Question about 1996 Volvo 850

Open Question

Where is the blend door actuator on a volvo 850 located

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
repairpal
  • 128 Answers

SOURCE: Volvo 850 oil pressure sending unit

It's on the engine, right next to the starter, it has one wire going to it. You don't need to drain the oil. If the light is coming on, you may have bad seals in the oil pan, a fairly common problem, but replacing the switch is a good fisrt step.

Posted on Jan 27, 2009

Ad
ginko
  • 19396 Answers

SOURCE: WHERE IS THE SENTOR LOCATED ON 1996 VOLVO TURBO 850

Copy and paste the link below on your browser address bar (eg. on Internet Explorer): http://www.volvoclub.org.uk/faq/EngineSensors.html#OxygenSensorLifeandDiagnostics

Posted on Jun 06, 2009

  • 20 Answers

SOURCE: Cannot open the gas cap for a 1995 Volvo 850

pop the trunk, same side as gas door pull the interior carpet down or back. Look for a wire with a loop on the end, pull it. "The door should open

Posted on Sep 28, 2009

  • 1 Answer

SOURCE: where is switch located to open the fuel door?

Hi Midwin4U,

I had the same question when I got my 94' 850 Turbo wagon. I kept wondering where the fuel door release was. To my surprise there was not one, you simply must have the entire "CAR" (not just the drivers door) unlocked. Use the key FOB. After that, go to the fuel door outside the vehicle and push in on it to pop it open. Hopefully you have not run out of gas yet.

Posted on Dec 22, 2009

emissionwiz
  • 76846 Answers

SOURCE: where is my shift cable on a 96 volvo 850

At the transmission.

Posted on Dec 27, 2012

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Where is rhe air temp. Door actuator in a 2003 ford 450 truck


Ford Superduty Erratic Temp Blend Door Actuator Removal - YouTube

? 12:29
https://www.youtube.com/watch?v=dYPOtin3JUk
Dec 1, 2013 - Uploaded by FordTechMakuloco
Only buy the Ford Actuators, you can get them cheaper here- ...

Simple how to fix blend door heater a/c actuator 2002 - 2008 ford ...

? 7:12
https://www.youtube.com/watch?v=EEWuJuhCtmc Aug 24, 2013 - Uploaded by kirk colombo
Simple how to fix blend door heater a/c actuator 2002 - 2008 ford explorer noise .... I literary just finish ...

08-10 Super Duty Blend Door Actuator Location - Dual System ...

? 1:24
https://www.youtube.com/watch?v=s7awF2fTKf4 Mar 22, 2012 - Uploaded by srmastertech
Here is a quick view showing the location of the temp blend door actuators on the Ford Super Duty's with ...

Ford blend door fix - 15 minutes - YouTube

? 3:22
https://www.youtube.com/watch?v=wsjGxreGlkA Jul 21, 2013 - Uploaded by SoonersWarriors
Ford blend door fix - 15 minutes. SoonersWarriors. Loading ... Ford Vehicles: Frequent Blend Door Actuator ...

Blend Door Actuator Ford Super Duty 08-10 - YouTube

? 9:45
https://www.youtube.com/watch?v=mbzjCPYENZQ Oct 4, 2013 - Uploaded by MostExcellentDude
This applies to 2008-2010 F250 and F350 with the dual climate control. This video shows the locations for the ...
blend door actuator 2003 ford f450 Google Search




Aug 16, 2017 | Ford Cars & Trucks

1 Answer

Location of passenger side blend door actuator on 2006 mercury mountaineer auto controls, 6 cylinder


Temperature Blend Door Actuator - RH, EATC Removal and Installation
  1. Remove the RH floor console finish panel.
  1. Lower the glove compartment.
  1. Disconnect the RH temperature blend door actuator electrical connector.
  2. Remove the 3 RH temperature blend door actuator screws.
    1. Remove the RH temperature blend door actuator.
2006 2010 Ford Explorer NO Heat Passenger Temp Actuator Replacement same as mountaineer

Jun 19, 2017 | Mercury Cars & Trucks

1 Answer

How do i fix a stuck blend door on 2010 dodge nitro?


