Question about Ford Fusion

Open Question

How to replace pcv valve on a 2007 ford fusion 2.3 l engine

Posted by Anonymous on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Handy Mike
  • 6 Answers

SOURCE: how do i replace the pcv valve on a 2000 explorer xlt v6 sohc?

On the passenger side of the intake manifold, coming off the bottom about the center of the engine front to back, you'll feel a hose that comes off a nipple. That hose makes a 90 degree bend and goes around to the rear of the motor. Where that hose meets the Y-connector from the other side of the intake you'll find the PCV valve. It's almost impossible to see it with the hood installed, and even tougher to reach it.

A good source of information for Ford Explorers can be found here

Posted on Oct 25, 2008

  • 3 Answers

SOURCE: PCV valve location

if i know what you are asking, look at where you put your oil in. on the valve cover to the top right should be a plug with a tubeing runs to your air clear tube where the air mass sensor and carb is located. i think that is what you are looking for.

Posted on Nov 07, 2008

warlock61
  • 659 Answers

SOURCE: No transmission fluid Dipstick on my 2007 Ford Fusion

depending on which trans it is there is a small dipstick on the trans at the front on the bottom these transmissions take a specific fluid so be careful

Posted on Nov 22, 2008

davesmith_37
  • 94 Answers

SOURCE: where is the pcv valve located on a 2003 ford ranger

  • The PCV valve can be located in several places. The most common location is in a rubber grommet in the valve cover. It can be installed in the middle of the hose connections, as well as installed directly in the intake manifold.
  • Once the PCV valve is located, make sure all the PCV system hoses are properly connected and that they have no breaks or cracks.
  • Remove the air cleaner and inspect the air and crankcase filters. Crankcase blowby can clog these with oil. Clean or replace such filters.
  • Oil in the air cleaner assembly indicates that the PCV valve or hoses are plugged.
  • Make sure you check these and replace the valve and clean the hoses and air cleaner assembly.
  • When the PCV valve and hose are in satisfactory condition and there is oil in the air cleaner assembly, perform a cylinder compression test to check for worn cylinders and piston rings.
  • Posted on Feb 27, 2009

    • 1 Answer

    SOURCE: 2003 FORD EXPEDITION PCV VALVE LOCATION

    show me a picture. everyone else says it's on the passenger side. nothing white on driver side of my 03 expedition.

    Posted on Mar 07, 2009

    Add Your Answer

    Uploading: 0%

    my-video-file.mp4

    Complete. Click "Add" to insert your video. Add

    ×

    Loading...
    Loading...

    Related Questions:

    2 Answers

    2014 ford fusion engine wont crank after wreck


    Ford fusion won't start - YouTube

    ? 2:01
    www.youtube.com/watch?v=H0BhHWT2cyY
    Sep 16, 2014 - Uploaded by mlmunoz21
    Ford fusion won't start ... Published on Sep 16, 2014 .... 2004-2008 F150 Died Out No Crank Theft Light ...

    Ford Fusion won't start - YouTube

    ? 0:32
    www.youtube.com/watch?v=lmH7R6Ebmyc
    Jan 9, 2015 - Uploaded by Nicholas A.
    Any ideas why it won't start? 2007 ford Fusion awd 6 cylinder. ... And P1260 2007 Ford Fusion - Theft ...

    Nov 02, 2015 | 2014 Ford Fusion

    1 Answer

    2007 ford f150 5.4 Excessive crankcase vacuum, ,pcv clear , Pulling air passed the rear main seal causing a whistle/buzz


    the pcv valve should only work on deceleration or when there is excessive pressure build up in the sump
    max vacuum in an engine is 22 inches of mercury on hard deceleration and 15 "hg on idle to have vacuum in the sump indicates a faulty pcv valve so I would replace it with a known good one

    Aug 08, 2015 | Ford Cars & Trucks

    1 Answer

    Where is the TCM located on a 2007 ford fusion 2.3


    ford fusion V6 ,our fusion is only a little car with mainly a diesel engine here although some are petrol with a 1.4 citreon/peugeot engine

    Nov 21, 2014 | 2007 Ford Fusion V6

    2 Answers

    When shouldpcv be changed on 2008 ford edge


    If you are able, get a original part and change it following the services / warranty list of parts, that the dealer change according the miles. If you buy the PCV in a regular auto store; more frecuently, maybe half the time. Hope this helps. Take care.

    May 15, 2014 | 2008 Ford Edge

    1 Answer

    2008 Ford Fusion PCV Valve??


    yes it has a 2 wire connector.

    Jul 16, 2013 | Cars & Trucks

    1 Answer

    Rear brake cailpers won't collapse on 2007 ford fusion


    Open bleeder valve & push caliper piston, in as
    you rotate piston to screw in parking brake

    Do this by hand,only use a clamp on the front calipers

    Apr 08, 2013 | 2008 Ford Fusion

    1 Answer

    PCM Valve inside transmission?


    I would try another shop, A PCM Valve is not typically that hard to replace from my experience in older model Fords it sits up on top of the motor near the Crankcase.

    The blowby vapors that end up in an engine's crankcase contain moisture as well as combustion byproducts and unburned fuel vapors. The crankcase is sealed to prevent the escape of these gases into the atmosphere, but the vapors must be removed to prevent oil contamination that leads to sludge formation. The positive crankcase ventilation (PCV) system siphons these vapors from the crankcase and routes them into the intake manifold so they can be reburned in the engine.
    The main component in the PCV system is the PCV valve, which is usually located in the valve cover. A hose connects the PCV valve to the intake manifold. A second hose between the air cleaner and crankcase or other valve cover (V6 or V8 applications) provides fresh air to help flush the vapors out of the crankcase. Some engines have a separate air filter for the PCV breather hose located inside the air cleaner. The PCV valve is a spring-loaded valve with a specific orifice size designed to restrict the amount of air that's siphoned from the crankcase into the intake manifold. This is necessary because air drawn through the valve from the crankcase has a leaning effect on the fuel mixture much the same as a vacuum leak. So air flow through the valve must be controlled within certain limits. At idle, air flow is reduced because little blowby is produced. When the engine is cruising and vacuum is high, airflow through the PCV valve is at a maximum to purge the blowby vapors from the crankcase.
    It's important to note that PCV valves are sized for specific engine applications. The wrong PCV valve for an application can flow too much or too little air causing driveability problems. Varnish deposits can clog the valve, so replacement for preventative maintenance is recommended (every 50,000 miles usually).
    Not all engines have PCV valves. Some (like Ford Escort, GM FWD cars with the Quad Four engine, etc.) ventilate the crankcase with a small breather hose and calibrated orifice. There is no spring-loaded PCV valve. On these applications, no maintenance is usually necessary.

    All this to say that if this shop does not know this then i would look for another shop. Try going to the Better Business Burea for your area online and check some shops that have beenin business for a while. Also read customer reviews before making a decision and call them to ask some questions to see if they have ever done one of these replacements before.
    Hope this helps, Good Luck!!

    May 29, 2012 | 2007 Ford Freestyle

    Not finding what you are looking for?
    Cars & Trucks Logo

    Related Topics:

    613 people viewed this question

    Ask a Question

    Usually answered in minutes!

    Top Ford Experts

    yadayada
    yadayada

    Level 3 Expert

    75117 Answers

    Colin Stickland
    Colin Stickland

    Level 3 Expert

    22095 Answers

    fordexpert

    Level 3 Expert

    5474 Answers

    Are you a Ford Expert? Answer questions, earn points and help others

    Answer questions

    Manuals & User Guides

    Loading...