Question about 2001 Chrysler Sebring

1 Answer

Obd2 cod 1751

My car doesnt move when shift from P to D or R

Posted by on


1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points


    An expert that got 20 achievements.


    An expert that got 10 achievements.


    An expert that got 5 achievements.

  • Master
  • 1,498 Answers

Hi Saya,

I don't know if you were able to see my response on your other post. This is in case you didn't.

Were there any warning signs before it completely quit?
Any other symptoms?

When trying to diagnose problems remotely, the more detail the better.

In the meantime,

  • Check the fluid level. Low levels can cause the symptoms you describe.
  • Then re-check the diagnostic codes for changes.
If the solenoid code remains, the solution requires the opening of the transmission and a significant expertise in transmission repair.

Without the specific training, even skilled mechanics consider repair on automatic transmissions to be one of the 'Black Arts' and will refer the job to a pro. I have to give you the same advice.

The good news is, of all the things that can go wrong, the cost of this item is on the low end of the scale.


Posted on Jan 24, 2009


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

a 6ya Mechanic can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repair professionals here in the US.
click here to Talk to a Mechanic (only for users in the US for now) and get all the help you need.

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

I have a trouble code p1751, what that suppose to be?

no make ,model , year mentioned ( essential information for close answers)
code p 1751 refers to AT-shift solenoid 1--open circuit ===causes wiring ---shift solenoid
if you have an automatic and there are shifting problems check it out --replace shift solenoid 1

Jul 28, 2016 | Cars & Trucks

1 Answer

Po700 and po976 cod what are these cods

tranny codes if its not shifting get a good used tranny

Feb 21, 2015 | 2010 Chevrolet Cobalt

1 Answer

Will not shift into gear

the shifter lever dont move
or the car dont move.
lots of parts HANDS to tires.
how about reverse.?

car wont move, i guess.
check all fuse first.
then check ATF levels, not guessing, use the operators guide instructions to the letter !
if that checks out. then SCAN it,
connect any SCAN tool to the OBD2 16pin connector at dash
and SCAN it.
bingo for DTC tranny codes, P07xx? or ??????????????
that is a start.

Jul 05, 2014 | 2005 Buick Rendezvous CX

1 Answer

Why doesnt my nissan altima shift

Im assuming you mean that the vehicle wont move when put it in gear and its an automatic! Check the transmission fluid level if it is ok check if vehicle will move in any other gear reverse 1 or L etc. If not it maybe a torque converter issue and maybe best for a transmission shop to sort

Apr 14, 2014 | 2005 Nissan Altima

1 Answer


p0501=speed sensor fault.Check sensors on wheel hubs.

Apr 10, 2014 | 1995 Saab 900

1 Answer

Trans stuck in limp mode i'm getting a p1751 code

P 1751 Shift Solenoid" A" performance. The solenoid is part of the transmission valve body and yes if this solenoid fails you will get limp mode.The only solution is a new solenoid may be even the wires to it or even the transmission module

Feb 26, 2012 | Cars & Trucks

2 Answers

I scanned and get codes 1751 pd and 1751 trans will not shift 2001 diamante

P1751 A/T Control Relay>>>Check power circuit to automatic trans (A/T) control relay, AND RELAY ITSELF FOR PROPER OPERATION!!

Oct 10, 2010 | 2001 Mitsubishi Diamante

1 Answer

Transmission wont shift into any gear

if you can shift gears with car off might be the clutch or slave cylinder. If you can start the car in gear,clutch pushed in and doesnt try take off probally not slave cylinder. But if it tries to take off,slave cylinder. Now if it doesnt try to take off,ease clutch out. Does it move or just rev up? If it revs up likely the tranny. But if it moves can you shift thru all gears,if so clutch is shot.

Feb 27, 2010 | 1995 Toyota Camry

1 Answer

92 yj front axle

it actually moves a shift fork onto a spline. try moving fork by hand.

Aug 05, 2008 | 2004 Jeep Wrangler

Not finding what you are looking for?
2001 Chrysler Sebring Logo

114 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chrysler Experts


Level 3 Expert

77194 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22265 Answers


Level 3 Expert

814 Answers

Are you a Chrysler Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides