Question about 1999 Toyota Camry

1 Answer

Valve cover torque

Need to know foot pounds of torque to tighten valve cover on a 2000 toyota camary 4cyl

Posted by on

  • 1 more comment 
  • Anonymous Mar 13, 2014

    torque specs

  • Anonymous Mar 13, 2014

    torque spces

  • Anonymous Mar 14, 2014

    Foot pounds or Newton meters will be fine. Thank you.

×

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 16 Answers

17 ft lbs

Posted on Jan 23, 2009

1 Suggested Answer

  • 1214 Answers

SOURCE: torque for valve cover

Usually not over 30 ft-pounds.

Posted on Jan 23, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

I need the torque spec for the valve cover on a 06mercury malin


There is a torque spec for the cylinder head; I don't know of one for the cover.

Jul 14, 2015 | Cars & Trucks

2 Answers

2001 daewoo lanos dual overhead 1.6 liter head bolt torque and sequence


  1. Tighten cylinder head bolts to 25 N.m (18 ft. lbs.). Tighten bolts an additional 70 degrees plus 70 degrees plus 30 degrees using angular torque gauge .
2001-daewoo-lanos-dual-overhead-1-6-vrq3bch1e30nz1jlq5sn5nnt-4-0.gif

Oct 20, 2011 | 2000 Daewoo Lanos

2 Answers

Valve cover gaskets


Valve cover gaskets are a snap, even for a real dummy.  Get a set, don't fall for the "BEST IN THE MARKET".  All you need is a cheap set of something, that will seal the covers.  Get a small tube or bottle of NON-HARDENING sealer.  Clean both surfaces , put some sealer on the engine, and the valve cover, put the gasket in place and tighten it down to a few foot pounds of torque.  It doesn't need to be cranked down tight enough to hold back an elephant, just enough to squeeze the gasket.  Let it dry overnight before you start the engine.

Feb 06, 2010 | 1998 Mercury Mystique

2 Answers

How do you change spark plugs on a toyota yaris 2001


First you must remove the plastic cover from on top of the engine to access the ignition coils. The next step is to remove the ignition coils. To do this you must carefully disconnect the plug by holding down the plastic tab while pulling the plug off the coil. Then you must remove the small bolts holding the coils to the valve cover. Pull the coils straight out. To remove the spark plugs you will need a torque wrench, long extension and a self holding spark plug socket. All these can be bought at your local auto parts store. The spark plugs are removed by unscrewing them from the cylinder head and pulling them straight out. Installation is the reverse of removal. The spark plugs are tightened to 25 foot pounds of torque and the small bolts for the ignition coils are tightened to 10 foot pounds of torque.

Oct 23, 2009 | 2007 Toyota Yaris

2 Answers

Need the cylinder head torque settings on a toyota corolla 1990 model ae92 wiht a 4a-fc engine


Tighten in several passes to 44 foot pounds.

I just wanted to add. Since this is an aluminum cylinder head, I hope you loosened the head in the loosening torque pattern. The pattern opposite of the torque tightening pattern. If not, you stand the chance of warping the head.

Again, since it's an aluminum head, it needs to be checked for flatness. Most aluminum heads need to be surfaced before re-installing.

Tightening torque pattern is as follows:

1.The Drivers side of the engine is the Left side.
From the Front going towards the back; the bolts are numbered 10, 6, 1, 3, and 7.
From the Front going towards the back on the Passenger side; the bolts are numbered 8, 4, 2, 5, and 9.

The Exhaust and Intake Camshaft Bearing Cap bolts go to 9 foot pounds. Tighten gradually. One bolt to the other with so many foot pounds, work back, and forth up to 9lbs.

Camshaft Timing Pulley bolts go to 43 foot pounds. (In a tightening sequence, and gradually)

Jul 25, 2009 | 1990 Toyota Corolla

2 Answers

Torque specs for toyota tercel


Hello vienotkelly: The correct Main bolt torque is 42 foot pounds. The connecting rods torque to 29 foot pounds. The torque sequence for the head bolts and the correct way to tighten the bolts are attached to this reply. Thak You for using6bd0ae1.jpg FixYa. Roger

Apr 08, 2009 | 1998 Toyota Tercel

1 Answer

Torque for valve cover


Usually not over 30 ft-pounds.

Jan 23, 2009 | 1999 Toyota Camry

1 Answer

Need to know what tourque for the valve cover bolts, 97 tercel


10 foot/pounds. Hint from experience, change the gasket.

Dec 04, 2008 | 1997 Toyota Tercel

Not finding what you are looking for?
1999 Toyota Camry Logo

Related Topics:

564 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toyota Experts

yadayada
yadayada

Level 3 Expert

60867 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6811 Answers

Are you a Toyota Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...