I would pull off the blend door actuator and swap it out with a new one. Or another option is to swap it out with one of the other actuators. The blend door actuator is interchangeable with the actuators for the mode-air doors and the recirculation-air door.

Disconnect and isolate the negative battery cable.

If equipped, remove the silencer from below the driver side of the instrument panel.

Disconnect the wire harness connector from the blend door actuator located on the driver side of the air distribution housing.

Remove the two screws that secure the blend door actuator to the actuator mounting bracket and remove the actuator

Feb 17, 2015 | 2010 Dodge Nitro

1 Answer

Blend door stuck open, buick lesabre custom,can not locate blend door to close it


it is controlled by an electronic actuator. look up blend door actuator on google with your year make and modle and it will show a diagram and location, also a part number if you would like to replace.

Nov 01, 2013 | Cars & Trucks

1 Answer

No heat Heater core is hot


If heater core is getting coolant circulating through it then you may have a temp blend door, or blend door actuator not working properly. The blend door is located in the air box under the dash, and the actuator is located on the air box. You may be able to visually check the operation while turning the temp knob, by locating the coresponding actuator on the air box and monitoring the movement. If it is moving ok and still no heat then the blend door, or lever is broken, which will require removal of the dash.

Oct 17, 2009 | 2001 Dodge Ram 2500 Truck

1 Answer

Cant find the blend door actuator on 2003 ford f150 super crew


The temperature blend door actuator is located on the right side of the transmission hump under the evap. case. The floor ducts cover it.

Jun 21, 2009 | 2003 Ford F150 Regular Cab

3 Answers

01 silverado blend door changed /now works back wards!!!


most likely needs a LH (bottom) temp actuator. Located in the center of the dash on the bottom, you have to remove the hush panel on the rh side of the truck

Apr 24, 2009 | 2001 Chevrolet Silverado

2 Answers

Heating system only blows out hot air through the vents


I would look at the air blend doors first, it sound like they are not working or your control in the dash is not working send a signal to them. they work by changing the air from hot to cold or in between.

Avalanche, Sierra And Silverado
  1. Remove the floor air outlet duct extension (1) from the floor duct (2). 0900c152801c9c8a.jpgRemove the floor air outlet duct extension (1) from the floor duct (2)
  2. Disconnect the electrical connection at the blend door actuator (10). 0900c152801c9c8b.jpgBlend door actuator and related components
  3. Remove the blend door actuator mounting screws from the HVAC module.
  4. Remove the blend door actuator as an assembly with the actuator cam. 0900c152801c9c8c.jpgRemove the blend door actuator mounting screws from the HVAC module
To install:
  1. Install the blend door actuator as an assembly with the actuator cam.
    1. Line up the heater/defroster valve lever with the blend door actuator cam slot.
    2. Line up the A/C valve lever with the blend door actuator cam
  2. Install the blend door actuator mounting screw to the HVAC module.
    1. Tighten the blend door actuator mounting screw to 14 inch lbs. (1.6 Nm).
  3. Connect the electrical connection at the blend door actuator (10). 0900c152801c9c8b.jpgBlend door actuator and related components
  4. Install the floor air outlet duct extension (1) to the floor air duct (2).
C/K Series
  1. Disconnect the electrical connector to the mode actuator that is located on the left side of the air distribution case.
  2. Remove the screws.
  3. Remove the adjuster links from the control lever.
  4. Remove the mode actuator.
  5. Adjust the mode actuator by completing the following steps:
    1. Connect the electrical connector to the actuator.
    2. Turn the ignition switch to the RUN position. Allow the self-positioning of the actuator.
    3. Turn the ignition switch to the OFF position.
    4. Remove the actuator from the electrical connection. 0900c152801c9c8d.jpgBlend door actuator-C/K Series
To install:
  1. Install the mode actuator.
  2. Install the screws.
  3. Install the adjuster links to the control lever.
  4. Connect the electrical connector.
  5. Test the circuit operation

Nov 27, 2008 | 2001 Chevrolet Silverado

Not finding what you are looking for?
1996 Volvo 850 Logo

Related Topics:

52 people viewed this question

Ask a Question

Usually answered in minutes!

Top Volvo Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6918 Answers

Are you a Volvo Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...