Question about 1994 Mazda 323

Open Question

Turbocharged mazda BP1800 4w Abs 323 sedan running lean

Running lean

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
A 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
The service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Good luck!

Posted on Jan 02, 2017

Ad
  • 1 Answer

SOURCE: ABS, Traction control and handbrake

I have a Mazda Capella (626) 1998 and had similar problem other than it was running on 4 cylinders and the hand brake light was not on but speedometer was not functioning and the ABS light was on. The rear ABS senssor was the problem.
SDM

Posted on Jan 23, 2009

Ad
  • 91 Answers

SOURCE: I have a 2005 mazda rx8. After running for a few

sounds like it needs to be taken to a madza approved repairer for then to be plugged in for a dianostic annalisis, too many warning lights for one fuse.

Posted on Jul 25, 2009

sawdust46694
  • 398 Answers

SOURCE: i replaced the ignition coil of my mazda 323 sedan

timming check pull # 1 plug hold your thumb or better yet a compression tester in the # 1 plug hole . and watch the rotor go around. look at the cap and wire to see where # 1 is.
I locate #1 plug and wire before I pull the dist cap. When it pushes out air it must be pointing to # 1.... hope this helps you

Posted on Aug 10, 2009

Nur017
  • 8 Answers

SOURCE: trying to find the transmission

ok , there is not dip stick on interplay engine. you can check from speed sensor. if you want to change or flushing the new one. please remove drain plug for go out oil from below. and than open speed sensor for filling the oil, but be carefully. because there are so many critical part (rotary pulse encoder speed).

please try
my number call +6281808024008

Posted on Jul 19, 2011

  • 14036 Answers

SOURCE: Where can i buy a

MAZDA DEALERSHIP FOR MAZDA PARTS.CANT GIVE YOU PRICE BROKEN CAM SHAFT COULD MEAN CYLINDER HEAD DAMAGE AND DAMAGE VALVES.PISTON DAMAGE THIS NOT A CHEAP FIX.

Posted on Aug 13, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

HOW TO FIND OUT THE YEAR OF MANUFACTURE OF A MAZDA 323 SEDAN 130


should be on id plate inside door jam on drivers side.

May 21, 2013 | Cars & Trucks

1 Answer

Mazda 323 1994 sedan loose power on 4th and 5th gear topspeed is 100kph


Check the engines compression. This has been known to happen on real tierd engines that have poor compression, with it comes lack of power from the combustion cycles. If the rpm is raising quickly, and speed isn't, your clutch could be slipping.

Oct 08, 2012 | 1994 Mazda 323

2 Answers

Why does my 1990 mazda 323 start good, then stall and not start again?


For car stalling and quit running problem,click the link below for troubleshooting:----http://technoanswers.blogspot.in/2012/02/1990-mazda-323-stalls-and-quit-running.html
--------This will help.Thanks.

Feb 07, 2012 | Mazda 323 Cars & Trucks

1 Answer

How can I reset ABS codes on 1999 mazda 323


Hi Tony, To reset the readout you'll need to take the vehicle to someone with a scanner and have it done there. Have you attended to the fault/s which were showing? Regards Johngee10

Aug 20, 2011 | 1994 Mazda 323

2 Answers

ABS, Traction control and handbrake light is on. Car was running on 3 cylinders previous to the lights coming on. 1999 Mazda SP20 Familia (323)


I have a Mazda Capella (626) 1998 and had similar problem other than it was running on 4 cylinders and the hand brake light was not on and the ANSWER was a speed sensor which is to do with ABS system needed replacing. You can determine which one is broken by putting volt meter over each of them.

Nov 17, 2008 | Mazda 323 Cars & Trucks

1 Answer

Gtx mazda 323


Im not an expert by any means but it sounds like you are running out of fuel in the combustion chamber (or lean) and setting off the cars knock sensor. It seems to me there are several fuel pumps available on ebay eluding to the fact that they were a weak component. be extremely careful "pinging" is extremely BAD for the pistons and block. keep out of hard boost until you solve issue.

Nov 08, 2008 | 1989 Mazda 323

1 Answer

1989 Mazda 323 gtx BG


Two things...
You should follow the pin numbers and not the color code.
Second
Check online for a service manual from Japan or the USA for that car. We got many Mazda imports here and there should be a lot of books on Ebay that would have the electrical schematics for a 323 from the USA and Canada.
You are going to have to just buy a book and have it shipped to NZ.

Jun 20, 2008 | 1989 Mazda 323

Not finding what you are looking for?
1994 Mazda 323 Logo

Related Topics:

19 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mazda Experts

yadayada
yadayada

Level 3 Expert

78267 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8836 Answers

Are you a Mazda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...