Question about 1995 Volkswagen GTI
Tried switching motors but to no avail ,new switch did not help
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Posted on Jan 02, 2017
SOURCE: problem with power-windows
THis is common Too common. As I posted before.
As I posted in the Passat questions.
The jetta may slightly differ.
Yes. If your window has fallen down and will not roll up.
99% Chance you car is suffering the Infamous VW plastic clip.
The door panel comes off With a T-10 torx or a Hex (Allen) wrench
that will fit and A large Philips Screw Driver..
Remove the Plastic cover on the inside Door handle.
And the Screw or Screw along the Bottom of the door panel.
Then remove the screws that hold the handle the the door.
They are located behind the Plastic plate you removed with a tiny screw driver earlier... Be careful not the mark up the cover whaytprying it up. It is best to pry from underneath. Where marks if made can not be seen
After the screws are out 4 I believe. The Use of a CLip tool ir best.
For getting behind the panel to pop it off. A screw driver will work.
After all the clips are released. Pull the light at the bottom of the panel down and out. Disconnect it ur push it back thought the hole it came from..
Now you need a 10mm socket, or wrench to remove the 12 bolts that hold the metal plate to the Door. Remove all the 10mm bolts, If the widow has not already fallen in the door. It should be released. By removing the Black 2" plugs. THe loosen the bolts that clamp the window the the arms. DO NOT LOOSEN THEM ALL the way, .
Disconect the all the wiring.. THe Door lock cable,can be a pain.
I think it pulls down,.
Next remove the Metal plate. that is the regulator.
reverse to install
Posted on Jun 26, 2009
wires go thru the boot. most likely broken wire from the switch. if the window works with the key in the door
Posted on Sep 04, 2009
Tips for a great answer:
Nov 07, 2015 | Cars & Trucks
Aug 19, 2014 | 1995 Ford Taurus
Nov 24, 2012 | Cars & Trucks
Window fuse's and relay's may be up under driver or passenger side dash or behind glove box, under the hood and even under the seats, and finally on the ends of the dash. All passenger power windows and locks are controlled thru and get power from the master control switch on the drivers door.
Drivers door window gets used the most so it could be the motor, window switch, relay or fuse.
Could also be a broken wire in the rubber boot going from the door to the body. You will have to eliminate each till you find the culprit. Check that all switches return to neutral when released.
The motor and the relay are the most likely to cause this problem. Try swapping the relay with a working window relay. If it still doesn't work, remove the door panel and remove the window motor.
Turn the motor shaft in both directions by hand several turns. Then plug the motor in and see if the switch will now run the motor. Sometimes that's all it takes to get it working again. I have had to do this with brand new motors. If voltage is not present at the motor connector, either a bad switch or a broken wire exists. Make sure to check for voltage coming to that windows switch. Actually, GM use's a circuit breaker type relay for each window and one fuse for all the circuit breakers.
Open the door, turn the key to the ON position without starting the engine and everything that makes noise is off. Lean down placing your ears close to the bottom center of the door or at the speaker grill. Press the window switch UP and DOWN. Listen for the window motor. If heard the drive is damaged. If not heard, turn key off and locate and replace the relay with one of the other window relays. Check window again. If it works now, get a new relay. More often than not, removing the motor and turning it by hand will get it working good as new. I have had to do that with Brand New motors! So try it.
If all has failed, with the door panel still off, check for voltage at the motor connector when pushing the window switch. No voltage means its the switch, especially if its a auto down or up switch.
Aug 25, 2011 | Pontiac Bonneville Cars & Trucks
Oct 11, 2017 | 1995 Ford Windstar
Aug 13, 2010 | 1995 Chevrolet Blazer
Mar 22, 2010 | 1994 Toyota Camry
Sep 03, 2009 | 1997 Volkswagen Golf
Jul 21, 2009 | 1995 Dodge Dakota
Feb 26, 2009 | 1995 GMC Safari
Jul 01, 2017 | 1995 Volkswagen GTI
31 people viewed this question
Usually answered in minutes!
Step 2: Please assign your manual to a product: