Question about Cars & Trucks

Open Question

Where is turn signal flasher relay on 2004 chevy tahoe

Left signal flasher stops after 10 to 15 seconds. right signal and hazard flasher works fine

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get to try the service completely Free afterwhich it costs $6 per call and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 1 Answer

SOURCE: turn signals

replaced turn signal flashers and muti switch turn signal still won't work Why?

Posted on Nov 11, 2008

Ad
  • 272 Answers

SOURCE: 1997 sonoma turn signal flasher

The flashers are located behind the instrument panel trim, roughly between the base of the steering wheel and the ashtray, just to the left of the car lighter. To access the flashers, you need to at least loosen the lower instrument panel trim. Just under the steering column there are two screws with star heads. One to the left of the column and one to the right. You need to remove both of these screws. You will need to remove your ashtray. On the upper left corner of the hole left by removing the ashtray is a 9/32 hex head screw. You need to remove it. Once these three screws are removed you should be able to pull down on this portion of trim under your instrument cluster. When you do this it may cause trim around your instrument cluster to loosen that you can just pop back into place with your hand. You won't need to pull down to far on this trim piece as there are still some screws holding the bottom. You should be able to pull it down far enough to see the flasher units behind and just to the left of the cigarette lighter. There are two flasher units and I found that the one on the right is for the turn signals.On the left the other is for the hazard flashers. It may be a hand scraping experience to replace the flasher but it beats paying someone to do it for you. They are easy to recognize because the are silver and round metallic plug ins. The flasher unit on the left is for the emergency flashers and the one on the right is for turn signals. You can place the emergency flasher unit into the slot the turn signal unit belongs until you get a replacement. These flasher units are pretty cheap.

Posted on Jun 02, 2009

  • 4 Answers

SOURCE: 99 Chevy Tahoe... Rear turn signals, brake lights, and hazards

I had this problem, and to be honest, it happened to the left side about a week later...it's the board that the bulbs plug into...it's a very common problem with this model. So popular that you can normally get the socket board off the shelf at a parts store! it's extremely simple to replace, and I replaced all the bulbs at the same time!

Posted on Oct 11, 2009

  • 1 Answer

SOURCE: turn signals hazards flasher don't work jeep

I NEED TO LOCATE THE SWITCH WHERE IS IT ?
MY INDICATORS NOR HAZARD LIGHTS ARE WORKING I DONT KNOW WHAT IS WRONG WITH IT CHANGED BULBS BUT NOTHIGN THEY ALL WENT OUT AT THE SAME TIME
SO THERE MUST BE A RELAY SWITCH SOMEWHER BUT DONT KNOW WHERE ?
THANKS FOR HELPING

Posted on Apr 01, 2010

flbergeron68
  • 541 Answers

SOURCE: where is the turn signal flasher/relay for 2004

under the dashboard

Posted on Jul 04, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2004 chevy blazer . Problem is the horn does not work and turn signal flashes fast on both sides.


Do you know how to do automotive electrical testing ? Do you know what a relay is and how it works ? Turn signals flashing fast , could be aburnt bulb , flasher module .
VEHICLE RELAYS Operation Diagnosis
Turn Signal Lamps
The HAZ LP fuse in the underhood fuse block supplies battery positive voltage to the multifunction hazard switch assembly. The TURN fuse in the IP fuse block supplies Ignition positive voltage to the multifunction turn signal switch assembly. With the ignition switch in the RUN or START position, ignition positive voltage is connected through the multifunction turn signal and hazard switch assembly to the flasher module which is grounded at G205. When the turn signal switch is placed in either the left or right position, the circuit is complete from the flasher module to the turn signal lamps and to ground. The flasher module then sends an on-off voltage signal to either the left or right turn signals and their instrument panel cluster (IPC) indicator. When the hazard switch is activated, all turn signal lamps will flash including both IPC turn indicators. The front turn signals are grounded at G111 and G112. The rear turn signals are grounded at G475 and G422 on the pickup and G450 on the utility.

Aug 26, 2017 | Cars & Trucks

1 Answer

How do you locate and test flasher relay on a 2006 Chevy Equinox? Turn signals and hazards stopped working after changing audio system. Fuses test good. Thank you, Mike


Did you change any wiring , tap into any wiring ? There is no flasher relay on your vehicle . It controlled by the BCM !
Turn Signal/Hazard Lamps
The body control module (BCM) is responsible for controlling the turn signals and hazard lamps. When the turn signal switch is placed in either the left turn or right turn position, the BCM receives a signal from the turn signal switch. The BCM then sends an on-off voltage signal to either the left or right turn signals and their instrument panel cluster (IPC) indicator. When the hazard switch is pressed, the BCM receives a signal from the hazard switch. The BCM then will send an on-off voltage signal to all the turn signal lamps. All the turn signal lamps will flash including both IPC turn signal indicators.
Your best bet , take it to a qualified repair ! We on here have no clue what you did . On this newer vehicles ,if you know nothing about automotive electronics you really should take to a professional

Aug 10, 2017 | Cars & Trucks

1 Answer

I have a 1992 chevy c1500 with light issues. Left turn signal works fine, right side blinks like 4 ways,along with license plate light.when head lights are on nothing for right side turn signals. Hazards...


It seems to be a ground defect on right side. Do you have the same bulb's number . What about the front flasher. remove right rear lamp assembly remove connector measure voltage between ground and current .reconnect it measure voltage at bulb socket. you should find your problems
hope it helps

Dec 07, 2014 | 1992 Chevrolet C1500

1 Answer

'88 Chevy S10 pickup with flashers working only on driver side. Hazards work fine so I was told to replace the flasher relay. Does that sound reasonable and if so where is the relay located? If not,...


logically NO. if flashers work on one side, doesn't that tell you its OK? the flasher doesn't know left or right. what do you mean be "not working"? I would suspect the turn signal switch.

Sep 16, 2011 | Chevrolet S 10 Cars & Trucks

3 Answers

I have a 2004 Monte Carlo, my turn signals and flashers just stopped working, the fuse is good and all the bulbs are good. Does anyone have any other ideas as to what is causing this problem.


The turn signal switch assembly often causes this problem. If the hazard button is on your steering column it is part of the switch assembly and is called a multi-function switch . If it has a separate hazard button on the dash the can also cause the the same thing to happen. Try holding very slight pressure on the hazard button on the dash while the turn signal is on. If it starts working correctly replace only the the hazard switch. It is usually just snapped into the hole in the dash. If the hazard switch is on the column, than you should replace the multi-function switch. If it is equipped with an airbag, be sure the key is off while working on column. The multi-function switch should not require removal of the steering wheel on this car.

Jan 07, 2011 | 2004 Chevrolet Monte Carlo

1 Answer

1997 Chevy Tahoe both turn signals stopped working


Sounds like the flasher unit to me. Normally the emergency flasher and turn signal are separate.

Jul 21, 2009 | 2001 Chevrolet Tahoe

1 Answer

Turn signal does not flash right or left. Where is flasher unit?


yes it is the same. the problem is most likely the turn signal switch which is located on the steering column. be sure to check all fuses, relays, and bulbs first. keep me posted thanks

Jan 31, 2009 | 1996 Chevrolet S-10 Pickup

1 Answer

2004 F150- Hazard Flashers dont work, turn signals do work


try replacing the hazard relay it should be under the dash try turning it on and off with your head down by the floorboard to pinpoint the right relay and the location. you should be able to hear it easily. hope this helps.

Dec 04, 2008 | 2004 Ford F150

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

215 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

76630 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...