sensor.
5. Connect the engine wiring harness electrical connectors to the following:
• The ECT sensor (1)
• The fuel injector harness (2)
• The ignition coils (4)
• The HO2S (5)
6. Connect the engine wiring harness electrical connectors (1, 4) to the following:
• The exhaust CMP sensor (5)
• The CMP actuator solenoid valve (6)
7. Connect the engine wiring harness retainer (2) to the camshaft cover (3).
8. Connect the engine wiring harness retainers (1) to the power steering pump (2).
9. Connect the engine wiring harness electrical connector (1) to the oil pressure sensor (2).
10. Install the air cleaner resonator and outlet duct.

Hope this helps; also keep in mind that your feedback is important and I`ll appreciate your time and consideration if you leave some testimonial comment about this answer.

Thank you for using FixYa, have a nice day.

Jan 23, 2012 | Cars & Trucks

1 Answer

U1000


U1000 - CAN Communication Line Signal Malfunction

Causes:
- Harness or connectors (CAN communication line is open or shorted)
- Faulty Engine Control Module (ECM)

Solutions:
- Poor harness ground connection

There is a service bulletin for the following Nissan models with U1000 code:

2002-2006 Nissan Maxima
2004-2006 Nissan Titan
2004-2006 Nissan Armada
2002-2006 Nissan Sentra
2005-2006 Nissan Frontier
2002-2006 Nissan Altima
2005-2006 Nissan Xterra
2005-2006 Nissan Pathfinder
2004-2006 Nissan Quest
2003-2006 Nissan 350Z
2003-2006 Nissan Murano

The service bulletin suggest cleaning engine and body harness ground connection to repair problem.

Feb 14, 2011 | Nissan Versa Cars & Trucks

1 Answer

What parts would i need for tuning up my sentra 04 (specific)


Your car has a coil on plug ignition system. So, you would replace the spark plugs, air filter, cabin air filter and PCV Valve. There are no spark plug wires, distributor cap or rotor and the fuel filter is in the tank, not requiring replacement for the life of the vehicle.

Dec 06, 2009 | 2004 Nissan Sentra

2 Answers

My nissan 350z sometimes stalls after starting


after i replaced the battery in my 2003 350z, it would stall immediatly after i cranked it on unless i gave it a little gas. I fixed this by cleaning the MAF and throtle body valve. Total supply costs were $15 and took about 20 minutes. My Z is not only fixed but runs smoother and cleaner.

Jul 11, 2009 | 2003 Nissan 350Z

2 Answers

04 nissan sentra engine stalls after 30 sec and ck engine lt comes on. Replaced fuel pump and ckd fuses under dash but its not pumping fueld thru the line.


Hello;
What are the codes from the DTC? That will help to pin point where the problem lies. The fuel filter could also be heavily plugged.
Thanks;
Rich
RPM Northwest

Jul 02, 2009 | 2004 Nissan 350Z

1 Answer

Diagram for 04 nissan 350Z roadster


one under the hood and one at the drivers kick panel

Mar 29, 2009 | 2004 Nissan 350Z

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

22 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

76673 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...